45/316L复合管三辊斜轧组元金属变形规律研究

doi:10.3901/JME.2024.20.077

机械工程学报 ›› 2024, Vol. 60 ›› Issue (20): 77-87.doi: 10.3901/JME.2024.20.077

扫码分享

45/316L复合管三辊斜轧组元金属变形规律研究

季策^1,2,3,4, 吴晋^1,2, 李子轩^1,2, 王涛^1,2,3,4, 黄庆学^1,2,3

1. 太原理工大学机械与运载工程学院太原 030024;
2. 太原理工大学先进金属复合材料成形技术与装备教育部工程研究中心太原 030024;
3. 太原理工大学金属成形技术与重型装备全国重点实验室太原 030024;
4. 海安太原理工大学先进制造与智能装备产业研究院海安 226601)

收稿日期:2023-10-24 修回日期:2024-04-15 出版日期:2024-10-20 发布日期:2024-11-30
通讯作者: 王涛,男,1985年出生,博士,教授,博士研究生导师。主要研究方向为轧制工艺及设备、层状金属复合材料轧制复合机理。E-mail:twang@tyut.edu.cn
作者简介:季策,男,1990年出生,讲师。主要研究方向为层状金属复合材料高效制备技术与装备。E-mail:jice@tyut.edu.cn
基金资助:
国家自然科学基金(52205406，52205403，U22A20188);国家重点研发计划(2018YFA-0707300);中央引导地方科技发展资金(YDZX20191400002149);山西省基础研究计划青年科学研究(202303021223003，202203021212289，20210302124115);山西省“1331”工程重点创新团队建设计划和海安太原理工大学先进制造与智能装备产业研究院开放研究基金(2023HA-TYUTKFYF013)资助项目。

Study on Component Metal Deformation Law of 45/316L Cladding Tubes in Three-roll Skew Rolling Bonding Process

JI Ce^1,2,3,4, WU Jin^1,2, LI Zixuan^1,2, WANG Tao^1,2,3,4, HUANG Qingxue^1,2,3

1. College of Mechanical and Vehicle Engineering, Taiyuan University of Technology, Taiyuan 030024;
2. Engineering Research Center of Advanced Metal Composites Forming Technology and Equipment of Ministry of Education, Taiyuan University of Technology, Taiyuan 030024;
3. National Key Laboratory of Metal Forming Technology and Heavy Equipment, Taiyuan University of Technology, Taiyuan 030024;
4. Hai'an &Taiyuan University of Technology Advanced Manufacturing and Intelligent Equipment Industrial Research Institute, Hai'an 226601

Received:2023-10-24 Revised:2024-04-15 Online:2024-10-20 Published:2024-11-30

摘要/Abstract

摘要： 针对具有组元熔点高、变形抗力大、界面复合难等特征的高强耐蚀无缝金属复合管高效连续成形难题，提出了无缝金属复合管三辊斜轧复合工艺。基于ABAQUS软件建立了45/316L复合管三辊斜轧复合过程数值仿真模型，研究了不同减径量和初始组元金属壁厚占比时的减径率、减壁率、伸长率和组元金属壁厚占比等参数变化规律，最后通过试验成功制备了45/316L复合管，验证了仿真分析准确性。研究结果表明：在端部焊接、轧辊和芯棒多重约束作用下45碳钢管和316L不锈钢管实现被迫同步变形，组元金属壁厚占比基本不变，为实现目标尺寸规格精准控制奠定理论基础；拉剪试验表明拉剪断裂发生于45碳钢基体侧，侧弯试验后复合界面无开裂，复合界面实现高强冶金结合。因此，三辊斜轧复合工艺为实现高强耐蚀无缝金属复合管的组元厚比精确可控、界面高强冶金结合、高效连续近终成形提供了新思路。

关键词: 复合管, 斜轧, 变形规律, 层厚比, 冶金结合

Abstract: The three-roll skew rolling bonding process is proposed to solve the efficient continuous forming problems of seamless metal cladding tubes with high strength and corrosion resistance, which possess characteristics of high component melting point, large deformation resistance, and difficult interfacial bonding. Based on the ABAQUS software, a numerical simulation model is established for the three-roll skew rolling bonding process of 45/316L cladding tubes. The variation laws of the diameter reduction rate, wall reduction rate, elongation rate, component metal wall thickness ratio, etc. are studied under different diameter reduction rates and initial component metal wall thickness ratios. Finally, 45/316L cladding tubes were successfully prepared through the experiment, verifying the accuracy of the simulation analysis. The results show that 45 carbon steel and 316L stainless steel are forced to synchronously deform under multiple constraints of end welding, roll, and mandrel. The component metal wall thickness ratios are unchanged, laying a theoretical foundation for the accurate control of target size specifications. Tensile shear tests show that tensile shear fractures occur on the matrix of 45 carbon steel, and the bonding interface does not crack after the lateral bending test, proving that interfaces achieve high-strength metallurgical bonding. Therefore, the three-roll skew rolling bonding process provides a new method for realizing the precise control of component metal wall thickness, interfacial high-strength metallurgical bonding, and efficient continuous near-net forming of seamless metal cladding tubes with high strength and corrosion resistance.

Key words: cladding tube, skew rolling, deformation law, wall thickness ratio, metallurgical bonding

中图分类号:

TG335

季策, 吴晋, 李子轩, 王涛, 黄庆学. 45/316L复合管三辊斜轧组元金属变形规律研究[J]. 机械工程学报, 2024, 60(20): 77-87.

JI Ce, WU Jin, LI Zixuan, WANG Tao, HUANG Qingxue. Study on Component Metal Deformation Law of 45/316L Cladding Tubes in Three-roll Skew Rolling Bonding Process[J]. Journal of Mechanical Engineering, 2024, 60(20): 77-87.

参考文献

[1] XIONG J Y，LIANG W，DING Y，et al. Quantitative analysis of wall thinning of bimetallic clad steel tube based on pulsed eddy current[J]. Process Safety Progress，2022，41：118-128.
[2] GAO Z H，HAN B，LI L Y，et al. Numerical simulation of residual stress in post internal-welding process of bimetal composite pipe and optimization of welding sequence[J]. International Journal of Pressure Vessels and Piping，2022，199：104730.
[3] QIAN L Y，CUI Z G，SUN C Y，et al. Investigation of deformation compatibility and power consumption during KOBO extrusion of bimetallic composite tube[J]. The International Journal of Advanced Manufacturing Technology，2022，118(9)：3477-3486.
[4] 季策，许石民，黄华贵. 金属包覆材料固-液铸轧复合技术研究进展[J]. 精密成形工程，2021，13(6)：12-22. JI Ce，XU Shimin，HUANG Huagui. Research progress of solid-liquid cast-rolling bonding technology for metal cladding materials[J]. Journal of Netshape Forming Engineering，2021，13(6)：12-22.
[5] ZHANG S X，MA Q Z，XU C F，et al. Root cause analysis of liner collapse and crack of bimetal composite pipe used for gas transmission[J]. Engineering Failure Analysis，2022，132：105942.
[6] JIANG S Y，ZHANG Y Q，ZHAO Y N，et al. Investigation of interface compatibility during ball spinning of composite tube of copper and aluminum[J]. The International Journal of Advanced Manufacturing Technology，2017，88(1)：683-690.
[7] JIN K，YUAN Q W，TAO J，et al. Analysis of the forming characteristics for Cu/Al bimetal tubes produced by the spinning process[J]. The International Journal of Advanced Manufacturing Technology，2019，101(1)：147-155.
[8] ZHAN L Q，WANG G，YANG J L，et al. Study on gas bulging forming and contradictive cooling bonding of AZ31/Al7475 bimetal composite tube[J]. Journal of Materials Engineering and Performance，2020，29(7)：4652-4658.
[9] GUO X Z，YU Y H，TAO J，et al. Maximum residual contact stress in spinning process of SS304/20 bimetallic pipe[J]. The International Journal of Advanced Manufacturing Technology，2020，106(7)：2971-2982.
[10] JIANG L，LUO N，LIANG H L，et al. Microstructure and texture distribution in the bonding interface of Cu/Al composite tube fabricated by explosive welding[J]. The International Journal of Advanced Manufacturing Technology，2022，123(9)：3021-3031.
[11] DANG H Q，YU H P. Improving the quality of Al-Fe tube joints manufactured via magnetic pulse welding using an inclined-wall field shaper[J]. Journal of Manufacturing Processes，2022，73：78-89.
[12] NAQIBI M F，ELYASI M，AVAL H J，et al. Theoretical and experimental studies on fabrication of two-layer aluminum−copper pipe by friction stir additive manufacturing[J]. Transactions of Nonferrous Metals Society of China，2021，31(12)：3643–58.
[13] JI C，HUANG H G，MENG K. Influence of process layouts of multi-roll solid-liquid cast-rolling bonding process on circumferential performance uniformity during fabricating metal cladding materials[J]. Journal of Materials Processing Technology，2022，301：117444.
[14] 黄华贵，季策，杜凤山. 双金属复合管固-液铸轧复合轧制力模型研究[J]. 机械工程学报，2017，53(10)：10-17. HUANG Huagui，JI Ce，DU Fengshan. Research on cast-rolling force calculation model in solid-liquid cast-rolling bonding (SLCRB) process of bimetallic clad pipe[J]. Journal of Mechanical Engineering，2017，53(10)：10-17.
[15] LI Z X，REZAEI S，WANG T，et al. Recent advances and trends in roll bonding process and bonding model: A review[J]. Chinese Journal of Aeronautics，2023，36(4)：36-74.
[16] 任忠凯，郭雄伟，李宁，等. 脉冲电流对TA1/304复合板结合性能的改性机制研究[J]. 机械工程学报，2022，58(6)：62-72. REN Zhongkai，GUO Xiongwei，LI Ning，et al. Study on the modification mechanism of pulse current on the bonding properties of TA1/304 composite plate[J]. Journal of Mechanical Engineering，2022，58(6)：62-72.
[17] 王涛，齐艳阳，刘江林，等. 金属层合板轧制复合工艺国内外研究进展[J]. 哈尔滨工业大学学报，2020，52(6)：42-56. WANG Tao，QI Yanyang，LIU Jianglin，et al. Research progress of metal laminates roll bonding process at home and abroad[J]. Journal of Harbin Institute of Technology，2020，52(6)：42-56.
[18] CHANG D X，WANG P. Effect of interface on microstructure and mechanical properties of Cu/Al laminated composite produced by asymmetrical roll bonding and annealing[J]. Rare Metal Materials and Engineering，2020，49(1)：85-92.
[19] 肖宏，许朋朋，祁梓宸，等. 感应加热异温轧制制备钢/铝复合板[J]. 金属学报，2020，56(2)：231-239. XIAO Hong，XU Pengpeng，QI Zichen，et al. Preparation of steel/aluminum laminated composites by differential temperature rolling with induction heating[J]. Acta Metallurgica Sinica，2020，56(2)：231-239.
[20] 陈宇，刘文文，王涛，等. 预制波纹工艺对钢/铝/铝合金复合板界面影响机制研究[J]. 机械工程学报，2023，59(8)：74-82. CHEN Yu，LIU Wenwen，WANG Tao，et al. Study on influence mechanism of prefabricated corrugation process on interface of steel/aluminum/aluminum alloy laminated plate[J]. Journal of Mechanical Engineering，2023，59(8)：74-82.
[21] SHUAI M R，YE L P，LIU X，et al. Continuous reducing and sizing process of hot rolled steel-copper clad tube[J]. Materials Research Express，2019，6(5)：055807.
[22] HE Z L，CHU Z B，SHUANG Y H，et al. The bonding mechanism and experimental verification of pilger hot rolling clad tube[J]. Advances in Materials Science and Engineering，2020，2689370：1-12.
[23] 胡建华，李靖，王仕杰，等. 双金属复合管热连轧有限元模拟及极限减壁量确定[J]. 塑性工程学报，2022，29(9)：102-107. HU Jianhua，LI Jing，WANG Shijie，et al. Finite element simulation of bimetallic composite pipe hot continuous rolling and determination of limit wall reduction[J]. Journal of Plasticity Engineering，2022，29(9)：102-107.
[24] 祁梓宸，余超，肖宏，等. 异温轧制制备钛/铝复合板的变形协调性与复合性能[J]. 中国有色金属学报，2018，28(6)：1120-1127. QI Zichen，YU Chao，XIAO Hong，et al. Deformation coordination compatibility and bonding properties of Ti/Al composite plates prepared by different temperature rolling[J]. The Chinese Journal of Nonferrous Metals，2018，28(6)：1120-1127.

45/316L复合管三辊斜轧组元金属变形规律研究

Study on Component Metal Deformation Law of 45/316L Cladding Tubes in Three-roll Skew Rolling Bonding Process

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 11

编辑推荐

Metrics

本文评价

[1]	张婷婷, 许振波, 王艳, 卞功波, 王涛, 王文先. 高频脉冲电流辅助镁/铝合金一步轧焊复合板制备及界面接合机理[J]. 机械工程学报, 2024, 60(4): 305-315.
[2]	陈宇, 刘文文, 王涛, 申宏卓, 陈科, 张斌. 预制波纹工艺对钢/铝/铝合金复合板界面影响机制研究[J]. 机械工程学报, 2023, 59(8): 74-82.
[3]	胡志力, 范新欣, 华林. 高强铝合金FSW拼焊板变形规律与成形技术[J]. 机械工程学报, 2020, 56(6): 206-212.
[4]	刘明, 陈书赢, 马国政, 邢志国, 何鹏飞, 王海斗, 霍明亮. 热喷涂涂层/基体异质界面结合强度优化理论与方法现状研究[J]. 机械工程学报, 2020, 56(10): 64-77.
[5]	黄华贵, 季策, 杜凤山. 双金属复合管固-液铸轧复合轧制力模型研究[J]. 机械工程学报, 2017, 53(10): 10-17.
[6]	胡正寰;杨翠苹;王宝雨. 我国轴类零件轧制技术进展[J]. , 2012, 48(18): 7-12.
[7]	李文钊;边秀房. 铝铁复合铸造界面金相研究[J]. , 2011, 47(16): 67-72.
[8]	吴伟辉;杨永强. 选区激光熔化快速成形系统的关键技术[J]. , 2007, 43(8): 175-180.
[9]	王学生;王如竹;李培宁. 自紧密封不锈钢衬里复合管液压胀合研究[J]. , 2004, 40(5): 72-76.
[10]	双远华;赖明道;张中元. 斜轧穿孔过程金属流动的有限元模拟[J]. , 2004, 40(3): 140-144,.
[11]	傅铭旺;罗子健. 粘塑性挤压成形变形规律研究[J]. , 1994, 30(1): 82-88.