Mo合金化处理对高锰钢磨损行为的影响

doi:10.3901/JME.2020.14.081

机械工程学报 ›› 2020, Vol. 56 ›› Issue (14): 81-90.doi: 10.3901/JME.2020.14.081

扫码分享

Mo合金化处理对高锰钢磨损行为的影响

马华¹, 陈晨¹, 王琳¹, 徐明², 畅国纪², 张福成^1,

1. 燕山大学亚稳材料制备技术与科学国家重点实验室秦皇岛 066004;
2. 中铁山桥集团有限公司秦皇岛 066205

收稿日期:2019-06-15 修回日期:2020-01-07 出版日期:2020-07-20 发布日期:2020-08-12
通讯作者: 张福成(通信作者),男,1964年出生,教授,博士研究生导师。主要研究方向为先进钢铁材料。E-mail:zfc@ysu.edu.cn
作者简介:马华,男,1992年出生,博士研究生。主要研究方向为铁路辙叉用钢。E-mail:mh@stumail.ysu.edu.cn
基金资助:
燕山大学博士基金资助项目（BL19007）。

Effect of Mo Alloying on Wear Behavior of Hadfield Steel

MA Hua¹, CHEN Chen¹, WANG Lin¹, XU Ming², CHANG Guoji², ZHANG Fucheng^1,

1. State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004;
2. China Railway Shanhaiguan Bridge Group Co., Ltd., Qinhuangdao 066205

Received:2019-06-15 Revised:2020-01-07 Online:2020-07-20 Published:2020-08-12

摘要/Abstract

摘要： 高锰钢是应用最广泛的耐磨材料之一，随着服役条件的不断恶化，传统高锰钢已经无法满足使用要求。对传统高锰钢Mn13进行Mo合金化处理获得Mn13Mo钢，通过金相显微镜、扫描电镜和EBSD等分析手段，对比研究Mn13Mo钢和Mn13钢在室温下的拉伸力学性能以及在相同磨损条件下的摩擦磨损行为。研究结果表明Mo能显著细化高锰钢晶粒，降低奥氏体层错能。在变形过程中Mn13Mo钢更易激活孪晶，形成更高密度的形变孪晶，展现出高强度和高的延伸率。在磨损试验中，Mn13Mo钢因其优异的加工硬化能力和塑性，形成高硬度的硬化表面和更深的应变层，展现出更佳的耐磨性能，并且在表面形成了硬化与磨损的动态平衡，磨损时间越长，其耐磨性优势更加明显。研究成果对高锰钢合金化处理有指导意义和参考价值。

关键词: 高锰钢, Mo, 合金化, 耐磨性

Abstract: Hadfield steel is one of the most widely used wear-resistant materials. However, with the deterioration of service conditions, the traditional high manganese steel is unable to meet the use requirments. Mo element is added in traditional Hadfield steel. Tensile properties and wear behaviors under same test conditions of Mo alloyed Hadfield steel (Mn13Mo steel), and traditional Hadfield steel (Mn13 steel), are studied by means of optical microscope, scanning electron microscope and electron backscattered diffraction (EBSD) technology, etc. Results show that Mo significantly refine the grain size of Hadfield steel. The strength and plasticity are improved obviously, with high deformation compatibility. This is mainly due to the reduction of stacking fault energy of Hadfield steel by Mo element, which made it easier to activate deformation twins to coordinate the plastic deformation. In the wear test, Mn13Mo steel, due to its excellent work hardening ability and plasticity, forms a hardened surface with high hardness and a deeper strain layer, showing a better wear resistance, and the surface has formed a dynamic balance between hardening and wear. With prolonging the wear time, the wear resistance of the Mn13Mo steel prevails. The results are of guiding significance and reference value for alloying treatment of Hadfield steel.

Key words: hadfield steel, Mo, alloying, wear resistance

中图分类号:

TG142

马华, 陈晨, 王琳, 徐明, 畅国纪, 张福成. Mo合金化处理对高锰钢磨损行为的影响[J]. 机械工程学报, 2020, 56(14): 81-90.

MA Hua, CHEN Chen, WANG Lin, XU Ming, CHANG Guoji, ZHANG Fucheng. Effect of Mo Alloying on Wear Behavior of Hadfield Steel[J]. Journal of Mechanical Engineering, 2020, 56(14): 81-90.

参考文献

[1] HADFIELD R A. Hadfield's manganese steel[J]. Science, 1888, 12(306):284-286.
[2] 张福成. 高锰钢辙叉材料研究进展[J]. 燕山大学学报, 2010(3):189-193. ZHANG Fucheng. Research progress of high manganese steel crossing materials[J]. Journal of Yanshan University, 2010(3);189-193.
[3] EFSTATHIOU C, SEHITOGLU H. Strain hardening and heterogen-eous deformation during twinning in Hadfield steel[J]. Acta Materialia, 2010, 58(5):1479-1488.
[4] LYCHAGIN D V, FILIPPOV A V, NOVITSKAIAO S, et al. Friction-induced slip band relief of hadfield steel single crystal oriented for multiple slip deformation[J]. Wear, 2017, 374-375:5-14.
[5] FENG X Y, ZHANG F C, YANG Z N, et al. Wear behaviour of nanocrystallised Hadfield steel[J]. Wear, 2013, 305(1-2):299-304.
[6] GOSS N P. The effect of cold rolling on the structure of Hadfield manganese steel[J]. Transactions of the American Society for Metals, 1945, 34:630-644.
[7] CANADINC D, SEHITOGLU H, MAIER H J. The role of dense dislocation walls on the deformation response of aluminum alloyed hadfield steel polycrystals[J]. Materials Science and Engineering:A, 2007, 454:662-666.
[8] LINDROOS M, APOSTOL M, HEINO V, et al. The deformation, strain hardening, and wear behavior of chromium-alloyed hadfield steel in abrasive and impact conditions[J]. Tribology Letters, 2015, 57(3):24.
[9] MOGHADDAM E G, VARAHRAM N, DAVAMI P. On the comparison of microstructural characteristics and mechanical properties of high-vanadium austenitic manganese steels with the Hadfield steel[J]. Materials Science and Engineering:A, 2012, 532:260-266.
[10] XIONG R, PENG H, WANG S, et al. Effect of stacking fault energy on work hardening behaviors in Fe-Mn-Si-C high manganese steels by varying silicon and carbon contents[J]. Materials & Design, 2015, 85:707-714.
[11] JUNJK J M, MICHAEL J R, PRASAD S V. The role of substrate plasticity on the tribological behavior of diamond-like nanocomposite coatings[J]. Acta Materialia, 2008, 56:1956-1966.
[12] BRESSAN J D, DAROS D P, SOKOLOWSKI A, et al Influence of hardness on the wear resistance of 17-4 PH stainless steel evaluated by the pin-on-disc testing[J]. Journal of Materials Processing Technolog, 2008, 205:353-359.
[13] LI J, LU Y, ZHANG H, et al. Effect of grain size and hardness on fretting wear behavior of Inconel 600 alloys[J]. Tribology International, 2015, 81:215-222.
[14] CHEN C, LV B, MA H, et al. Wear behavior and the corresponding work hardening characteristics of Hadfield steel[J]. Tribology International, 2018, 121:389-399.
[15] ABBASI M, KHEIRANDISH S, KHARRAZI Y, et al. On the comparison of the abrasive wear behavior of aluminum alloyed and standard Hadfield steels[J]. Wear, 2010, 268(1-2):202-207.
[16] ZHAO M C, HANAMURA T, QIU H, et al. Precipitation of carbontrides and their strengthening upon non-quench aging for micro-alloyed acicular ferrite pipeline steels[J]. Materials Transactions, 2005, 46(4):784-789.
[17] MIYATA K, KUSHIDA T, OMURA T, et al. Coarsening kinetics of multicomponent MC-type carbides in high-strength low-alloy steels[J]. Metallurgical and Materials Transactions A, 2003, 34(8):1565-1573.
[18] RAZAVI G R, RIAI M S, ZADEH H M. Effect of a Mo addition on the properties of high-Mn steel[J]. Materials and Technology, 2013, 47(5):611-614.
[19] ALI N, AMIRHOSSEIN K, PARVIZ D, et al. Effect of molybdenum on mechanical and abrasive wear properties of coating of as weld hadfield steel with flux-cored gas tungsten arc welding[J]. Journal of Alloys & Compounds, 2016, 659:262-269.
[20] DEARDO A J. Metallurgical basis for thermomechanical processing of microalloyed steels[J]. Ironmaking & Steelmaking, 2001, 28(2):138-144.
[21] TSUBAKINO H, AARONSON H I. Ferrite and carbide morphologies in and below the "bay region" of an Fe-0.19 Pct C-2.30 Pct Mo alloy[J]. Metallurgical Transactions A, 1987, 18(12):2047-2060.
[22] 周珍妮, 吴开明. 低合金钢中Mo溶质原子的拖曳效应[J]. 金属热处理, 2011, 36(11):1-6. ZHOU Zhenni, WU Kaiming. Solute drag-like effect of Mo in low alloy steels[J]. Heat Treatment of Metal, 2011, 36(11):1-6.
[23] SIMMONS J W. Overview:High-nitrogen alloying of stainless steels[J]. Materials Science & Engineering A, 1996, 207(2):159-169.
[24] EFSTATHIOU C, SEHITOGLU H. Strain hardening and heterogeneous deform during twinning in Hadfield steel[J]. Acta Materialia, 2010, 58:1479-1488.
[25] OWEN W S, GRUJICIC M. Strain aging of austenitic Hadfield manganese steel[J]. Acta Mater., 1999, 47(1):111-126.
[26] LIU F C, YANG Z N, ZHENG C L, et al. Simultaneously improving the strength and ductility of coarse-grained Hadfield steel with increasing strain rate[J]. Scripta Materialia, 2012, 66:431-434.
[27] BOUAZIZ O, ALLAIN S, SCOTT C P, et al. High manganese austenitic twinning induced plasticity steels:A review of the microstructure properties relationships[J]. Current Opinion in Solid State and Materials Science, 2011, 15:141-168.
[28] DE COOMAN B C, CHIN K G, KIM J. High Mn TWIP steels for automotive applications[M]//New Trends and Developments in Automotive System Engineering. In Tech, 2011:101-128.
[29] KANG S, JUNG J G, KANG M, et al. The effects of grain size on yielding, strain hardening, and mechanical twinning in Fe-18Mn-0.6 C-1.5 Al twinning-induced plasticity steel[J]. Materials Science and Engineering:A, 2016, 652:212-220.
[30] TANG J S C, KOCH C C. The hall-petch relationship in nanocrystalline iron produced by ball milling[J]. Scripta Metallurgica et Materialia, 1990, 24:1599-1604.
[31] YAN W L, FANG L, SUN K, et al. Effect of surface work hardening on wear behavior of Hadfield steel[J]. Materials Science and Engineering A, 2007, 460-461:542-549.
[32] DASTUR Y N, LESLIE W C. Mechanism of work hardening in Hadfield manganese steel[J]. Metallurgical & Materials Transactions A, 1981, 12(5):749-759.
[33] KARAMIS M B, ODABAS D. A simple approach to calculation of the sliding wear coefficient for medium carbon steels[J]. Wear, 1991, 151(1):23-34.
[34] TORO A, ZAPATA D, JARAMILLO J. Rolling contact and adhesive wear of bainitic and pearlitic steels in low load regime[J]. Wear, 2011, 271:393-399.
[35] ZHU T, GAO H J. Plastic deformation mechanism in nanotwinned metals:An insight from molecular dynamics and mechanistic modeling[J]. Scripta Materialia, 2012, 66(11):843-848.

Mo合金化处理对高锰钢磨损行为的影响

Effect of Mo Alloying on Wear Behavior of Hadfield Steel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	吴健文, 徐孟嘉, 范文艳, 陈浩宇, 江东航, 王振民. 钛合金快频脉冲柔性波形调制TIG焊接工艺[J]. 机械工程学报, 2020, 56(6): 102-109.
[2]	张昭, 谭治军, 李健宇, 苑红磊, 刘伟嵬. 铝合金搅拌摩擦搭接焊温度-再结晶-析出相-力学性能一体化数值模拟[J]. 机械工程学报, 2020, 56(6): 213-220.
[3]	王博文, 谢里阳, 樊富友, 马洪义, 赵丙峰, 李海洋. 考虑共因失效的折叠翼展开机构可靠度分析[J]. 机械工程学报, 2020, 56(5): 161-171.
[4]	赵飞飞, 曹开拓, 保宏, 高国明. Timoshenko梁的变形场重构及传感器位置优化[J]. 机械工程学报, 2020, 56(20): 1-11.
[5]	张伟, 闫志杰, 王睿, 李大赵, 康燕, 武中豪, 杨晓敏. Fe-1.3C-5Cr-0.4Mo-0.4V超高碳钢的热变形行为与再结晶组织研究[J]. 机械工程学报, 2020, 56(12): 116-123.
[6]	马明星, 王志新, 周家臣, 梁存, 朱达川, 张德良. Ti掺杂对CoCrCuFeMn高熵合金组织结构和耐磨性的影响[J]. 机械工程学报, 2020, 56(10): 110-116.
[7]	梁宾, 赵岩, 赵清江, 范体强, 李阳. 基于Gissmo失效模型的6016铝合金板材断裂行为研究及应用[J]. 机械工程学报, 2019, 55(18): 53-62.
[8]	王凯, 徐明林, 解鹏, 徐振, 陶淑苹. 空间高光谱相机调焦机构精度分析与试验[J]. 机械工程学报, 2019, 55(12): 29-36.
[9]	郑沛琪,王久和,陈启丽,马亮. 基于MOPSO的电力变换器多目标优化[J]. 电气工程学报, 2018, 13(12): 7-13.
[10]	陈飞, 刘建生, 马越. 关于轴类锻件拔长过程中组织均匀性控制的研究[J]. 机械工程学报, 2018, 54(10): 110-116.
[11]	周佳楠, 张国栋, 郑飞, 杨辉, 梅青松. Cr13不锈钢CMT堆焊金属表面高压滚压层结构与性能研究[J]. 机械工程学报, 2017, 53(8): 68-74.
[12]	石岩, 李云峰, 刘佳, 袁振玉. 高压油泵凸轮轴激光增材制造梯度耐磨层研究^*[J]. 机械工程学报, 2017, 53(6): 80-87.
[13]	陈尧, 宋磊, 张宸恺, 叶雪梅, 胡静. 38CrMoAl液压柱塞无白亮层低温离子渗氮工艺研究[J]. 机械工程学报, 2017, 53(22): 81-86.
[14]	卓秀秀, 徐桂芳, 袁圆, 罗锐, 程晓农. 0Cr17Mn17Mo3NiN奥氏体不锈钢的热变形行为及热加工图[J]. 机械工程学报, 2017, 53(22): 74-80.
[15]	秦芳诚, 齐会萍, 李永堂, 尉潇健. 42CrMo钢轴承环件铸辗成形及淬回火组织性能研究^*[J]. 机械工程学报, 2017, 53(2): 26-33.