• CN:11-2187/TH
  • ISSN:0577-6686

机械工程学报 ›› 2026, Vol. 62 ›› Issue (18): 425-437.doi: 10.3901/JME.260753

• 运载工程 • 上一篇    

扫码分享

套筒-镂空凹口翅片耦合相变材料的圆柱形锂离子电池热管理系统设计与性能研究

武小兰, 赵兴欣, 白志峰, 杨乃兴   

  1. 西安建筑科技大学机电工程学院 西安 710055
  • 收稿日期:2025-09-22 修回日期:2026-05-09 发布日期:2026-11-20
  • 作者简介:武小兰,女,1975年出生,博士,副教授,硕士研究生导师。主要研究方向为智能网联新能源汽车技术。E-mail:wuxiaolan@xauat.edu.cn;赵兴欣,男,1999年出生,硕士研究生。主要研究方向为锂离子电池热管理技术。E-mail:zhaoxingxin@xauat.edu.cn;白志峰(通信作者),男,1974年出生,博士,讲师,硕士研究生导师。主要研究方向为新能源汽车与微电网技术。E-mail:zhifeng.bai@xauat.edu.cn;杨乃兴,男,1986年出生,博士,副教授,硕士研究生导师。主要研究方向为电动汽车电池管理系统。E-mail:yangnaixing@xauat.edu.cn
  • 基金资助:
    国家自然科学基金(51405367)、陕西省重点研发计划(2025CY-YBXM-095)和中央引导地方科技发展资金(XZ202301YD0003C)资助项目。

Design and Performance Study of Thermal Management System Coupling Sleeve and Hollow-notched Fins with Phase Change Material for Cylindrical Lithium-ion Batteries

WU Xiaolan, ZHAO Xingxin, BAI Zhifeng, YANG Naixing   

  1. School of Mechanical and Electrical Engineering, Xi'an University of Architecture and Technology, Xi'an 710055
  • Received:2025-09-22 Revised:2026-05-09 Published:2026-11-20

摘要: 相变材料凭借其储存和释放潜热的能力,为锂离子电池热管理系统提供了极具前景的解决方案,但其较低的导热性能常导致系统在高负荷放电工况下出现散热迟滞与局部潜热饱和问题。针对这一问题,提出一种应用于圆柱形锂离子电池的套筒-镂空凹口翅片耦合相变材料的无源热管理系统。通过对翅片实施差异化镂空策略,实现了热流路径与相变材料分布的优化。数值模拟结果表明,该设计在显著提升系统散热效能的同时实现了轻量化。在大倍率放电工况下,电池组最高温度降低7.43 ℃,各电池间温差控制在2 ℃以内;在采用不同潜热与导热性能的相变材料时,最高温度较基础模型可进一步降低0.87~3.81 ℃。此外,在热失控场景下,该系统可将失控电池表面温度降低43%,并使最高温度下降速率提升59%。

关键词: 锂离子电池, 电池热管理系统, 相变材料, 翅片结构

Abstract: Phase change materials(PCMs) provide a highly promising solution for lithium-ion battery thermal management systems due to their ability to store and release latent heat. However, their inherently low thermal conductivity can cause heat dissipation lag and local latent heat saturation under high-load discharge conditions. To address this issue, a passive thermal management system that couples a sleeve and hollow-notched fins with PCM is proposed for cylindrical lithium-ion batteries. By implementing a differentiated hollowing strategy on the fins, the heat flow pathways and PCM distribution are optimized. Numerical simulation results demonstrate that the proposed design significantly enhances the system's heat dissipation efficiency while enabling lightweight construction. Under high-rate discharge conditions, the maximum battery pack temperature is reduced by 7.43 °C and the temperature difference between cells is kept to within 2 °C. When PCMs with different latent heat and thermal conductivity are used, the maximum temperature decreases by a further 0.87-3.81 °C compared with the baseline model. Furthermore, in thermal runaway scenarios, the surface temperature of the runaway cell decreases by 43%, and the peak temperature decrease rate increases by 59%.

Key words: lithium-ion battery, battery thermal management system, phase change material, fin structure

中图分类号: