后端设置扰流板对圆柱流场与气动噪声影响

doi:10.3901/JME.2024.12.287

机械工程学报 ›› 2024, Vol. 60 ›› Issue (12): 287-300.doi: 10.3901/JME.2024.12.287

扫码分享

后端设置扰流板对圆柱流场与气动噪声影响

朱剑月^1,2, 袁咏祎^1,2, 陈羽², 徐俊起³

1. 同济大学铁道与城市轨道交通研究院上海 201804;
2. 同济大学汽车学院上海 201804;
3. 同济大学磁浮交通工程技术研究中心上海 201804

收稿日期:2023-06-30 修回日期:2024-02-10 出版日期:2024-06-20 发布日期:2024-08-23
作者简介:朱剑月,男,1973年出生,博士,副教授,博士研究生导师。主要研究方向为高速列车空气动力学与气动噪声。E-mail:zhujianyue@tongji.edu.cn;陈羽(通信作者),男,1986年出生,博士,讲师,硕士研究生导师。主要研究方向为列车空气动力学。E-mail:chen.yu@tongji.edu.cn
基金资助:
新能源汽车及动力系统国家工程研究中心、国家自然科学基金(52232013，51875411)和上海市地面交通工具空气动力与热环境模拟重点实验室资助项目。

Influence of Attached Splitter Plate on the Flow and Flow-induced Noise Generated from Circular Cylinder

ZHU Jianyue^1,2, YUAN Yongyi^1,2, CHEN Yu², XU Junqi³

1. Institute of Rail Transit, Tongji University, Shanghai 201804;
2. School of Automobile, Tongji University, Shanghai 201804;
3. Maglev Transportation Engineering R&D Center, Tongji University, Shanghai 201804

Received:2023-06-30 Revised:2024-02-10 Online:2024-06-20 Published:2024-08-23

摘要/Abstract

摘要： 采用延迟分离涡模型进行数值模拟，基于涡声理论和声类比方法，计算分析雷诺数Re=6×10⁴下后端设置不同长度扰流板(不大于圆柱直径)的圆柱杆件周围流场与气动噪声特性，并与具有相同特征长度的普通圆柱杆件工况进行对比。圆柱杆件远场气动噪声计算值与声学风洞测试结果的频谱曲线吻合良好，验证数值模拟的准确性。结果表明，圆柱后端加设扰流板后，流动分离形成的涡脱落发展被限制在扰流板两侧，使得类圆柱杆件尾迹内分离剪切层长度增加，涡运动耗散增强，近壁面涡旋波动强度和尾迹内规则涡脱落强度减弱，降低几何体周围近场四极子气动噪声源强度，同时减小类圆柱杆件气动力脉动和阻力平均值，降低涡脱落诱发气动噪声的谐频峰值，有效降低远场偶极子噪声的声压级幅值，取得较好的气动噪声降噪效果。

关键词: 圆柱, 扰流板, 气动噪声, 流场特性, 噪声控制

Abstract: The characteristics of flow and aerodynamic noise generated around a circular cylinder using an attached splitter plate with different lengths (no more than cylinder diameter) have been studied and compared with the circular cylinder case of the same characteristic dimensions at a Reynolds number of 6×10⁴ based on the theory of vortex sound and acoustic analogy approach after the flow is simulated using the delayed detached-eddy model. The calculated spectra of far-field aerodynamic noise agree well with the anechoic wind-tunnel experiments for the circular cylinder case, verifying the accuracy of the numerical simulations. Results show that the developing of the vortex shedding induced from the flow separations is limited along two sides of the splitter plate after it is attached at the rear of the cylinder. The separated shear layer developed in the wake of cylindrical bars is elongated and the dissipation of vortex motion is strengthened. The vortex undulation close to the walls and regular vortex shedding in the wake are mitigated. Thus the strength of near-field quadrupole sound source is reduced. Meanwhile the aerodynamic force fluctuation and mean drag are decreased. Consequently the harmonic peak values of flow-induced noise generated from the vortex shedding are reduced effectively and the corresponding amplitude of sound pressure level of far-field dipole sound source is decreased. Thereby a good aerodynamic noise reduction effect is achieved for a circular cylinder with an attached splitter plate.

Key words: circular cylinder, splitter plate, aerodynamic noise, flow behaviour, noise control

中图分类号:

O355

朱剑月, 袁咏祎, 陈羽, 徐俊起. 后端设置扰流板对圆柱流场与气动噪声影响[J]. 机械工程学报, 2024, 60(12): 287-300.

ZHU Jianyue, YUAN Yongyi, CHEN Yu, XU Junqi. Influence of Attached Splitter Plate on the Flow and Flow-induced Noise Generated from Circular Cylinder[J]. Journal of Mechanical Engineering, 2024, 60(12): 287-300.

参考文献

[1] ZDRAVKOVICH M M. Flow around circular cylinders，Volume 1. A comprehensive guide through flow phenomena，experiments，applications，mathematical models，and computer simulations[M]. Oxford：Oxford University Press，1997.
[2] 黄为民，游晖，林向群. 前驻点加热圆柱绕流场的试验研究[J]. 上海机械学院学报，1994，16(3)：99-102. HUANG Weimin，YOU Hui，LIN Xiangqun. Experimental study about flow around a circular cylinder with heating front stationary point[J]. Journal of Shanghai Institute of Mechanical Engineering，1994，16(3)：99-102.
[3] 谢杰，许劲松，郁程. 圆柱扰流的流动分离控制[J]. 哈尔滨工程大学学报，2011，32(4)：401-406. XIE Jie，XU Jinsong，YU Cheng. A flow separation control on cylinder flow[J]. Journal of Harbin Engineering University，2011，32(4)：401-406.
[4] 周本谋，范宝春，陈志华，等. 流体边界层上电磁力的控制效应研究[J]. 力学学报，2004，36(4)：472-478. ZHOU Benmou，FAN Baochun，CHEN Zhihua，et al. Flow control effects of electromagnetic force in the boundary layer[J]. Chinese Journal of Theoretical and Applied Mechanics，2004，36(4)：472-478.
[5] 侯龙锋，高超，郑博睿，等. 等离子体流动分离控制的数值模拟[J]. 科学技术与工程，2011，11(10)：2249-2254. HOU Longfeng，GAO Chao，ZHENG Borui，et al. Simulation of plasma actuators in flow separation control[J]. Science Technology and Engineering，2011，11(10)：2249-2254.
[6] NISHIMURA M，GOTO T. Aerodynamic noise reduction by pile fabrics[J]. Fluid Dynamics Research，2010，42(1)：015003.
[7] KING W F，PFIZENMAIER E. An experimental study of sound generated by flows around cylinders of different cross-section[J]. Journal of Sound and Vibration，2009，328：318-337.
[8] FUJISAWA N，HIRABAYASHI K，YAMAGATA T. Aerodynamic noise reduction of circular cylinder by longitudinal grooves[J]. Journal of Wind Engineering & Industrial Aerodynamics，2020，199：104129.
[9] 段志强. 低雷诺数下尾部隔板影响圆柱扰流的数值研究[D]. 重庆：重庆大学，2012. DUAN Zhiqiang. A numerical investigation on fluid flow past a circular cylinder with splitter plate at low Reynolds number[D]. Chongqing：Chongqing University，2012.
[10] POWELL A. Theory of vortex sound[J]. Journal of the Acoustical Society of America，1964，36(1)：177-195.
[11] HOWE M S. Theory of vortex sound[M]. Cambridge：Cambridge University Press，2003.
[12] WANG M，FREUND J B，LELE S K. Computational prediction of flow-generated sound[J]. Annual Review of Fluid Mechanics，2006，38：483-512.
[13] SPALART P R，DECK S，SHUR M L，et al. A new version of detached-eddy simulation，resistant to ambiguous grid densities[J]. Theoretical and Computational Fluid Dynamics，2006，20：181-195.
[14] FFOWCS-WILLIAMS J E，HAWKINGS D L. Sound radiation from turbulence and surfaces in arbitrary motion[J]. Philosophical Transactions of the Royal Society of London，1969，264：321-342.
[15] LIGHTHILL M J. On sound generation aerodynamically. General theory[J]. Proceedings of the Royal Society of London，Series A，Mathematical and Physical Sciences，1952，211：564-587.
[16] FARASSAT F. Derivation of formulations 1 and 1A of Farassat[R]. NASA/TM-214853，2007.
[17] BRENTNER K S，FARASSAT F. Modelling aerodynamically generated sound of helicopter rotors[J]. Progress in Aerospace Sciences，2003，39：83-120.
[18] ZHU J Y，HU Z W，THOMPSON D J. Flow behaviour and aeroacoustic characteristics of a simplified high-speed train bogie[J]. Proceedings of the Institution of Mechanical Engineers Part F：Journal of Rail and Rapid Transit，2016，230(7)：1642-1658.
[19] ZHU J Y. Aerodynamic noise of high-speed train bogies[D]. Southampton：University of Southampton，2015.

后端设置扰流板对圆柱流场与气动噪声影响

Influence of Attached Splitter Plate on the Flow and Flow-induced Noise Generated from Circular Cylinder

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张风利, 张荣荣, 罗秋丽, 张亚东, 李兵, 郭慧. 某SUV镂空扰流板气动噪声机理分析及降噪研究[J]. 机械工程学报, 2024, 60(6): 398-408.
[2]	魏永峭, 张晋, 王少江, 漆小虎, 郭瑞, 杨海江. 变双曲圆弧齿线圆柱齿轮传动界面磨损规律及敏感性分析[J]. 机械工程学报, 2024, 60(5): 81-94.
[3]	贾康, 王浩, 任东旭, 洪军. 一种圆柱型车齿刀的安装模型及无干涉设计方法[J]. 机械工程学报, 2024, 60(5): 352-361.
[4]	刘明良, 唐颀, 田小永, 刘腾飞, 秦滢杰, 李涤尘. 连续纤维增强加筋圆柱壳回转3D打印工艺及其轴压性能研究[J]. 机械工程学报, 2024, 60(15): 283-290.
[5]	查俊, 张会杰. 竖直静压圆柱导轨系统运动误差理论模型研究[J]. 机械工程学报, 2023, 59(9): 116-124.
[6]	王鹏, 杨策, 郭琢, 林家春, 石照耀. 渐开线直齿圆柱齿轮增速传动和减速传动齿根弯曲应力对比分析[J]. 机械工程学报, 2023, 59(5): 130-141.
[7]	张雷雷, 赵延治, 赵铁石. 并联机构瞬轴面研究进展[J]. 机械工程学报, 2023, 59(21): 131-146.
[8]	孙朱俊, 许斌, 黄典贵. 前缘涡振圆柱对翼型气动性能的影响[J]. 机械工程学报, 2022, 58(6): 242-252.
[9]	张文, 丁雨林, 陈咏华, 孙振国. 圆柱形钢制构件表面爬壁机器人姿态估计方法[J]. 机械工程学报, 2022, 58(5): 1-7.
[10]	郝旭, 李宁, 于长鑫, 翟敬宇. 考虑热效应的圆柱滚子轴承内外圈位移及滚道应力特性分析[J]. 机械工程学报, 2022, 58(5): 151-160.
[11]	高红, 肖杰. 波浪能捕获浮体对能量转化系统特性的影响[J]. 机械工程学报, 2022, 58(16): 360-369.
[12]	朱凌云, 苟向锋, 柴长银, 祁常君, 石建飞, 沈佳志. 基于Seebeck效应的齿面温度测量研究[J]. 机械工程学报, 2022, 58(15): 263-273.
[13]	卢炽华, 孙孟雷, 刘志恩, 陈弯, 李晓龙. 主动冲击噪声控制自适应算法综述及综合性能分析[J]. 机械工程学报, 2022, 58(13): 101-118.
[14]	蒋书运, 祝进波. 静压圆柱导轨系统静态刚度理论模型研究[J]. 机械工程学报, 2021, 57(23): 97-105.
[15]	陈志平, 焦鹏, 马赫, 顾亚楠, 葛鹏. 基于初始缺陷敏感性的轴压薄壁圆柱壳屈曲分析研究进展[J]. 机械工程学报, 2021, 57(22): 114-129.