反转泵液力透平速度滑移机理

doi:10.3901/JME.2018.24.189

机械工程学报 ›› 2018, Vol. 54 ›› Issue (24): 189-196.doi: 10.3901/JME.2018.24.189

扫码分享

反转泵液力透平速度滑移机理

王晓晖^1,2, 杨军虎^1,2, 郭艳磊¹, 夏正廷¹, 苗森春¹

1. 兰州理工大学能源与动力工程学院兰州 730050;
2. 甘肃省流体机械及系统重点实验室兰州 730050

收稿日期:2017-12-20 修回日期:2018-07-13 出版日期:2018-12-20 发布日期:2018-12-20
通讯作者: 杨军虎(通信作者),男,1962年出生,教授,博士研究生导师。主要研究方向为液力透平设计理论及内流机理。E-mail:lzyangjh@lut.cn
作者简介:王晓晖,男,1986年出生,博士研究生。主要研究方向为液力透平设计理论及内流机理。E-mail:wangxiaohui5718@163.com
基金资助:
国家自然科学基金（51569013）和甘肃省青年科技基金（145RJYA312）资助项目。

Research on Slip Phenomenon of Pumps as Turbines

WANG Xiaohui^1,2, YANG Junhu^1,2, GUO Yanlei¹, XIA Zhengting¹, MIAO Senchun¹

1. School of Energy and Power engineering, Lanzhou University of Technology, Lanzhou 730050;
2. Key Laboratory of Fluid Machinery and System, Lanzhou 730050

Received:2017-12-20 Revised:2018-07-13 Online:2018-12-20 Published:2018-12-20

摘要/Abstract

摘要： 速度滑移对液力透平的水力性能和内流特性有一定影响。以反转泵液力透平为研究对象，评估不同湍流模型对液力透平水力性能影响的敏感性，通过数值模拟与试验值误差分析发现，采用RNG k-ε湍流模型预测液力透平水力性能具有较高的可信度。选用RNG k-ε湍流模型和CFX17.0，分析透平内速度滑移机理及速度滑移量化指标，进一步对比液力透平和离心泵速度滑移的大小及流动机理。研究发现：液力透平叶轮内存在速度滑移现象，速度滑移导致透平水头降低，并诱发了附着于叶片工作面的旋涡。透平滑移系数随比转速变化而变化，数值在0.2～0.4。比较反转泵液力透平透平工况与泵工况的滑移系数发现：当比转速大于50时，透平工况的滑移系数比泵工况的小，比转速低于50时，出现了透平工况滑移系数高于泵工况的情形。

关键词: 滑移系数, 离心泵, 能量回收, 速度滑移, 液力透平

Abstract: Slip phenomenon is known to strongly influence the performance of pumps as turbines(PAT). In the present work, the standard k-ε model, RNG k-ε model, standard k-ω and SST k-ω model are adopted to simulate the hydraulic performance of PAT, and the experiment values are in a good agreement with CFD result by using RNG k-ε model. Therefore, the slip phenomenon in turbine impeller is studied and the slip factor is estimated for each PAT using RNG k-ε model. Then the slip phenomenon in turbine mode was compared with pump mode. It is observed that slip phenomenon occurs in PAT, and it lead to the head decrease, besides, the vortex flow is generated in PAT's flow passages near pressure side of blade. The slip factor varies with the specific speed of PAT, and its value is 0.2-0.4 approximately. In comparison with pump mode, the slip factor of turbine mode smaller than pump mode when the specific speed above 50, but larger when it below 50.

Key words: centrifugal pump, energy recovery, pumps as turbines, slip, slip factor

中图分类号:

TH311
TH322

王晓晖, 杨军虎, 郭艳磊, 夏正廷, 苗森春. 反转泵液力透平速度滑移机理[J]. 机械工程学报, 2018, 54(24): 189-196.

WANG Xiaohui, YANG Junhu, GUO Yanlei, XIA Zhengting, MIAO Senchun. Research on Slip Phenomenon of Pumps as Turbines[J]. Journal of Mechanical Engineering, 2018, 54(24): 189-196.

参考文献

[1] 杨军虎, 王晓晖. 叶片形状对能量回收水力透平性能的影响[J]. 排灌机械工程学报, 2011, 29(4):287-291. YANG Junhu, WANG Xiaohui. Effect of vane profile on hydraulic energy recovery turbines performance[J]. Journal of Drainage and Irrigation Machinery Engineering, 2011, 29(4):287-291.
[2] 王晓晖,杨军虎,史凤霞. 能量回收液力透平的研究现状及展望[J]. 排灌机械工程学报, 2014, 32(9):742-747. WANG Xiaohui. YANG Junhu, SHI Fengxia. Status and prospect of study on energy recovery hydraulic turbines[J]. Journal of Drainage and Irrigation Machinery Engineering, 2014, 32(9):742-747.
[3] 关醒凡.现代泵理论与设计[M]. 北京:中国宇航出版社, 2011. GUAN Xingfan. Modern pumps theory and design[M]. Beijing:China Astronautic Publishing House, 2011.
[4] LI W G. Effects of flow rate and viscosity on slip factor of centrifugal pump handling viscous oils[J]. International Journal of Rotating Machinery, 2013, 213(6):1-12.
[5] MEMARDEZFOULI M, NOURBAKHSH A. Experimental investigation of slip factors in centrifugal pumps[J]. 2009, 33(5):938-945.
[6] JAIN S V, SWARNKAR A, MOTWANI K H, et al. Effects of impeller diameter and rotational speed on performance of pump running in turbine mode[J]. Energy Conversion and Management, 2015, 89(4):808-824.
[7] GIOSIO D R, HENDERSON A D, WAIKER J M, et al. Design and performance evaluation of pump-as-turbine micro-hydro test facility with incorporated inlet flow control[J]. Renewable Energy, 2015, 78(1):1-6.
[8] BUONO D, FROSINA E, MAZZONE A, et al. Study of a pump as turbine for a hydraulic urban network using a tridimensional CFD modeling methodogy[J]. Energy Procedia, 2015, 82(12):201-208.
[9] YANG S S, KONG F Y, JIANG W M, et al. Effect of impeller trimming influencing pump as turbine[J]. Computers & Fluids, 2012, 67(7):72-78.
[10] SINGH P, NEATMANN F. A consolidated model for the turbine operation of centrifugal pumps[J]. Journal of Engineering for Gas Turbine and Power, 2011, 133(6):1-9.
[11] DERAKHSHAN S, NOURBAKHSH A. Theoretical, numerical and experimental investigation of centrifugal pumps in reverse operation[J]. Experimental Thermal and Fluid Science. 2008, 32(8):1620-1627.
[12] ARDIZZON G, PAVESI G. Optimum incidence angle in centrifugal pumps and radial inflow turbines[J].Journal of Power and Energy, 1998, 212(2):97-107.
[13] VENTRONE G, ARDIZZON G, PAVESI G. Direct and reverse flow conditions in radial flow hydraulic turbomachines[J]. Proceedings of the Institution of Mechanical Engineers. Part A. 2000, 214(A6):635-644.
[14] 史广泰,杨军虎,苗森春. 离心泵用作液力透平叶轮出口滑移系数的计算方法[J]. 农业工程学报, 2014, 30(13):68-77. SHI Guangtai, YANG Junhu, MIAO Senchun. Analytical methods and verification for determining slip factor at impeller outlet of centrifugal pumps as turbines[J]. Transactions of the Chinese Society of Agricultural Engineering, 2014, 30(13):68-77.
[15] 董亮,刘厚林. 叶片泵CFD数值计算实例详解[M]. 北京:机械工业出版社, 2015. DONG Liang, LIU Houlin. CFD numerical calculation examples of vans pump[M]. Beijing:China Machine Press, 2015.
[16] 刘厚林,刘东喜,王勇,等. 三种空化模型在离心泵空化流动计算中的应用评价[J]. 农业工程学报, 2012, 28(16):54-59. LIU Houlin, LIU Dongxi, WANG Yong, et al. Applicative evaluation of three cavitating models on cavitating flow calculation in ce-ntrifugal pump[J]. Transactions of the Chinese Society of Agricultural Engineering, 2012, 28(16):54-59.
[17] 李晓俊,袁寿其,潘中永,等. 离心泵边界层网格的实现及应用评价[J]. 农业工程学报, 2012, 28(20):67-72. LI Xiaojun, YUAN Shouqi, PAN Zhongyong. Realization and application evaluation of near-wall mesh in centrifugal pumps[J]. Transactions of the Chinese Society of Agricultural Engineering, 2012, 28(20):67-72.
[18] 谢龙汉,赵新宇. ANSYS CFX流体分析及仿真[M]. 北京:电子工业出版社, 2013. XIE Longhan, ZHAO Xinyu. ANSYS CFX Fluid analysis and simulation[M]. Beijing:Publishing House of Electronic Industry, 2013.
[19] 周水清,孔繁余,王志强,等. 基于结构化网格的低比转速离心泵性能数值模拟[J]. 农业机械学报, 2011, 42(7):66-69. ZHOU Shuiqing, KONG Fanyu, WANG Zhiqiang, et al. Numerical simulation for low specific-speed centrifugal pump with structured grid[J]. Transactions of the Chinese Society for Agricultural Machinery, 2011, 42(7):66-69.
[20] 赵斌娟,袁寿其,陈汇龙,等. 基于滑移网格研究双流道泵内非定常流动特性[J]. 农业工程学报,2009,25(6):115-119. ZHAO Binjuan, YUAN Shouqi, CHEN Huilong, et al. Unsteady flow characteristics in double-channel pumps based on sliding mesh[J]. Transactions of the Chinese Society of Agricultural Engineering,2009,25(6):115-119.

反转泵液力透平速度滑移机理

Research on Slip Phenomenon of Pumps as Turbines

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	童哲铭, 马鑫航. 基于孪生支持向量回归的多级离心泵外特性曲线预测及设计方法[J]. 机械工程学报, 2024, 60(14): 364-377.
[2]	王翔宇, 郝云晓, 权龙, 葛磊, 刘华坤. 电-液双源混驱装载机举升系统特性研究[J]. 机械工程学报, 2023, 59(7): 41-51.
[3]	张晓虎, 张熊, 张克良, 孙现众, 王凯, 马衍伟. 储能技术在轨道交通再生制动能量回收的应用[J]. 电气工程学报, 2023, 18(2): 210-220.
[4]	梁涛, 权龙, 葛磊, 王永进. 基于电液储能调控的多执行器载荷差异均衡系统特性研究[J]. 机械工程学报, 2023, 59(18): 337-348.
[5]	吴跃忠, 张婷, 费铭昊, 吴登昊, 任芸. 基于QP改进模型的离心泵性能预测方法[J]. 机械工程学报, 2023, 59(13): 280-289.
[6]	陈仲生, 曹军义, 秦朝烨, 陈志文, XIONG Yeping. 汽车悬架同步振动抑制与能量收集综述与展望[J]. 机械工程学报, 2022, 58(20): 3-26.
[7]	姜丙孝, 杨军虎, 王晓晖, 苗森春. 基于RBF-HDMR模型与PSO算法的液力透平叶片优化[J]. 机械工程学报, 2022, 58(12): 283-292.
[8]	贺登辉, 张振铎, 常壮, 郭鹏程, 白博峰. 泡状入流条件下离心泵喘振特性试验研究[J]. 机械工程学报, 2022, 58(10): 289-297.
[9]	林通, 李晓俊, 朱祖超, 谢华东, 胡建新. 离心泵作透平最佳工况点下的瞬态流动特性分析[J]. 机械工程学报, 2021, 57(22): 395-405.
[10]	康娅娟, 刘少军. 深海采矿提升系统研究综述[J]. 机械工程学报, 2021, 57(20): 232-243.
[11]	周维, 刘鸿远, 徐彪, 张雷. 功率分流式混合动力矿用自卸车预测性等效燃油消耗最小控制策略研究[J]. 机械工程学报, 2021, 57(2): 200-209.
[12]	王存金, 董林杰, 李杰, 王兴松, 丁也. 基于人行走能耗分析的踝关节外骨骼设计[J]. 机械工程学报, 2021, 57(19): 79-92.
[13]	陈伟, 项载毓, 钱泓桦, 莫继良. 基于摩擦自激振动升频效应的超低频振动能量收集[J]. 机械工程学报, 2021, 57(15): 160-167.
[14]	王翔宇, 张红娟, 杨敬, 葛磊, 郝云晓, 权龙. 非对称泵控装载机动臂特性研究[J]. 机械工程学报, 2021, 57(12): 258-266,284.
[15]	宋文武, 石建伟, 魏立超, 胡帅, 罗旭, 陈建旭. 高速离心泵回流漩涡及空化特性[J]. 机械工程学报, 2020, 56(4): 95-103.