汽轮机调节阀和调节级特性建模与配汽优化

doi:10.3901/JME.2019.18.165

机械工程学报 ›› 2019, Vol. 55 ›› Issue (18): 165-172.doi: 10.3901/JME.2019.18.165

• 可再生能源与工程热物理 • 上一篇

汽轮机调节阀和调节级特性建模与配汽优化

张浩峰¹, 胥建群¹, 孙友源², 黄喜军¹, 陈晓欣¹, 皇甫泽玉¹, 周丽丽¹

1. 东南大学能源热转换及其过程测控教育部重点实验室南京 210096;
2. 华电电力科学研究院有限公司杭州 310030

收稿日期:2019-01-27 修回日期:2019-06-15 发布日期:2020-01-07
通讯作者: 胥建群(通信作者),男,1959年出生,博士,教授。主要研究方向为汽轮机运行特性与理论建模、热力透平数值模拟等。E-mail:qlj1062@163.com
作者简介:张浩峰,男,1992年出生。主要研究方向为火电机组性能分析与优化。E-mail:245565723@qq.com

Characteristic Model of Combined Governing Valve and Governing Stage and Optimization of Steam Distribution of Steam Turbine

ZHANG Haofeng¹, XU Jianqun¹, SUN Youyuan², HUANG Xijun¹, CHEN Xiaoxin¹, HUANGFU Zeyu¹, ZHOU Lili¹

1. Key Laboratory of Energy Thermal Conversion and Control of Ministry of Education, Southeast University, Nanjing 210096;
2. Huadian EIectric Power Research Institute, Hangzhou 310030

Received:2019-01-27 Revised:2019-06-15 Published:2020-01-07

摘要/Abstract

摘要： 针对喷嘴配汽汽轮机，对调节阀和调节级联合进行建模，通过计算得到调节阀和调节级组合特性曲线，建立理论计算模型。该模型便于工程应用，利用调节阀和调节级组合的压比与阀门开度可计算得到准确的调节阀流量。基于计算模型，以某300 MW机组为研究对象，实现调节阀配汽函数的优化，并得到机组顺序阀流量特性；联合负荷和阀位，对其配汽方式进行优化。结果表明，经过验证调节阀和调节级的组合特性模型能够准确地反映现场调节阀特性。根据该模型实现流量特性的优化，得到合理的重叠度，提高阀门可控性；经过优化分析得到机组的最优滑压曲线，采用优化后的配汽方式运行，降低机组低负荷运行时的热耗，提高机组的灵活性和调峰能力。该优化方法对现场试验寻优提供理论基础。

关键词: 变工况, 调节阀, 调节级, 组合流量特性, 配汽优化

Abstract: For the nozzle steam turbine, the combined flow characteristics calculation model of governing valve and governing stage is established by calculation, and tested with open literature experimental data. The accurate flow of the governing valve can be calculated with the model by using the combination pressure ratio and the valve opening, which is convenient for engineering application. Method a calculation model for the off-design performance of a 300 MW steam turbine unit based on the combined valve model, and the valve distribution function is optimized, and the flow character of the sequential valve is obtained. Then the steam distribution optimization is analyzed by using the load and valve position. Analysis shows that the combined flow characteristics calculation model of governing valve and governing stage can reflect the characteristics of the valve accurately. According to the model, the flow characteristic is optimized, the reasonable overlap degree is obtained. The optimal slip pressure curve of the unit is obtained, which reduce the heat consumption during low-load operation of the unit and improves the flexibility and peak-regulating capacity of the unit and provides the theoretical basis for optimization test.

Key words: varying condition, governing valve, governing stage, the combination flow characteristics, optimization of steam distribution

中图分类号:

TK261

张浩峰, 胥建群, 孙友源, 黄喜军, 陈晓欣, 皇甫泽玉, 周丽丽. 汽轮机调节阀和调节级特性建模与配汽优化[J]. 机械工程学报, 2019, 55(18): 165-172.

ZHANG Haofeng, XU Jianqun, SUN Youyuan, HUANG Xijun, CHEN Xiaoxin, HUANGFU Zeyu, ZHOU Lili. Characteristic Model of Combined Governing Valve and Governing Stage and Optimization of Steam Distribution of Steam Turbine[J]. Journal of Mechanical Engineering, 2019, 55(18): 165-172.

参考文献

[1] 中国电力企业联合会. 2017-2018年度全国电力供需形势分析预测报告[R/OL].[2017-02-01]. http://www.cec.org.cn/guihuayutongji/gongzuodongtai/2018-02-2018/177584.html. China Electric Power Enterprise Federation. The analysis and forecast report of 2017-2018 national power supply and demand situation[R/OL].[2017-02-01]. http://www.cec.org.cn/guihuayutongji/Gongzuodongtai/2018-02-2018/177584.html.
[2] 国家发展改革委员会,国家能源局. 能源发展"十三五"规划[R]. 北京:人民出版社,2016. The National Development and Reform Commission and The National Energy Administration. The 13th five-year plan for energy development of the people's republic of china[R]. Beijing:Chinese People's Publishing House, 2016.
[3] KUBIK M L,COKER P J,BARLOW J F. Increasing thermal plant flexibility in a high renewables power system[J]. Applied Energy,2015,154:102-111.
[4] YONG H Y,KUNE Y S. Engineering analysis of mass flow rate for turbine system control and design[J]. Nuclear Engineering and Design,2011,241:4061-4078.
[5] HALIMI B,KIM S H,KUNE Y S. Engineering of combined valve flow for power conversion system[J]. Energy Conversion and Management,2013,65:448-455.
[6] GIORGIO Z. Experimental and numerical investigation into the aerodynamics of a novel steam turbine valve and its field application[J]. Journal of Engineering for Gas Turbines and Power. 2014,136:1-11.
[7] ANDREW G,FRAWLEY P. Experimental parametric equation for the prediction of valve coefficient (Cv) for choke valve trims[J]. International Journal of Pressure Vessels and Piping,2011,88(2-3):109-118.
[8] 张宝,樊印龙,顾正皓,等. 大型汽轮机流量特性试验[J]. 发电设备,2012,26(2):73-76. ZHANG Bao,FAN Yinlong,GU Zhenghao, et al. Flow characteristic test for large steam turbines[J]. Power Equipment,2012,26(2):73-76.
[9] PETER B,PHILIPP V,BALKOWSKI I,et al. A new emergency stop and control valves design:Part 1-experimental verification with scaled models[C]//ASME Turbo Expo 2014:Turbine Technical Conference and Exposition. 2014:V01BT27A001.
[10] LIESE E. Modeling of a steam turbine including partial arc admission for use in a process simulation software environment[C]//ASME 2011 International Mechanical Engineering Congress and Exposition. 2014:429-437.
[11] YANG Xinshe,HOSSEINI S,GANDOMI A H. Firefly algorithm for solving non-convex economic dispatch problems with valve loading effect[J]. Applied Soft Computing Journal,2012,12(3):1180-1186.
[12] YIN Changjie,LIU Jizhen. Study on valve management of DEH for steam turbine[J]. Energy & Power Engineering,2013,5(4):319-323.
[13] 马琳,胥建群,曹祖庆. 基于量纲分析的汽轮机调节级变工况特性研究[J]. 中国电机工程学报,2014,34(5):778-783. MA Lin,XU Jianqun,CAO Zuqing.Research on varying condition characteristic of steam turbine governing stage based on dimensional analysis[J].Proceedings of the Chinese Society for Electrical Engineering,2014,34(5):778-783.
[14] 雷志伟,张兴,陈涛,等. 基于模型自适应汽轮机调节门流量特性优化研究及应用[J]. 中国电力,2018,51(3):21-28. LEI Zhiwei,ZHANG Xing,CHEN Tao,et al. Research of steam turbine governing valve flow characteristic optimization based on adaptive model[J]. Electric Power,2018,51(3):21-28.
[15] 李玲,胥建群,石永锋. 600 MW汽轮机组运行方式优化研究[J]. 发电设备,2010,24(6):396-400. LI Ling,XU Jianqun,SHI Yongfeng. Operation mode optimization for a 600 MW steam turbine unit[J]. Power Equipment,2010,24(6):396-400.
[16] 曹祖庆. 汽轮机变工况特性[M]. 北京:水利水电出版社,1991. CAO Zuqing. Varying condition characteristic of steam turbine[M]. Beijing:Water Resources and Electric Power Press,1991.
[17] 胥建群,曹祖庆. 汽轮机调速系统和调节级数学模型[J]. 汽轮机技术,1991,31(1):15-21. XU Jianqun,CAO Zuqing.Turbine speed governor system and the mathematical model of governing stage[J]. Turbine Technology,1991,(1):15-21.
[18] MA Lin, XU Jianqun, et al. The influence of overlap degree research on nozzle governing characteristic[J]. Energy and Power Engineering,2013,5:642-645.
[19] 马琳,胥建群. 600MW汽轮机喷嘴配汽方式下阀门重叠度影响的研究[J]. 发电设备,2013,27(6):382-385. MA Lin,XU Jianqun. Study on influence of valve overlapping degree of 600 MW nozzle governing steam turbines[J]. Power Equipment,2013,27(6):382-385.
[20] XU Jianqun,MA Lin,SUN Youyuan,et al. Research on characteristics of varying conditions for nozzle governing stage based on dimensional analysis[J]. Energy,2014,65:590-595.
[21] PUSKA E. APROS couplings from core to containment[R]. Finland:VTT Technical Research Centre,2005.
[22] HANNINEN M. Phenomenological extensions to APROS six-equation model[R]. Finland:VTT Technical Research Centre,2009.
[23] LAAKSO P. Methods of simulation assisted automation testing[R]. Finland:VTT Technical Research Centre, 2005.

汽轮机调节阀和调节级特性建模与配汽优化

Characteristic Model of Combined Governing Valve and Governing Stage and Optimization of Steam Distribution of Steam Turbine

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 3

编辑推荐

Metrics

本文评价

[1]	王婷, 谷波, 钱程, 马洪涛. 车用小通道平行流换热器传热流动试验与分析[J]. 机械工程学报, 2016, 52(4): 141-147.
[2]	马育林;吴青;张蕊;叶蕾;严新平. 模拟自治车队行驶过程变工况速度跟踪控制[J]. , 2011, 47(7): 140-147.
[3]	王会义;于良耀;宋健. 汽车主动安全控制液压执行器的性能与原理[J]. , 2007, 43(9): 21-27.