高速硬切削加工表面白层形成机理研究

doi:10.3901/JME.2015.23.182

机械工程学报 ›› 2015, Vol. 51 ›› Issue (23): 182-188.doi: 10.3901/JME.2015.23.182

扫码分享

高速硬切削加工表面白层形成机理研究

陈涛, 刘献礼, 李素燕, 李凯, 刘涛

哈尔滨理工大学机械动力工程学院哈尔滨 150080

收稿日期:2014-12-09 修回日期:2015-08-05 出版日期:2015-12-05 发布日期:2015-12-05
作者简介:陈涛，男，1979年出生，博士，教授。主要研究方向为高速/高效切削加工技术。 E-mail：chentao@hrbust.edu.cn
基金资助:
国家自然科学基金资助项目(51235003，51475125)

Mechanism of White Layer Formation on Machined Surface of High-speed Hard Machining

CHEN Tao, LIU Xianli, LI Suyan, LI Kai, LIU Tao

School of Mechanical and Power Engineering, Harbin University of Science and Technology, Harbin 150080

Received:2014-12-09 Revised:2015-08-05 Online:2015-12-05 Published:2015-12-05

摘要/Abstract

摘要： 白层是高速硬切削的特有现象，对加工表面完整性和零件的服役性能有着重要影响。针对高速硬切削加工表面白层问题，进行了对GCrl5淬硬轴承钢高速硬切削试验和表面白层测试，研究了不同切削条件下的白层形成机理，分析了切削速度和刀具磨损状态对白层特征的影响规律。分析结果表明，白层厚度随切削速度和后刀面磨损的增大而增大，而其分布的均匀性和连续性也将变差；切削速度和后刀面磨损的增加引起切削温度升高，导致加工表面快速淬火效应，使得白层厚度增大，其中切削速度的影响较为显著；在切削速度较低(100 m/min左右)时白层的形成机理主要为塑性变形，切削速度超过300 m/min则主要是马氏体相变所致，而在中间切削速度(200 m/min左右)时为2种机理的混合作用结果。

关键词: 白层, 高速切削, 加工表面, 硬切削

Abstract: White layer is a unique phenomenon of high-speed hard machining and has significant effects on machined surface integrity and service performance. Focusing on the white layer in high-speed hard machining, the high-speed hard cutting experiment of hardened GCrl5 bearing steel and white layer tests are conducted. The formation mechanism of white layer under various cutting conditions is investigated, and the influence of the cutting speed and flank wear on white layer’s features is studied. Analysis results show that the thickness of white layer increases with increasing cutting speed and flank wear, and the uniformity and continuity of the distribution of white layer decreases. Increasing cutting speed and flank wear will increase cutting temperature and result in rapid quenching effect of the machined surface, which causes an increasing of the thickness of white layer. The cutting speed has a more significant influence on the white layer than flank wear. The formation mechanism of white layer is plastic deformation at lower cutting speed (about 100 m/min), and is martensitic phase transformation when the cutting speed exceeds 300 m/min. The formation mechanism of white layer at midrange speed (about 200 m/min) is a hybrid effect of plastic deformation and martensitic phase transformation.

Key words: hard machining, high-speed machining, machined surface, white layer

陈涛, 刘献礼, 李素燕, 李凯, 刘涛. 高速硬切削加工表面白层形成机理研究[J]. 机械工程学报, 2015, 51(23): 182-188.

CHEN Tao, LIU Xianli, LI Suyan, LI Kai, LIU Tao. Mechanism of White Layer Formation on Machined Surface of High-speed Hard Machining[J]. Journal of Mechanical Engineering, 2015, 51(23): 182-188.

参考文献

[1] 陈涛, 刘献礼, 罗国涛. PCBN刀具切削淬硬钢时倒棱参数对切削过程的影响[J]. 农业机械学报, 2008, 39(11)：169-171，175. CHEN Tao，LIU Xianli，LUO Guotao. Effects of chamfered parameters on cutting processes in hard turning of hardened steel using PCBN cutting tools[J]. Transactions of the Chinese Society of Agricultural Machinery，2008，39(11)：169-171，175.
[2] 郭东明，孙玉文，贾振元. 高性能精密制造方法及其研究进展[J]. 机械工程学报，2014，50(11)：119-134. GUO Dongmin，SUN Yuwen，JIA Zhenyuan. Methods and research progress of high performance manufacturing[J]. Journal of Mechanical Engineering，2014，50(11)：119-134.
[3] 刘战强，吕绍瑜. 镍基粉末高温合金切削加工表面白层形成热-力耦合作用机理研究[J]. 机械工程学报，http：//www.cnki.net/kcms/detail/11.2187.TH.20140708.1339.014.html. LIU Zhanqiang，Lü Shaoyu. Thermo-mechanical coupling mechanisms for white layer formation on machined surface of powder metallurgical Nickel-based superalloy[J]. Journal of Mechanical Engineering，http：//www.cnki.net/kcms/detail/11.2187.TH.20140708.1339.014.html.
[4] 徐颖强，李娜娜，李万钟，等. 硬态切削工件表面白层厚度预测方法[J]. 机械工程学报，http：//www.cnki.net/kcms/detail/11.2187.TH.20140730.1039.016.htm. XU Yingqiang，LI Nana，LI Wanzhong，et al. Prediction method of the white layer thickness in hard cutting[J]. Journal of Mechanical Engineering，http：//www.cnki.net/kcms/detail/11.2187.TH.20140730.1039.016.htm.
[5] DING H，SHIN Y C. Multi-physics modeling and simulations of surface microstructure alteration in hard turning[J]. Journal of Materials Processing Technology，2013，213(6)：877-886.
[6] UMBRELLO D. Analysis of the white layers formed during machining of hardened AISI 52100 steel under dry and cryogenic cooling conditions[J]. International Journal of Advanced Manufacturing Technology，2013，64(5-8)：633-642.
[7] UMBRELLO D，ROTELLA G. Experimental analysis of mechanisms related to white layer formation during hard turning of AISI 52100 bearing steel[J]. Materials Science and Technology，2012，28(2)：205-212.
[8] HERBERTA C，AXINTEA D，HARDYB M，BROWN P D. Investigation into the characteristics of white layers produced in a nickel-based superalloy from drilling operations[J]. Machining Science and Technology，2012，16(1)：40-52.
[9] UMBRELLO D，JAYAL A D，CARUSO S，et al. Modeling of white and dark layer formation in hard machining of AISI 52100 bearing steel[J]. Machining Science and Technology，2010，14(1)：128-147.
[10] ATTANASIO A，UMBRELLO D，CAPPELLINI C，et al. Tool wear effects on white and dark layer formation in hard turning of AISI 52100 steel[J]. Wear，2012，286-287：98-107.
[11] VELDHUIS S C，DOSBAEVA G K，ELFIZY A，et al. Investigations of white layer formation during machining of powder metallurgical Ni-based ME 16 superalloy[J]. Journal of Materials Engineering and Performance，2010，19(7)：1031-1036.
[12] LIU G，TAN G，LI G，RONG Y. Multidisciplinary design optimization of a milling cutter for high speed milling of stainless steel[J]. International Journal of Advanced Manufacturing Technology，2013，68(9-12)：2431-2438.

[1]	岳晓明, 臧烁, 赵永华, 刘为东, 尹瀛月, 张勤河. 高品质超大深径比小孔电火花电解复合加工实验研究[J]. 机械工程学报, 2024, 60(9): 374-382.
[2]	毛聪, 孙鹏程, 唐伟东, 张明军, 罗源嫱, 胡永乐, 张德嘉, 唐昆, 管付如. 磨削白层特性及其与声发射信号的相关性[J]. 机械工程学报, 2023, 59(9): 349-359.
[3]	王敏杰, 王阳, 魏兆成, 段春争. 切削过程绝热剪切带的滑移线场研究[J]. 机械工程学报, 2022, 58(7): 284-294.
[4]	张振宇, 吴俊, 宋克峰, 郭昭志, 程军. 钛合金超微细磨削中磨削力和加工表面质量的研究[J]. 机械工程学报, 2022, 58(15): 75-91.
[5]	蒋生辉, 丁昊昊, 张翔, 彭建平, 王文健, 刘启跃, 郭俊. 基于磁巴克豪森噪声的钢轨白层无损检测研究[J]. 机械工程学报, 2021, 57(18): 49-57.
[6]	刘广鑫, 张定华, 姚倡锋. 钛合金切削表层微观组织研究进展[J]. 机械工程学报, 2021, 57(15): 231-245.
[7]	陈涛, 宋立星, 李素燕, 郭健, 刘献礼. 渐变强化刃刀具硬切削过程切屑流动和刀具磨损研究[J]. 机械工程学报, 2019, 55(19): 195-200.
[8]	张翔宇, 隋翯, 张德远, 姜兴刚, 吴瑞彪. 高速超声振动切削钛合金可行性研究[J]. 机械工程学报, 2017, 53(19): 120-127.
[9]	谷丽瑶, 王敏杰. 高速切削过程绝热剪切局部化断裂预测[J]. 机械工程学报, 2016, 52(5): 185-192.
[10]	徐颖强, 李娜娜, 李万钟, 郭彩虹. 硬态切削工件表面白层厚度预测方法[J]. 机械工程学报, 2015, 51(3): 182-189.
[11]	段春争, 张方圆, 孔维森. 干硬切削表面白层厚度的建模与预测[J]. 机械工程学报, 2015, 51(17): 194-202.
[12]	刘战强;吕绍瑜. 镍基粉末高温合金切削加工表面白层形成热-力耦合作用机理[J]. , 2014, 50(17): 186-193.
[13]	王敏杰;谷丽瑶. 高速切削过程绝热剪切局部化断裂判据[J]. , 2013, 49(1): 156-163.
[14]	汤爱民;周志雄;曾滔. 不等齿距三刃高速立铣刀的动平衡及设计[J]. , 2011, 47(13): 180-185.
[15]	张慧萍;李振加;刘二亮;魏国梁. 高速切削切屑折断界限变化规律[J]. , 2008, 44(5): 124-130.

高速硬切削加工表面白层形成机理研究

Mechanism of White Layer Formation on Machined Surface of High-speed Hard Machining

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价