7075铝合金超低温变形行为与回弹预测研究

doi:10.3901/JME.2025.14.099

机械工程学报 ›› 2025, Vol. 61 ›› Issue (14): 99-107.doi: 10.3901/JME.2025.14.099

• 特邀专栏：铝合金薄壁构件超低温成形制造新原理 • 上一篇下一篇

扫码分享

7075铝合金超低温变形行为与回弹预测研究

戚宇彤^1,2, 孙楚研^1,2, 李淑慧^1,2

1. 上海交通大学机械系统与振动全国重点实验室上海 200240;
2. 上海交通大学上海市复杂薄板结构数字化制造重点实验室上海 200240

收稿日期:2025-01-22 修回日期:2025-03-08 出版日期:2025-07-20 发布日期:2025-08-25
作者简介:戚宇彤，男，1994年出生，博士研究生。主要研究方向为铝合金板材成形技术。E-mail:qiyutong@sjtu.edu.cn;李淑慧(通信作者)，女，1973年出生，博士，教授，博士研究生导师。主要研究方向为薄板结构智能制造、塑性成形理论与数值模拟。E-mail:lishuhui@sjtu.edu.cn
基金资助:
国家重点研发计划(2019YFA0708803)和国家自然科学基金(52475377)资助项目。

Study on the Deformation Behavior and Springback Prediction of 7075 Aluminum Alloy at Cryogenic Temperature

QI Yutong^1,2, SUN Chuyan^1,2, LI Shuhui^1,2

1. State Key Laboratory of Mechanical System and Vibration, Shanghai Jiao Tong University, Shanghai 200240;
2. Shanghai Key Laboratory of Digital Manufacture for Thin-walled Structures, Shanghai Jiao Tong University, Shanghai 200240

Received:2025-01-22 Revised:2025-03-08 Online:2025-07-20 Published:2025-08-25

摘要/Abstract

摘要： 以预时效态的7075铝合金板材为试验材料，进行室温和-196 ℃下的单向拉伸、拉伸-卸载、拉伸-压缩以及U型件弯曲回弹试验，结合有限元仿真，分析超低温变形行为和回弹规律。结果表明，超低温下预时效态7075铝合金在单向拉伸时表现出延伸率提高和硬化能力增强的双增效应，在循环拉伸-卸载过程中弹性模量随应变衰减速率更快，在拉伸-压缩加载过程中表现出更显著的提前屈服现象和瞬态行为，包辛格效应增强，且超低温下U型件回弹量略大于室温。考虑到正反向加载时材料的硬化差异，使用不同的正反向硬化参数对初始Y-U模型进行修正。相比于初始Y-U模型，修正的模型能够更好地描述-196 ℃下的拉伸-压缩循环加载变形行为，并具备更高的U型件超低温回弹预测精度。

关键词: 超低温变形, 7075铝合金, 包辛格效应, 硬化模型, 回弹预测

Abstract: Taking the pre-aged 7075 aluminum alloy sheet as experimental material, the uniaxial tension, tension-unloading, tension-compression and U-bending springback tests were conducted at room temperature and -196 °C. Combined with finite element simulation, the deformation and springback behavior at cryogenic temperature were analyzed. The results show that the pre-aged 7075 aluminum alloy exhibits the dual enhancement effect of enhanced elongation and hardening ability in uniaxial tension at cryogenic temperature. During tension-unloading tests, the cryogenic elastic modulus decays faster with strain. The early yielding and transient behavior are more prominent during tension-compression tests, which means the Bauschinger effect is enhanced at cryogenic temperature. Moreover, the cryogenic springback of the U-bending specimen is slightly larger than that at room temperature. Considering the difference between forward and reverse hardening, the initial Y-U model was modified with different hardening coefficients in forward and reverse loading. At cryogenic temperature, the modified Y-U model could both describe tension-compression curve better and have higher prediction accuracy for the springback of U-bending specimen.

Key words: cryogenic deformation, 7075 aluminum alloy, Bauschinger effect, hardening model, springback prediction

中图分类号:

TG146

戚宇彤, 孙楚研, 李淑慧. 7075铝合金超低温变形行为与回弹预测研究[J]. 机械工程学报, 2025, 61(14): 99-107.

QI Yutong, SUN Chuyan, LI Shuhui. Study on the Deformation Behavior and Springback Prediction of 7075 Aluminum Alloy at Cryogenic Temperature[J]. Journal of Mechanical Engineering, 2025, 61(14): 99-107.

导出引用管理器 EndNote|Reference Manager|ProCite|BibTeX|RefWorks

链接本文: http://www.cjmenet.com.cn/CN/10.3901/JME.2025.14.099

http://www.cjmenet.com.cn/CN/Y2025/V61/I14/99

参考文献

[1] ZHENG K，POLITIS D J，WANG L，et al. A review on forming techniques for manufacturing lightweight complex- shaped aluminium panel components[J]. International Journal of Lightweight Materials and Manufacture，2018，1(2):55-80.
[2] 甘国强，李萍，薛克敏. 汽车件高强铝合金板件热冲压工艺研究进展[J]. 稀有金属，2024，48(4):564-574. GAN Guoqiang，LI Ping，XUE Kemin. Research progress on hot stamping process of high strength aluminum alloy plates for automotive parts[J]. Chinese Journal of Rare Metals，2024，48(4):564-574.
[3] YUAN S，CHENG W，LIU W，et al. A novel deep drawing process for aluminum alloy sheets at cryogenic temperatures[J]. Journal of Materials Processing Technology，2020，284:116743.
[4] GRUBER B，WEIßENSTEINER I，KREMMER T，et al. Mechanism of low temperature deformation in aluminium alloys[J]. Materials Science and Engineering:A，2020，795:139935.
[5] JIN M，LEE B，YOO J，et al. Cryogenic deformation behaviour of aluminium alloy 6061-T6[J]. Metals and Materials International，2024，30(6):1492-1504.
[6] 凡晓波，洪吉庆，赖小明，等. 铝锂合金曲面件超低温成形工艺[J]. 宇航材料工艺，2021，51(4):126-130. FAN Xiaobo，HONG Jiqing，LAI Xiaoming，et al. Process of cryo-forming for Al-Li alloy curved-shaped components[J]. Aerospace Materials Technology，2021，51(4):126-130.
[7] FAN X，CHEN X，YUAN S. Novel forming process for aluminum alloy thin shells at ultra-low temperature gradient[J]. International Journal of Machine Tools and Manufacture，2023，185:103992.
[8] WANG C，YI Y，WANG H，et al. Investigation on the formability and deformation mechanism of aluminum alloy thin-walled parts at cryogenic temperature[J]. Journal of Materials Processing Technology，2023，319:118041.
[9] GRABNER F，ÖSTERREICHER J A，GRUBER B，et al. Cryogenic forming of Al-Mg alloy sheet for car outer body applications[J]. Advanced Engineering Materials，2019，21(8):1900089.
[10] FENG B，GU B，LI S. An efficient pre-hardened cryogenic forming process for AA7075 aluminum alloy sheets[J]. Journal of Manufacturing Processes，2023，92:534-547.
[11] DONG F，YI Y，HUANG S，et al. Cryogenic formability and deformation behavior of 2060 Al-Li alloys with water-quenched and T4 aged temper[J]. Materials Science and Engineering:A，2021，823:141722.
[12] GRABNER F，GRUBER B，SCHLÖGL C，et al. Cryogenic sheet metal forming:An overview[J]. Materials Science Forum，2018，941:1397-1403.
[13] FENG B，GU B，LI S. Cryogenic deformation behavior and failure mechanism of AA7075 alloy sheets tempered at different conditions[J]. Materials Science and Engineering:A，2022，848:143396.
[14] LIU W，CHENG W，YUAN S. Analyses on formability and flow stress of an Al-Cu-Mn alloy sheet under biaxial stress at cryogenic temperatures[J]. International Journal of Mechanical Sciences，2021，195:106266.
[15] DAROJU S，KUWABARA T，SHARMA R，et al. Experimental characterization and crystal plasticity modeling for predicting load reversals in AA6016-T4 and AA7021-T79[J]. International Journal of Plasticity，2022，153:103292.
[16] FAN X，WANG Q，WU F，et al. Cryogenic springback of 2219-W aluminum alloy sheet through V-shaped bending[J]. Transactions of Nonferrous Metals Society of China，2024，34(10):3185-3193.
[17] WU F，FAN X，YANG G，et al. Dimensional change and springback of spherical shell in cryogenic forming[J]. International Journal of Mechanical Sciences，2024，284:109757.
[18] WAGONER R H，LIM H，LEE M-G. Advanced Issues in springback[J]. International Journal of Plasticity，2013，45:3-20.
[19] 郑学斌，韩龙帅，李学涛，等. DP780双相钢U弯回弹预测影响因素研究[J]. 机械工程学报，2024，60(6):197-206. ZHENG Xuebin，HAN Longshuai，LI Xuetao，et al. Study on influencing factors of U-bending springback prediction of DP780 dual-phase steel[J]. Journal of Mechanical Engineering，2024，60(6):197-206.
[20] GU B，HE J，LI S，et al. Cyclic sheet metal test comparison and parameter calibration for springback prediction of dual-phase steel sheets[J]. Journal of Manufacturing Science and Engineering，2017，139(9):091010.
[21] DONG H，LI X，LI Y，et al. An experimental and modelling study of cyclic tension-compression behavior of AA7075-T6 under electrically-assisted condition[J]. Journal of Materials Processing Technology，2022，307:117661.
[22] ZANG S，LEE M G，SUN L，et al. Measurement of the Bauschinger behavior of sheet metals by three-point bending springback test with pre-strained strips[J]. International Journal of Plasticity，2014，59:84-107.
[23] YOSHIDA F，UEMORI T. A model of large-strain cyclic plasticity describing the Bauschinger effect and workhardening stagnation[J]. International Journal of Plasticity，2002，18(5):661-686.
[24] PIAO K，LEE J K，KIM J H，et al. A sheet tension/compression test for elevated temperature[J]. International Journal of Plasticity，2012，38:27-46.
[25] STRICKER M，WEYGAND D，GUMBSCH P. Irreversibility of dislocation motion under cyclic loading due to strain gradients [J]. Scripta Materialia，2017，129:69-73.

7075铝合金超低温变形行为与回弹预测研究

Study on the Deformation Behavior and Springback Prediction of 7075 Aluminum Alloy at Cryogenic Temperature

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	石楠楠, 高海涛, 唐乐千, KONG Charlie, 喻海良. 深冷轧制与深冷处理7075铝合金带材疲劳裂纹扩展性能研究[J]. 机械工程学报, 2026, 62(6): 47-64.
[2]	束学道, 陈宇森, 王英, 代月晨, 左锦荣, 张庆东. 铝合金空心轴形孔同步成形协调机制与智能调控[J]. 机械工程学报, 2026, 62(6): 121-131.
[3]	胡志力, 芦俊杰, 魏鹏飞, 华林. Al-Zn-Mg-Cu合金预强化高效精确热冲压变形规律与力学性能研究[J]. 机械工程学报, 2025, 61(6): 160-173.
[4]	米高阳, 蒋熠鸣, 王春明, 张铭洋, 胡溢洋, 肖永康, 翟春成, 欧阳求保. 激光摆动焊接7075铝合金接头的成形、组织和力学性能[J]. 机械工程学报, 2025, 61(4): 86-95.
[5]	湛利华, 赵帅, 杨有良, 陈赞冲, 谢豪, 刘长志, 鄢东洋. 基于SPSO-BP神经网络的带筋壁板蠕变成形高精度快速回弹预测[J]. 机械工程学报, 2025, 61(20): 81-90.
[6]	韩龙帅, 官英平, 韩赟, 李学涛, 邱木生, 郑学斌. 不同硬化模型对CP1180钢在大变形下的适用性评估[J]. 机械工程学报, 2025, 61(18): 118-126.
[7]	姚梦佳, 王睿乾, 刘伟. 2195铝锂合金超低温变形各向异性行为及组织演变规律[J]. 机械工程学报, 2025, 61(14): 73-80.
[8]	郝永刚, 金晓月, 刘伟, 王睿乾. 2219铝合金搅拌摩擦拼焊板超低温变形与组织性能研究[J]. 机械工程学报, 2025, 61(14): 91-98.
[9]	郑学斌, 韩龙帅, 李学涛, 鄂宏伟, 吴向东, 万敏. DP780双相钢U弯回弹预测影响因素研究[J]. 机械工程学报, 2024, 60(6): 197-206.
[10]	刘承尚, 陈锐, 李芳, 王萌, 徐戊矫. 基于改进遗传算法的超高强钢硬化模型参数确定及折弯回弹预测[J]. 机械工程学报, 2024, 60(12): 240-249.
[11]	王鹏, 周均元, 李宏伟, 向治宇. 考虑包辛格效应的特殊螺纹连接循环加载变形仿真分析[J]. 机械工程学报, 2022, 58(16): 21-32.
[12]	高嵩, 孙荧力, 李奇涵, 何童贵, 梁继才, 徐传伟. 非对称高铁列车车头窗口下梁的三维拉压复合弯曲精确成形[J]. 机械工程学报, 2021, 57(18): 222-228.
[13]	荣海, 盈亮, 胡平, 侯文彬. 基于连续介质损伤力学的7075铝合金高温成形极限理论预测与数值仿真[J]. 机械工程学报, 2020, 56(24): 51-60.
[14]	李小强, 董红瑞, 于长旺, 王海波, 杨岩峰, 宋炳毅, 万政, 李东升. 不同屈服准则与硬化模型对DP780双相高强钢拉延弯曲回弹预测影响规律研究[J]. 机械工程学报, 2020, 56(12): 42-55.
[15]	高嵩, 于长春, 梁继才, 李奇涵, 郝兆朋, 刘小勇, 赵希禄. 铝型材多点三维拉压复合弯曲成形工艺[J]. 机械工程学报, 2019, 55(20): 152-159.