宽域加工误差对拓扑修形齿轮传动误差的影响

doi:10.3901/JME.2023.15.131

机械工程学报 ›› 2023, Vol. 59 ›› Issue (15): 131-141.doi: 10.3901/JME.2023.15.131

扫码分享

宽域加工误差对拓扑修形齿轮传动误差的影响

刘欣荣¹, 王慧鹏¹, 汪中厚², 杨勇明²

1. 上海工程技术大学机械与汽车工程学院上海 201620;
2. 上海理工大学机械工程学院上海 200093

收稿日期:2022-08-05 修回日期:2022-11-15 出版日期:2023-08-05 发布日期:2023-09-27
通讯作者: 汪中厚(通信作者),男,1963年出生,博士,教授,博士研究生导师。主要研究方向为机械传动技术、CAE技术及应用。E-mail:wangzhusst@163.com
作者简介:刘欣荣,男,1987年出生,博士,讲师,硕士研究生导师。主要研究方向为齿轮系统动力学。E-mail:01190007@sues.edu.cn
基金资助:
国家自然科学基金资助项目(51875360)

Influence of Wide-swath Machining Error on Transmission Error of Topological Modification Gear Transmission System

LIU Xinrong¹, WANG Huipeng¹, WANG Zhonghou², YANG Yongming²

1. School of Mechanical and Automotive Engineering, Shanghai University of Engineering Science, Shanghai 201620;
2. School of Mechanical Engineering, University of Shanghai for Science and Technology, Shanghai 200093

Received:2022-08-05 Revised:2022-11-15 Online:2023-08-05 Published:2023-09-27

摘要/Abstract

摘要： 拓扑修形作为高性能齿轮修形的重要方式,为提高齿轮系统动态性能提供了有效方法。建立齿轮系统的弯-扭-轴-摆动力学模型,基于诱导法曲率分析拓扑修形齿轮中凹齿廓误差形成机理,研究宽域加工误差对齿轮系统传动误差的影响。通过数值计算得出齿形齿向修形量误差、齿向倾斜误差、中凹齿廓误差、欠磨削及过磨削误差作用下的齿轮系统传动误差,建立量纲归一的无因次齿轮系统动传动误差评价方法,采用F分布检验回归方程的显著性,阐明拓扑修形齿轮宽域加工误差与齿轮系统传动误差的内在联系。结果表明,在宽域加工误差作用下,ζ₁、ζ₂、ζ₃、ζ₄、ζ₄的无因次标准回归系数分别为0.128,0.452,0.222,1.146,0.784,在误差量相同情况下,中凹齿廓误差对齿轮传动误差影响最显著。研究成果将为拓扑修形齿轮的加工误差分配提供理论支撑。

关键词: 拓扑修形, 宽域加工误差, 传动误差, 量纲归一

Abstract: As an important way of high-performance gear modification, topological modification provides an effective method to improve the dynamic performance of transmission system. Based on the induced normal curvature, the formation mechanism of concave tooth profile error in topological modified gear is analysed, a bend-twist-axis-swing dynamics model of the gear system is established and the influence of wide-swath machining error on the transmission error of transmission system is studied. Through numerical calculation, the transmission error of transmission system under tooth profile modification error, tooth inclination error, tooth profile concave error, under-grinding and over-grinding machining errors are obtained. The evaluation method of dynamic transmission error of dimensionless gear system is established, the significance of regression equation is tested by F distribution, and the internal relationship between wide range machining error of topological modified gear and transmission error of gear system is clarified. The results show that, with the influence of wide-swath machining error, the dimensionless standard regression coefficients of ζ₁,ζ₂,ζ₃,ζ₄,ζ₅ and are 0.128, 0.452, 0.222, 1.146 and 0.784 respectively. Under the same amount, the concave tooth profile error has the most significant effect on the gear transmission error. The research results will provide a theoretical basis for the distribution of machining errors in gear topology modification and lay the foundation for obtaining high performance gears.

Key words: topology modification, wide-swath machining error, transmission error, dimensional normalization

中图分类号:

TH132

刘欣荣, 王慧鹏, 汪中厚, 杨勇明. 宽域加工误差对拓扑修形齿轮传动误差的影响[J]. 机械工程学报, 2023, 59(15): 131-141.

LIU Xinrong, WANG Huipeng, WANG Zhonghou, YANG Yongming. Influence of Wide-swath Machining Error on Transmission Error of Topological Modification Gear Transmission System[J]. Journal of Mechanical Engineering, 2023, 59(15): 131-141.

参考文献

[1] 陈思雨,唐进元,王志伟,等. 修形对齿轮系统动力学特性的影响规律[J]. 机械工程学报,2014,50(13):59-65. CHEN Siyu,TANG Jinyuan,WANG Zhiwei,et al. Effect of modification on dynamic characteristics of gear transmissions system[J]. Journal of Mechanical Engineering,2014,50(13):59-65.
[2] 王桂华,井海龙,史妍妍,等. 基于响应面法的齿轮容差设计方法研究[J]. 航空发动机,2016,42(3):1-6. WANG Guihua,JING Hailong,SHI Yanyan,et al. Methods of tolerance design for gears based on response surface methodology[J]. Aeroengine,2016,42(3):1-6.
[3] 刘铁军,孙宝玉,张西龙. 基于磨削齿轮方式修整齿轮误差的分析[J]. 机电工程,2012,29(5):506-511. LIU Tiejun,SUN Baoyu,ZHANG Xilong. Analysis of modifying gear error based on grinding gear method[J]. Journal of Mechanical and Electrical Engineering,2012,29(5):506-511.
[4] 蒋进科,方宗德,刘钊. 拓扑修形斜齿轮齿面插齿修正[J]. 华中科技大学学报,2019,47(7):102-107. JIANG Jinke,FANG Zongde,LIU Zhao. Modification of tooth surface shaping of topological modified helical gears[J]. Journal of Huazhong University of Science and Technology,2019,47(7):102-107.
[5] 汪中厚,刘绍鲲,刘欣荣,等. 拓扑修形齿轮齿面误差分析[J]. 机械传动,2017,41(11):50-53. WANG Zhonghou,LIU Shaokun,LIU Xinrong,et al. Analysis of tooth surface error of topology modification gear[J]. Journal of Mechanical Transmission,2017,41(11):50-53.
[6] 吴阳,侯力,罗岚,等. 机床误差对圆弧齿线圆柱齿轮齿面误差影响规律的理论研究[J]. 机械工程学报,2020,56(21):100-109. WU Yang,HOU Li,LUO Lan,et al. Research on the effect law of machine tool errors on tooth surface errors of curvilinear gear[J]. Journal of Mechanical Engineering,2020,56(21):100-109.
[7] JIANG J K,FANG Z D. High-order tooth flank correction for a helical gear on a six-axis CNC hob machine[J]. Mechanism and Machine Theory,2015,91:227-237.
[8] TRAN V Q,WU Y R. A novel method for closed-loop topology modification of helical gears using internal-meshing gear honing[J]. Mechanism and Machine Theory,2020,145:1-15.
[9] 邓效忠,徐爱军,张静,等. 基于时标域频谱的齿轮传动误差分析与试验研究[J]. 机械工程学报,2014,50(1):85-90. DENG Xiaozhong,XU Aijun,ZHANG Jing,et al. Analysis and experimental research on the gear transmission error based on pulse time spectrum[J]. Journal of Mechanical Engineering,2014,50(1):85-90.
[10] 蔡安江,刘立博,刘磊,等. 切削参数对剃齿切削力及齿形中凹误差的影响[J]. 中国机械工程,2020,31(6):655-661. CAI Anjiang,LIU Libo,LIU Lei,et al. Influences of cutting parameters on shaving cutting forces and tooth profile concave errors[J]. China Mechanical Engineering,2020,31(6):655-661.
[11] 吴序堂. 齿轮啮合原理[M]. 西安:西安交通大学出版社,2009. WU Xutang. Meshing theory of gear[M]. Xi'an:Xi'an Jiaotong University Press,1986.
[12] 王会良,邓效忠,杨建军,等. 分段拓扑修形齿轮的成形磨削与试验[J]. 航空动力学报,2014,29(12):3000-3008. WANG Huiliang,DENG Xiaozhong,YANG Jianjun,et al. Form grinding and experiment on segment topographic modification gear[J]. Journal of Aerospace Power,2014,29(12):3000-3008.
[13] 李国龙,李先广,刘飞,等. 拓扑修形齿轮附加径向运动成形磨削中的砂轮廓形优化方法[J]. 机械工程学报,2011,47(11):155-162. LI Guolong,LI Xianguang,LIU Fei,et al. Method of profile optimization of a form grinding wheel for grinding with additional radial motion of topologically modified gear[J]. Journal of Mechanical Engineering,2011,47(11):155-162.
[14] 邹玉静,庞峰,樊智敏. 渐开线斜齿轮传动摩擦动力学耦合研究[J]. 机械工程学报,2019,55(3):109-119. ZOU Yujing,PANG Feng,FAN Zhimin. Coupling research on dynamical behavior and elastohydrodynamic lubrication property of helical gear[J]. Journal of Mechanical Engineering,2019,55(3):109-119.
[15] 范孝良,石鹏飞,刘建民. 风电齿轮箱微观修形对振动与声振粗糙度性能的影响[J]. 中国工程机械学报,2019,17(1):43-48. FAN Xiaoliang,SHI Pengfei,LIU Jianmin. Influence of micro modification on noise,vibration,harshness performance of wind turbine gearbox[J]. Journal of Mechanical Transmission,2019,17(1):43-48.
[16] 袁冰,常山,刘更,等. 大齿宽齿轮耦合转子系统准静态接触分析及动态特性[J]. 机械工程学报,2020,56(3):96-105. YUAN Bing,CHANG Shan,LIU Geng,et al. Quasi-static contact and dynamic behaviors analysis of wide-faced gear coupled with rotor system[J]. Journal of Mechanical Engineering,2020,56(3):96-105.
[17] 唐进元,卢延峰,周超. 有误差的螺旋锥齿轮传动接触分析[J]. 机械工程学报,2008,44(7):16-23. TANG Jinyuan,LU Yanfeng,ZHOU Chao. Error tooth contact analysis of spiral bevel gears transmission[J]. Journal of Mechanical Engineering,2008,44(7):16-23.
[18] WANG Zhiwei,CHENG Yao,MEI Guiming,et al. Torsional vibration analysis of the gear transmission system of high-speed trains with wheel defects[J]. Proceedings of the Institution of Mechanical Engineers,2020,234(2):123-133.
[19] 汪中厚. 准双曲面齿轮动态性能仿真[M]. 北京:科学出版社,2016. WANG Zhonghou. Dynamic performance simulation of hypoid gear[M]. Beijing:Science Press,2016.

宽域加工误差对拓扑修形齿轮传动误差的影响

Influence of Wide-swath Machining Error on Transmission Error of Topological Modification Gear Transmission System

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 14

编辑推荐

Metrics

本文评价

[1]	杜彦斌, 汪澳婷, 何坤. 含扭曲误差的鼓形斜齿轮接触分析[J]. 机械工程学报, 2024, 60(3): 143-154.
[2]	苏进展, 李旭东, 尹逊民, 贾海涛, 郭芳. 人字齿轮直线型对角修形设计及成形磨原理[J]. 机械工程学报, 2023, 59(5): 121-129.
[3]	邹帅东, 王光建, 蒋宇将, 任品旭, 喻立, 李小兵. 交变负载下变齿厚齿轮副侧隙控制试验研究[J]. 机械工程学报, 2020, 56(15): 138-146.
[4]	蒋进科, 方宗德, 刘红梅. 行星传动多体齿轮承载接触特性分析[J]. 机械工程学报, 2019, 55(15): 174-182.
[5]	曹雪梅, 杨博会, 邓效忠. 轮齿接触分析的分解算法与试验验证[J]. 机械工程学报, 2018, 54(5): 47-52.
[6]	蔡安江, 张华, 李玲, 刘磊, 李丽霞. 非等边剃齿刀的齿形设计[J]. 机械工程学报, 2018, 54(19): 34-40.
[7]	江平, 刘光磊, 张瑞庭, 鲁锐. 航空弧齿锥齿轮接触印痕高度的一种控制方法[J]. 机械工程学报, 2015, 51(5): 64-70.
[8]	郭辉，赵宁，项云飞，张蒙祺. 六轴数控蜗杆砂轮磨齿机磨削面齿轮的方法[J]. 机械工程学报, 2015, 51(11): 186-194.
[9]	邓效忠;徐爱军;张静;李聚波;徐恺. 基于时标域频谱的齿轮传动误差分析与试验研究[J]. , 2014, 50(1): 85-90.
[10]	李国龙;李先广;刘飞;孙孟辉. 拓扑修形齿轮附加径向运动成形磨削中的砂轮廓形优化方法[J]. , 2011, 47(11): 155-162.
[11]	崔亚辉;刘占生;叶建槐. 齿轮—转子耦合系统的动态响应及齿侧间隙对振幅跳跃特性的影响[J]. , 2009, 45(7): 7-15.
[12]	曹雪梅;方宗德;许浩;朱自冰. 弧齿锥齿轮的齿面主动设计及试验验证[J]. , 2008, 44(7): 209-214.
[13]	曹雪梅;方宗德;张金良;邓效忠. 弧齿锥齿轮的齿面主动设计[J]. , 2007, 43(8): 155-158.
[14]	孙月海;张策;葛楠. 含误差的直齿轮的齿廓修形[J]. , 2003, 39(12): 91-94.