反旋流对密封静力与动力特性影响的理论与试验研究

doi:10.3901/JME.2016.03.101

机械工程学报 ›› 2016, Vol. 52 ›› Issue (3): 101-109.doi: 10.3901/JME.2016.03.101

反旋流对密封静力与动力特性影响的理论与试验研究

孙丹¹, 王双¹, 艾延廷¹, 王克明¹, 肖忠会², 李云², 于小丹²

1. 沈阳航空航天大学辽宁省航空推进系统先进测试技术重点实验室沈阳 110136；
2. 沈阳鼓风机集团股份有限公司沈阳 110142

收稿日期:2015-02-09 修回日期:2015-10-20 出版日期:2016-02-05 发布日期:2016-02-05
通讯作者: 孙丹，男，1981年出生，博士，副教授。主要研究方向为旋转机械密封与滑动轴承流体激振理论与试验研究。 E-mail：phd_sundan@163.com
基金资助:
国家自然科学基金(11302133)、航空科学基金(20140454003)和辽宁省自然科学基金(2015020113)资助项目

Theoretical and Experimental Research on the Performance of Anti-swirl Flow for the Static and Dynamic Characteristics of Seals

SUN Dan¹, WANG Shuang¹, AI Yanting¹, WANG Keming¹, XIAO Zhonghui², LI Yun², YU Xiaodan²

1. Liaoning Key Lab of Advanced Test Technology for Aerospace Propulsion System, Shenyang Aerospace University, Shenyang 110136;
2. Shenyang Blower Works Group Co. Ltd., Shenyang 110142

Received:2015-02-09 Revised:2015-10-20 Online:2016-02-05 Published:2016-02-05

摘要/Abstract

摘要： 设计加工无/有反旋流共4种密封结构，从理论与实验两个方面研究反旋流对密封静力与动力特性的影响规律。建立反旋流密封静力特性CFD模型，理论分析反旋流对密封间隙流体切向速度、周向压力分布以及泄漏特性的影响；设计搭建反旋流密封动力特性试验台，试验测试无/有反旋流密封的泄漏特性，应用不平衡同频激励法试验研究反旋流对密封动力特性的影响。研究结果表明：反旋流可减小密封间隙流体的切向速度，进而降低密封间隙流体的周向压力差，且密封间隙流体周向压差随切向速度的减小而降低，这是反旋流抑制密封气流激振力的主要原因；密封的泄漏量随进出口压比的增加而增大，两者近似呈线性关系；与无反旋流密封相比，反旋流密封增加了密封的泄漏量，且随着进出口压比的增加，两者泄漏量差异增大；密封的动力特性系数的随密封进出口压比与转速的增加而增大。在相同工况下，主刚度大于交叉刚度约一个数量级，主阻尼与交叉阻尼数量级相同，且主阻尼大于交叉阻尼；反旋流可有效降低密封的等效刚度，增加密封的等效阻尼，提高密封的稳定性。

关键词: 动力特性, 反旋流, 静力特性, 密封, 振动

Abstract: Four kinds of seals with and without anti-swirl flow are designed and processed. Theoretical and experimental research on the performances of anti-swirl flow for the static and dynamic characteristics of seals is investigated. The anti-swirl flow seal static characteristics CFD theoretical model is set up to analyze the performance of anti-swirl flow on the tangential velocity, leakage and pressure distribution. Experiments are presented to test the leakage and the rotordynamic coefficients for the seals with and without anti-swirl flow. The rotordynamic coefficients are identified using an improved impedance method based on unbalanced synchronous excitation method. The results show that, compared to the traditional seals, the seals with anti-swirl flow have lower fluid tangential velocity, smaller circumferential pressure difference, and the fluid circumferential pressure difference decreases with the decreasing of the circumferential pressure difference. It is the main reason for anti-swirl flow reduces flow-induced force. Seal leakage increases almost linearly with inlet/outlet pressure ratio. The anti-swirl flow increases seal leakage, the leakage difference between with and without anti-swirl flow seal increases with the increase of inlet/outlet pressure ratio. Seal rotordynamic characteristic coefficients increase with inlet/outlet pressure ratio and rotational speed. In the same operating conditions, compare the cross-couple stiffness, direct stiffness has an order of magnitude higher. Cross-couple damper and direct damper have the same order of magnitudes, direct damper is bigger than cross-couple damper. The anti-swirl flow can effectively reduce the effective stiffness and increase the effective damping for variable conditions.

Key words: anti-swirl flow, dynamic characteristic, seal, static characteristic, vibration

中图分类号:

TK263

孙丹, 王双, 艾延廷, 王克明, 肖忠会, 李云, 于小丹. 反旋流对密封静力与动力特性影响的理论与试验研究[J]. 机械工程学报, 2016, 52(3): 101-109.

SUN Dan, WANG Shuang, AI Yanting, WANG Keming, XIAO Zhonghui, LI Yun, YU Xiaodan. Theoretical and Experimental Research on the Performance of Anti-swirl Flow for the Static and Dynamic Characteristics of Seals[J]. Journal of Mechanical Engineering, 2016, 52(3): 101-109.

参考文献

[1] 郎骥，杨建刚，曹浩. 可倾/固定密封内流体激振力计算与试验比较[J]. 机械工程学报，2013，49(3)：101-105. LANG Ji，YANG Jiangang，CAO Hao. Calculation and experimental comparision of fluid induced force between the titling pad seal and fixed pad seal[J]. Journal of Mechanical Engineering，2013，49(3)：101-105.
[2] 曹浩，杨建刚，郭瑞，等. 密封动力特性系数试验识别方法及影响因素分析[J]. 机械工程学报，2011，47(9)：85-89. CAO Hao，YANG Jiangang，GUO Rui，et al. Experimental identification method and influence factor analysis of seal dynamic characteristic[J]. Journal of Mechanical Engineering，2011，47(9)：85-89.
[3] 曹树谦，陈予恕. 现代密封转子动力学研究综述[J]. 工程力学，2009，26(增Ⅱ)：68-79. CAO Shuqian，CHEN Yushu. A review of modern rotor/seal dynamics[J]. Engineering Mechanics，2009，26(Suppl.Ⅱ)：68-79.
[4] SUN Dan，YANG Jiangang，GUO Rui，et al. A trigonometric series expansion based method for the research of static and dynamic characteristics of eccentric seals[J]. Journal of Mechanical Science and Technology，2014，28(6)：2111-2120.
[5] 李军，李志刚. 袋型阻尼密封泄漏流动和转子动力特性的研究进展[J]. 力学进展，2011，41(5)：379-395. LI Jun，LI Zhigang. Review of the leakage flow and rotordynamic characteristics of pocket damper seals[J]. Advances in Mechanics，2011，41(5)：379-395.
[6] 何立东，高金吉. 三维转子密封系统气流激振的研究[J]. 机械工程学报，2003，39(3)：100-104. HE Liding，GAO Jinji. Study on gas flow-induced vibration for a three-dimensional rotor-seal system[J]. Chinese Journal of Mechanical Engineering，2003，39(3)：100-104.
[7] KIRK G，GAO R. Influence of preswirl on rotordynamic characteristics of labyrinth seals[J]. Tribology Transactions，2012，55(3)：357-364.
[8] MUSZYNSKA A，BENTLY D E. Anti-swirl arrangements prevent rotor/seal instability[J]. Journal of Vibration and Acoustics，1989，111(2)：156-162.
[9] TOSHIYA K，SATOSHI K，MITSURU S，et al. Effects of swirl brakes on the leakage flow between the casing and the shroud of a centrifugal impeller[C]// Proceedings of the ASME-JSME-KSME 2011 Joint Fluids Engineering Conference AJK-Fluid，2011.
[10] RICCARDO D S，MIRKO M，ANTONIC A，et al. Numerical characterization of swirl brakes for high pressure centrifugal compressors[C]// Proceedings of ASME Turbo Expo 2013：Turbine Technical Conference and Exposition GT2013，2013.
[11] NIELSEN K K，CHILDS D W，MYLLERUP C W. Experimental and theoretical comparison of two swirl brake designs[J]. Journal of Turbomachinery，2001，123(2)：353-358.
[12] LI Jiming，PRANABESH D C ，FRANK K . Evaluation of centrifugal compressor stability margin and investigation of antiswirl mechanism[C]// Proceedings of the Thirty-Second Turbomachinery Symposium，2003：49-57.
[13] MEMMOTT E A. Stability analysis and testing of a train of centrifugal compressors for high pressure gas injection[J]. Journal of Engineering for Gas Turbines and Power，1999，121(3)：509-514.
[14] KIM N，PARK S Y，RHODE D. Predicted effects of shunt injection on the rotordynamics of gas labyrinth seals[J]. Journal of Engineering for Gas Turbines and Power，2002，125 (1)：167-174.
[15] SOTO E A，CHILDS D W. Experimental rotordynamic coefficient results for (a) a labyrinth seal with and without shunt injection and (b) a honeycomb seal[J]. Journal of Engineering for Gas Turbines and Power，1999，121(1)：153-159.
[16] 沈庆根，李烈荣，潘永密. 迷宫密封中的气流激振及其反旋流措施[J]. 流体机械，1994，22(7)：7-11. SHEN Qinggen，LI Lierong，PAN Yongmi. Flow-induced force and anti-preswirl mechanism for labyrinth seals[J]. Fluid Machinery，1994，22(7)：7-11.
[17] 何立东. 转子密封系统反旋流抑振的数值模拟[J]. 航空动力学报，1999，14(3)：293-333. HE Lidong. Numerical simulation of anti-swirl arrangements for suppressing rotor/seal instability[J]. Journal of Aerospace Power，1999，14(3)：293-333.
[18] 吕成龙，何立东，涂霆. 反旋流抑制密封间隙内流体激振研究[J]. 液压气动与密封，2014，(10)：28-31，77. Lü Chenglong，HE Lidong，TU Ting. Study on suppressing fluid-induced vibration in the seal clearance by anti-swirl flow[J]. Hydraulics Pneumatics & Seals，2014，(10)：28-31，77.
[19] PHILIP D B. Measurement versus predictions of rotordynamic coefficients and leakage rates for a hole-pattern gas seal with negative preswirl[D]. Master Thesis Texas A&M University，2011.
[20] LI Zhigang，LI Jun，FENG Zhenping. Numerical investigations on the leakage and rotordynamic characteristics of pocket damper seals part I：Effects of pressure ratio rotational speed，and inlet preswirl[J]. Journal of Engineering for Gas Turbines and Power，2015，137：032503，1-15.

反旋流对密封静力与动力特性影响的理论与试验研究

Theoretical and Experimental Research on the Performance of Anti-swirl Flow for the Static and Dynamic Characteristics of Seals

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	宫燃, 程志高, 徐宜, 张玉东, 张鹤. 旋转密封两种热失稳现象的表征建模与特性研究[J]. 机械工程学报, 2019, 55(9): 55-62.
[2]	张骞, 孟宪洪, 凌烈鹏, 高芒芒, 于梦阁. 重载铁路大跨度钢桁梁桥复合材料轨枕适应性[J]. 机械工程学报, 2019, 55(8): 145-153.
[3]	倪陈兵, 朱立达, 宁晋生, 杨志超, 刘长福. 超声振动辅助铣削钛合金铣削力信号及切屑特征研究[J]. 机械工程学报, 2019, 55(7): 207-216.
[4]	王建磊, 张琛, 王晓虎, 王栋平, 李建克, 贾谦, 陈润霖, 崔亚辉. N₂O₄环境下液体火箭发动机涡轮泵机械密封浸渍石墨的磨损机理研究[J]. 机械工程学报, 2019, 55(7): 119-127.
[5]	杨光, 胡志超, 张军, 皮钧, 刘中生. 超声振动改善电铸表面粗糙度的机理[J]. 机械工程学报, 2019, 55(7): 243-248.
[6]	高泽, 张德远, 李哲, 姜兴刚, 刘佳佳. 高速超声椭圆振动铣削腹板表面质量研究[J]. 机械工程学报, 2019, 55(7): 249-256.
[7]	蒋建东, 章恩光, 赵颖娣, 李聪聪, 乔欣. 盾构刀盘振动掘削动力学建模与仿真研究[J]. 机械工程学报, 2019, 55(5): 113-120.
[8]	白有盾, 陈新, 杨志军. 考虑阻尼衰减的点位操作时间最优运动规划[J]. 机械工程学报, 2019, 55(5): 104-112.
[9]	孙明翰, 杨玉青, 朱志旺, 魏洁平, 杜凤山. 20CrMn钢双辊薄带振动铸轧细晶机理试验[J]. 机械工程学报, 2019, 55(4): 54-59.
[10]	汪久根, 柯梁亮. 基于残差网络的RV减速器故障诊断[J]. 机械工程学报, 2019, 55(3): 73-80.
[11]	柏朗, 李言, 杨明顺, 姚梓萌, 姚志远. 超声振动-单点增量复合成形过程中成形力的分析与建模[J]. 机械工程学报, 2019, 55(2): 42-50.
[12]	李瑞君, 常振鑫, 雷英俊, 胡鹏浩, 范光照. 基于DVD光学读取头的悬臂式低频加速度计[J]. 机械工程学报, 2019, 55(2): 10-17.
[13]	余磊, 刘莉, 马志赛, 康杰. 基于多维振动响应GSC-TARMA模型的时变结构模态参数辨识[J]. 机械工程学报, 2019, 55(15): 183-192.
[14]	肖鑫, 汤宝平, 邓蕾, 黄艺. 机械振动无线传感器网络跨层同步采集累积误差控制方法[J]. 机械工程学报, 2019, 55(15): 202-207.
[15]	钟剑锋, 钟舜聪, 彭志科. 位感条纹三维振动测量原理及试验研究[J]. 机械工程学报, 2019, 55(14): 19-29.