基于复合泄漏通道模型的O型圈密封泄漏率计算方法研究

doi:10.3901/JME.2023.11.232

机械工程学报 ›› 2023, Vol. 59 ›› Issue (11): 232-241.doi: 10.3901/JME.2023.11.232

扫码分享

基于复合泄漏通道模型的O型圈密封泄漏率计算方法研究

王祺德^1,2, 刘达新^1,2, 刘振宇^1,2, 谭建荣^1,2

1. 浙江大学计算机辅助设计与图形学国家重点实验室杭州 310027;
2. 浙江大学设计工程及数字孪生浙江省工程研究中心杭州 310027

收稿日期:2022-06-11 修回日期:2023-02-09 出版日期:2023-06-05 发布日期:2023-07-19
通讯作者: 刘达新(通信作者),男,1982年出生,博士,讲师。主要研究方向为复杂装备数字样机与仿真、产品密封控制与质量检测等。E-mail:liudx@zju.edu.cn
作者简介:王祺德,男,1995年出生,博士研究生。主要研究方向为复杂装备数字化设计与装配、液压多路阀密封控制等。E-mail:btwqd@zju.edu.cn;刘振宇,男,1974年出生,博士,教授,博士研究生导师。主要研究方向为复杂装备数字化设计与制造、数字孪生与混合现实等。E-mail:liuzy@zju.edu.cn;谭建荣,男,1954年出生,博士,教授,博士研究生导师,中国工程院院士,中国机械工程学会副理事长。主要研究方向为复杂装备数字化设计与制造、机械设计及理论。E-mail:egi@zju.edu.cn
基金资助:
国家重点研发计划(2018YFB2001201)和国家自然科学基金(52075480，51935009)资助项目

A Leakage Rate Calculation Method for O-ring Seal Based on Compound Leakage Channel Model

WANG Qide^1,2, LIU Daxin^1,2, LIU Zhenyu^1,2, TAN Jianrong^1,2

1. State Key Laboratory of CAD & CG, Zhejiang University, Hangzhou 310027;
2. Engineering Research Center for Design Engineering and Digital Twin of Zhejiang Province, Zhejiang University, Hangzhou 310027

Received:2022-06-11 Revised:2023-02-09 Online:2023-06-05 Published:2023-07-19

摘要/Abstract

摘要： O型圈密封作为机械结构中最常见的密封形式之一，实现其密封泄漏率的准确定量计算进而保障其密封性能，对机械产品和装备整体的安全性、可靠性和环境保护性等具有重要意义。现有的O型圈泄漏率计算方法难以在计算准确度与模型复杂度间达到很好的平衡。针对这一问题，提出了一种基于复合泄漏通道模型的O型圈泄漏率计算方法。复合泄漏通道模型通过对粗糙表面轮廓三角峰均一化排列，将O型圈与粗糙表面间的泄漏通道定义为三角形通道和梯形通道两种典型形式。相比现有方法通过单一几何体对泄漏通道建模，复合泄漏通道模型引入粗糙表面三角峰统计参数对泄漏通道进行表征，充分反映了表面形貌特征对通道形式与泄漏率的影响。局部密封单元的泄漏仿真实验表明，复合泄漏通道模型相比经典的Roth模型具有更好的计算准确性。将该方法应用于一种典型的O型圈密封结构，设计并实施了泄漏率测量实验，实验结果表明不同O型圈压缩率下泄漏率计算结果的平均相对误差不超过15%，验证了提出的方法在实际应用场景下的有效性。

关键词: O型圈, 密封, 泄漏通道, 粗糙表面, 泄漏率

Abstract: O-ring seal is one of the most common sealing forms in mechanical structures. Accurate calculation of leakage rate of O-ring seal helps to ensure its sealing performance, which is important for the safety, reliability and environmental protection of mechanical products and equipment. Existing O-ring leakage rate calculation methods are difficult to achieve a good balance between calculation accuracy and model complexity. To solve this problem, a method for leakage rate calculation of O-ring seal based on the compound leakage channel model is proposed. Compound leakage channel model defines the leakage channel as two typical forms, including triangular channel and trapezoidal channel, by uniformly arranging the triangular peaks of rough surface profile. Compared with the existing methods which model the leakage channel with a single geometry, the compound leakage channel model introduces statistical parameters of rough surface triangular peaks to characterize the leakage channel, which fully reflects the influence of the surface topography characteristics on the channel form and the leakage rate. The leakage simulation experiment of the local sealing unit shows that the compound leakage channel model has the better calculation accuracy than the traditional Roth model. Finally, the proposed method is applied to a typical O-ring seal structure, and the leakage rate measurement experiment is designed and implemented. The experiment results show that the average relative error of the leakage rate under different O-ring compression rate does not exceed 15%. The effectiveness of the proposed method in real application cases is verified.

Key words: O-ring, seal, leakage channel, rough surface, leakage rate

中图分类号:

TB42

王祺德, 刘达新, 刘振宇, 谭建荣. 基于复合泄漏通道模型的O型圈密封泄漏率计算方法研究[J]. 机械工程学报, 2023, 59(11): 232-241.

WANG Qide, LIU Daxin, LIU Zhenyu, TAN Jianrong. A Leakage Rate Calculation Method for O-ring Seal Based on Compound Leakage Channel Model[J]. Journal of Mechanical Engineering, 2023, 59(11): 232-241.

参考文献

[1] 彭旭东，王玉明，黄兴，等. 密封技术的现状与发展趋势[J]. 液压气动与密封，2009，29(4):4-11. PENG Xudong，WANG Yuming，HUANG Xing，et al. State-of-the-Art and future development of sealing technology[J]. Hydraulics Pneumatics & Seals，2009，29(4):4-11.
[2] PERSSON B N J，YANG C. Theory of the leak-rate of seals[J]. Journal of Physics:Condensed Matter，2008，20(31):315011.
[3] ZHANG Feikai，LIU Jianhua，DING Xiaoyu，et al. An approach to calculate leak channels and leak rates between metallic sealing surfaces[J]. Journal of Tribology，2017，139(1):011708.
[4] PÉREZ-RÀFOLS F，LARSSON R，ALMQVIST A. Modelling of leakage on metal-to-metal seals[J]. Tribology International，2016，94:421-427.
[5] PÉREZ-RÀFOLS F，LARSSON R，LUNDSTRÖM S，et al. A stochastic two-scale model for pressure-driven flow between rough surfaces[J]. Proceedings of the Royal Society A:Mathematical，Physical and Engineering Sciences，2016，472(2190):20160069.
[6] BOTTIGLIONE F，CARBONE G，MANGIALARDI L，et al. Leakage mechanism in flat seals[J]. Journal of Applied Physics，2009，106(10):104902.
[7] TIWARI A，DOROGIN L，TAHIR M，et al. Rubber contact mechanics:Adhesion，friction and leakage of seals[J]. Soft Matter，2017，13(48):9103-9121.
[8] 史建成，刘检华，杨志猛，等. 基于栅格渗漏模型的静密封界面状态演变特性研究[J]. 机械工程学报，2016，52(7):104-113. SHI Jiancheng，LIU Jianhua，YANG Zhimeng，et al. On the phase transition characteristic of static sealing interface based on lattice leakage model[J]. Journal of Mechanical Engineering，2016，52(7):104-113.
[9] 嵇正波，孙见君，陆建花，等. 基于逾渗理论的机械密封界面静态泄漏预测方法[J]. 摩擦学学报，2017，37(6):734-742. JI Zhengbo，SUN Jianjun，LU Jianhua，et al. Predicting method for static leakage of contacting mechanical seals interface based on percolation theory[J]. Tribology，2017，37(6):734-742.
[10] ROTH A. The influence of the surface roughness on the specific leak rate of gasket seals[J]. Vacuum，1970，20(10):431-435.
[11] GEOFFROY S，PRAT M. On the leak through a spiral-groove metallic static ring gasket[J]. Journal of Fluids Engineering，2004，126(1):48-54.
[12] ROBBE-VALLOIRE F，PRAT M. A model for face-turned surface microgeometry:Application to the analysis of metallic static seals[J]. Wear，2008，264(11-12):980-989.
[13] 冯秀，顾伯勤. 金属垫片密封连接的泄漏率计算[J]. 化工学报，2010，61(5):1208-1212. FENG Xiu，GU Boqin. Leakage rate calculation of metallic gasket connections[J]. CIESC Journal，2010，61(5):1208-1212.
[14] SCARAGGI M，PERSSON B N J. General contact mechanics theory for randomly rough surfaces with application to rubber friction[J]. The Journal of Chemical Physics，2015，143(22):224111.
[15] GHOSH A，SADEGHI F. A novel approach to model effects of surface roughness parameters on wear[J]. Wear，2015，338-339:73-94.
[16] POGAČNIK A，KALIN M. How to determine the number of asperity peaks，their radii and their heights for engineering surfaces:A critical appraisal[J]. Wear，2013，300(1-2):143-154.
[17] ZHANG Bin，YU Min，YANG Huayong. Leakage analysis and ground tests of the O-type rubber ring seal applied in lunar sample return devices[J]. Proceedings of the Institution of Mechanical Engineers，Part G:Journal of Aerospace Engineering，2015，229(3):479-491.
[18] ZHANG Jie，XIE Jingxuan. Investigation of static and dynamic seal performances of a rubber O-ring[J]. Journal of Tribology，2018，140(4):042202.
[19] 吕祥奎，杨文健，许国良，等. 密封结构中粗糙表面特征对其气密性的影响[J]. 机械工程学报，2015，51(23):110-115. LÜ Xiangkui，YANG Wenjian，XU Guoliang，et al. The influence of characteristic of rough surface on gas sealing performance in seal structure[J]. Journal of Mechanical Engineering，2015，51(23):110-115.
[20] ZHANG Bin，HONG Haocen，YU Min，et al. Leakage analysis and ground tests of knife edge indium seal to lunar sample return devices[J]. Proceedings of the Institution of Mechanical Engineers，Part G:Journal of Aerospace Engineering，2019，233(6):2010-2022.
[21] 任晓，吴承伟，周平. 粗糙表面的气体密封性能研究[J]. 机械工程学报，2010，46(16):176-181. REN Xiao，WU Chengwei，ZHOU Ping. Gas sealing performance study of rough surface[J]. Journal of Mechanical Engineering，2010，46(16):176-181.
[22] YAO Xuefeng，LEI Yiming，XIONG Chao，et al. Experimental study of helium leakage parameters in flexible composite[J]. Journal of Applied Polymer Science，2010，116(6):3562-3568.
[23] ZHOU Chilou，ZHENG Jinyang，GU Chaohua，et al. Sealing performance analysis of rubber O-ring in high-pressure gaseous hydrogen based on finite element method[J]. International Journal of Hydrogen Energy，2017，42(16):11996-12004.
[24] WANG Runliang，LIU Jianhua，ZHANG Feikai，et al. An approach to evaluate the sealing performance of sealing structures based on multiscale contact analyses[J]. Journal of Computational Design and Engineering，2021，8(6):1433-1445.
[25] YANG Zhimeng，LIU Jianhua，DING Xiaoyu，et al. The effect of anisotropy on the percolation threshold of sealing surfaces[J]. Journal of Tribology，2019，141(2):022203.

基于复合泄漏通道模型的O型圈密封泄漏率计算方法研究

A Leakage Rate Calculation Method for O-ring Seal Based on Compound Leakage Channel Model

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	纪佳馨, 彭程, 项冲, 黄乐, 郭飞. 考虑变速条件的斯特封磨损寿命预测方法[J]. 机械工程学报, 2024, 60(3): 191-202.
[2]	钱萍, 刘鑫雨, 陈文华, 王哲, 郭明达. 电连接器用聚氨酯胶密封件贮存可靠性建模[J]. 机械工程学报, 2024, 60(20): 361-371.
[3]	刘跃, 黄民, 李永健, 安琪, 蒋杰. 大压差下热塑性迷宫密封泄漏特性研究[J]. 机械工程学报, 2024, 60(15): 194-204.
[4]	王娟, 刘美红, 祝世兴, 陈文博, 李遇贤, 孙军锋. 指尖密封结构参数的多目标混合教与学优化方法[J]. 机械工程学报, 2023, 59(9): 157-170.
[5]	胡琼, 肖洋, 卢迪, 曹志康, 王晓雷, 王衍, 武扬, 何一鸣. 微流道界面剪切对液膜密封空化流场特性的影响研究[J]. 机械工程学报, 2023, 59(9): 171-185.
[6]	雷俊杰, 刘美红, HU Xiangping, 王娟, 王学良. 基于分形理论的椭圆弧型指尖密封磨损特性分析[J]. 机械工程学报, 2023, 59(3): 144-157.
[7]	丁贤旺, 杨冰, 戎有鑫, 肖守讷, 阳光武, 朱涛. 基于W-M分形函数的轮轨滑动接触热响应分析[J]. 机械工程学报, 2023, 59(21): 356-366.
[8]	石嵩, 刘检华, 巩浩, 邵楠. 考虑粗糙表面接触配合的航空发动机多级转子装配误差传递建模[J]. 机械工程学报, 2023, 59(17): 208-219.
[9]	周炜, 赵岱岩, 唐进元. 一种基于峰谷数据映射的粗糙度轮廓重构方法[J]. 机械工程学报, 2023, 59(17): 268-278.
[10]	王衍, 谢雪非, 徐慧, 黄周鑫, 何一鸣, 杨怀石, 胡琼. 新型非接触式自冲击密封结构设计与性能分析[J]. 机械工程学报, 2023, 59(15): 204-215.
[11]	张彤, 李德才, 李艳文. 磁性液体密封与迷宫密封组合密封的结构设计及优化[J]. 机械工程学报, 2022, 58(9): 172-181.
[12]	袁芳, 王四棋, 李德才, 陈铎, 邸楠楠, 李文怡. 磁性液体密封新结构及耐压性能理论研究[J]. 机械工程学报, 2022, 58(3): 213-220.
[13]	崔颖, 于颖嘉, 张宏翔, 钟兢军. 基于多孔介质理论的双粗糙面金属静密封泄漏模型[J]. 机械工程学报, 2022, 58(21): 215-224.
[14]	王悦昶, 刘莹, 李鸿举. 粗糙表面仿真方法综述[J]. 机械工程学报, 2022, 58(19): 148-165.
[15]	马学忠, 孟祥铠. 瑞利台阶型机械密封端面环形槽的空化诱导机理分析[J]. 机械工程学报, 2022, 58(13): 166-174.