滚动轴承外圈多点故障特征分析

doi:10.3901/JME.2020.21.110

机械工程学报 ›› 2020, Vol. 56 ›› Issue (21): 110-120.doi: 10.3901/JME.2020.21.110

扫码分享

滚动轴承外圈多点故障特征分析

胡爱军, 许莎, 向玲, 张军华

华北电力大学机械工程系保定 071003

收稿日期:2019-11-08 修回日期:2020-03-24 出版日期:2020-11-05 发布日期:2020-12-19
作者简介:胡爱军,男,1971年出生,博士,教授。主要研究方向为机械设备状态监测与故障诊断。E-mail:bdlaohu@126.com
基金资助:
国家自然科学基金资助项目(51675178)。

Characteristic Analysis of Multi-point Faults on the Outer Race of Rolling Element Bearing

HU Aijun, XU Sha, XIANG Ling, ZHANG Junhua

Department of Mechanical Engineering, North China Electric Power University, Baoding 071003

Received:2019-11-08 Revised:2020-03-24 Online:2020-11-05 Published:2020-12-19

摘要/Abstract

摘要： 滚动轴承发生多点故障时会产生复杂的振动特征,影响轴承故障诊断的准确性。针对滚动轴承外圈多点故障诊断特征的变化规律,考虑滚动轴承外圈故障数量、故障间隔和载荷分布对故障特征的影响,采用五自由度动力学模型进行仿真分析。通过龙格库塔法对动力学方程进行数值求解,分析了滚动轴承外圈单点故障和多点故障的诊断特征。结果表明:当外圈具有多点故障时,随着故障数量和故障间隔的变化,故障特征频率各谐波的幅值会发生变化;当多点故障满足载荷相等和一定的间隔关系时,故障特征频率值与故障数量之间呈现对应的倍数关系。通过滚动轴承多点故障模拟试验验证了结论的正确性。

关键词: 滚动轴承, 外圈故障, 多点故障, 动力学模型, 故障特征

Abstract: Complex vibration characteristics produced by the multi-point faults of rolling bearing, may affect the accuracy of bearing fault diagnosis. Considering the influence of the number of faults, fault interval and load distribution, the multi-point faults of rolling element bearing is simulated and analyzed by using five degrees of freedom dynamic model. The dynamic equation is solved numerically by runge-kutta method, and the characteristics of single point fault and multi-point faults of the outer race are compared. The results show that when the outer race has multi-point faults, the amplitude of each harmonic of fault characteristic frequency will change as the change of fault number and fault interval. When the multi-point faults satisfy the relationship of load equality and a certain interval, the value of fault characteristic frequency is a multiple relationship between the fault frequency and the number of faults. The conclusion is verified by the multi-point faults simulation experiment of rolling element bearing.

Key words: rolling element bearing, outer race fault, multi-point faults, dynamic model, fault characteristics

中图分类号:

TG156

胡爱军, 许莎, 向玲, 张军华. 滚动轴承外圈多点故障特征分析[J]. 机械工程学报, 2020, 56(21): 110-120.

HU Aijun, XU Sha, XIANG Ling, ZHANG Junhua. Characteristic Analysis of Multi-point Faults on the Outer Race of Rolling Element Bearing[J]. Journal of Mechanical Engineering, 2020, 56(21): 110-120.

参考文献

[1] RAI A,UPADHYAY S H.A review on signal processing techniques utilized in the fault diagnosis of rolling element bearings[J].Tribology International,2016,96:289-306.
[2] RANDALL R B,ANTONI J.Rolling element bearing diagnostics-a tutorial[J].Mechanical Systems and Signal Processing,2011,25(2):485-520.
[3] HU A,XIANG L,XU S,et al.Frequency loss and recovery in rolling bearing fault detection[J].Chinese Journal of Mechanical Engineering,2019,32(1):35.
[4] 刘永强,王宝森,杨绍普.含外圈故障的高速列车轴承转子系统非线性动力学行为分析[J].机械工程学报,2018,54(8):17-25. LIU Yongqiang,WANG Baosen,YANG Shaopu.Nonlinear dynamic behaviors analysis of the bearing rotor system with outer ring faults in the high-speed train[J].Journal of Mechanical Engineering,2018,54(8):17-25.
[5] MCFADDEN P D,SMITH J D.Model for the vibration produced by a single point defect in a rolling element bearing[J]. Journal of Sound and Vibration,1984,96(1):69-82.
[6] MCFADDEN P D,SMITH J D.The vibration produced by multiple point defects in a rolling element bearing[J].Journal of Sound and Vibration,1985,98(2):263-273.
[7] IGARASHI T,KATO J.Studies on the vibration and sound of defective rolling bearings third report:vibration of ball bearing with multiple defects[J].JSME Bulletin 1985,28(237):492-499.
[8] PATEL V N,TANDON N,PANDEY R K.A dynamic model for vibration studies of deep groove ball bearings considering single and multiple defects in races[J].Journal of Tribology,2010,132(4):041101.
[9] PATEL V N,TANDON N,PANDEY R K.Vibrations generated by rolling element bearings having multiple local defects on races[J].Procedia Technology,2014,14:312-319.
[10] YAQUB M F,GONDAL I,KAMRUZZAMAN J,et al.Abrasion modeling of multiple-point defect dynamics for machine condition monitoring[J].IEEE Transactions on Reliability,2013,62(1):171-182.
[11] YANG R,JIN Y,HOU L,et al.Advantages of pulse force model over geometrical boundary model in a rigid rotor ball bearing system[J]. International Journal of Non-Linear Mechanics,2018,102:159-169.
[12] CAO H,NIU L,XI S,et al.Mechanical model development of rolling bearing-rotor systems:A review[J].Mechanical Systems and Signal Processing,2018,102:37-58.
[13] LIU J,SHAO Y.Overview of dynamic modelling and analysis of rolling element bearings with localized and distributed faults[J].Nonlinear Dynamics,2018,93:1765-1798.
[14] YANG R,JIN Y,HOU L,et al.Study for ball bearing outer race characteristic defect frequency based on nonlinear dynamics analysis[J].Nonlinear Dynamics,2017,90:781-796.
[15] 刘静,师志峰,邵毅敏.考虑局部故障边缘形态的球轴承振动特征[J].振动、测试与诊断,2017,37(4):807-813. LIU Jing,SHI Zhifeng,SHAO Yimin.An investigation of vibration characteristics of a ball bearing with a localized defect considering different edge shapes[J].Journal of Vibration,Measurement& Diagnosis,2017,37(4):807-813.
[16] 关贞珍,郑海起,王彦刚.滚动轴承局部损伤故障动力学建模及仿真[J].振动、测试与诊断,2012,32(6):950-955. GUAN Zhenzhen,ZHENG Haiqi,WANG Yangang.Fault dynamic modeling and simulating of rolling bearing with localized defect[J]. Journal of Vibration,Measurement& Diagnosis,2012,32(6):950-955.
[17] SOPANEN J,MIKKOLA A.Dynamic model of a deep groove ball bearing including localized and distributed defects,part 1:Theory[J].Proceedings of the Institution of Mechanical Engineers,Part K:Journal of Multi-body Dynamics,2003,217:201-211.
[18] SOPANEN J,MIKKOLA A.Dynamic model of a deep groove ball bearing including localized and distributed defects,part 2:Implementation and Results[J]. Proceedings of the Institution of Mechanical Engineers,Part K:Journal of Multi-body Dynamics,2003,217:213-223.
[19] LIEW A,FENG N S,HAHN E J.Transient rotordynamic modeling of rolling element bearing systems[J]. Journal of Engineering for Gas Turbines& Power,2002,124(4):V004T03A021.
[20] SWALHI N,RANDALL R B.Simulating gear and bearing interactions in the presence of faults:Part I.the combined gear bearing dynamic model and the simulation of localized bearing faults[J].Mechanical Systems& Signal Processing,2008,22(8):1924-1951.
[21] SWALHI N,RANDALL R B.Simulating gear and bearing interactions in the presence of faults:part II.simulation of the vibrations produced by extended bearing faults[J].Mechanical Systems& Signal Processing,2008,22(8):1952-1966.
[22] MISHRA C,SAMANTARAY A K,CHAKRABORTY G. Ball bearing defect models:A study of simulated and experimental fault signatures[J].Journal of Sound and Vibration,2017,400:86-112.
[23] HARRIS T A,KOTZALAS M N.滚动轴承分析:第一卷轴承技术的基本概念[M].北京:机械工业出版社,2010. HARRIS T A,KOTZALAS M N.Essential concepts of bearing technology[M]. Beijing:China Machine Press,2010.

滚动轴承外圈多点故障特征分析

Characteristic Analysis of Multi-point Faults on the Outer Race of Rolling Element Bearing

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张行, 富宽, 陈铭浩, 李睿, 石新娜. 压差式多节串联管道机器人越障时动力学演化规律及减振分析[J]. 机械工程学报, 2024, 60(8): 348-359.
[2]	高帅, 韩勤锴, 褚福磊. 具备实时动态稳定性监测特性的高速混合陶瓷摩擦电滚动轴承[J]. 机械工程学报, 2024, 60(15): 80-88.
[3]	曹杰, 任尊松, 查浩, 徐宁, 杨超. 高速动车组齿轮箱轴承载荷特性研究[J]. 机械工程学报, 2024, 60(15): 173-184.
[4]	黄包裕, 张永祥. 一种基于三步法的轴承故障诊断方法[J]. 机械工程学报, 2024, 60(14): 51-68.
[5]	邓智铭, 黄土地, 黄洪钟, 尉询楷, 王浩. 变工况条件下角接触球轴承疲劳剥落故障演化加速试验载荷谱研究[J]. 机械工程学报, 2024, 60(13): 193-204.
[6]	王振亚, 刘韬, 伍星. 互信息规范的卷积神经网络及其在轴承故障特征提取中的应用[J]. 机械工程学报, 2024, 60(12): 137-146.
[7]	邓磊鑫, 谢清林, 陶功权, 温泽峰. 基于轴箱振动与动力学模型驱动的高速列车车轮失圆状态识别方法[J]. 机械工程学报, 2023, 59(3): 110-121.
[8]	王宇, 刘秋发, 彭一真. 非均匀监测条件下滚动轴承剩余寿命预测方法[J]. 机械工程学报, 2023, 59(23): 96-104.
[9]	陈彪, 江浩斌, 栗欢欢, 赵钱, 王天鸶. 基于气液动力学热耦合模型的动力电池SOC估算[J]. 机械工程学报, 2023, 59(22): 163-175.
[10]	熊万里, 曾旭, 张翰乾, 李媛媛, 原帅, 金志鑫. 全液体静压支承结构磨削系统的磨削成圆规律及圆度极限预测[J]. 机械工程学报, 2023, 59(21): 85-98.
[11]	苗永浩, 石惠芳, 李晨辉, 王南飞. 谐波特征模式分解方法在轴承故障诊断中的应用[J]. 机械工程学报, 2023, 59(21): 234-244.
[12]	杨绍普, 顾晓辉, 刘永强, 邓飞跃, 刘泽潮, 刘文朋, 王宝森. 转向架关键运动部件动力学机理与故障诊断研究综述[J]. 机械工程学报, 2023, 59(20): 225-243.
[13]	丁孺琦, 王振, 程敏, 徐兵, 刘子辰. 基于模型控制的液压机械臂高精度轨迹跟踪[J]. 机械工程学报, 2023, 59(14): 298-309.
[14]	胡文扬, 王天杨, 张飞斌, 褚福磊. 仿真驱动下基于Ramanujan周期变换的轴承早期故障特征提取[J]. 机械工程学报, 2023, 59(13): 148-156.
[15]	李春明, 鲍珂. 基于载荷传递路径的履带车辆多层级耦合动力学建模与分析[J]. 机械工程学报, 2023, 59(13): 157-174.