面向伺服动态特性匹配的轮廓误差补偿控制研究*

doi:10.3901/JME.2017.01.150

摘要/Abstract

摘要：

在多轴数控加工中，轮廓误差直接决定零件最终加工精度。交差耦合控制和任务坐标系法通过估计轮廓误差，并设计轮廓跟踪控制器来提高轮廓精度。这两种方法存在大曲率位置轮廓误差估计精度差，轮廓控制增益整定依赖于工程经验等问题。为此，从伺服轴动态特性匹配出发，提出了一种基于轮廓误差精确计算的轮廓误差补偿控制方法。根据足点定义，采用解析方法快速准确计算轮廓误差。将轮廓误差分量分别补偿到各伺服轴的速度环和转矩环，提高各伺服轴动态特性的匹配程度。采用两维和三维NURBS曲线开展轮廓跟踪试验。试验结果表明：所提出的轮廓误差计算方法可以精确求解轮廓误差;所提出的轮廓误差补偿控制方法不需要建立轮廓误差与伺服跟踪误差间的映射关系，且可通过调整控制器增益定量显著减小轮廓误差。

关键词: 补偿, 轮廓控制, 轮廓误差, 动态特性匹配

Abstract: In multi-axis CNC machining, the final machining precision of the parts is determined directly by the contour error. Cross-coupling controller and task coordinate frame approach can improve the contour accuracy by estimating the contour error and designing the contouring controller. There exist some problems such as the poor contour error estimation accuracy in the large curvature position and contour control gain setting depending on engineering experience with the two methods. To solve this issue, proceeding from the dynamic characteristics matching of the servo axes, a contour error compensation method based on the precise calculation of the contour error is proposed. According to the definition of the foot point, the contour error is calculated quickly and accurately using the analytical method. Then, the contour error component is compensated to every servo axis’s speed loop and torque loop to improve the matching degree of the dynamic characteristics. Finally, the experiments are conducted using the two-dimensional and three-dimensional NURBS curves. The experiment results show that the contour error can be estimated exactly by the proposed contour error calculation method. The proposed contour error compensation method does not need to establish the relationship between the contour error and the tracking errors, and reduce the contour error quantitatively and significantly by adjusting the controller gains.

Key words: compensation, contour error, contouring control, dynamic characteristics matching

李祥飞, 赵欢, 赵鑫, 丁汉. 面向伺服动态特性匹配的轮廓误差补偿控制研究^*[J]. 机械工程学报, 2017, 53(1): 150-156.

LI Xiangfei, ZHAO Huan, ZHAO Xin, DING Han. Research on Contour Error Compensation Method with Matched Servo Dynamic Characteristics[J]. Journal of Mechanical Engineering, 2017, 53(1): 150-156.

参考文献

[1] 孙玉文，郭东明，贾振元. 复杂曲面的测量加工一体化[J]. 科学通报，2015，60(9)：781-791.

SUN Yuwen，GUO Dongming，JIA Zhenyuan. Measuring complex surface machining integration[J]. Chinese Science Bulletin，2015，60(9)：781-791.

[2] SENCER B，ALTINTAS Y，CROFT E. Modeling and control of contouring errors for five-axis machine tools-part I：Modeling[J]. ASME Journal of Manufacturing Science and Engineering，2009，131：031006.

[3] YEH S S，HSU P L. Perfectly matched feedback control and its integrated design for multiaxis motion systems[J]. Trans. of the ASME，Journal of Dynamic Systems，Measurement and Control，2004，126(3)：547-557.

[4] MASORY O. Improving contouring accuracy of NC/CNC systems with additional velocity feed forward loop[J]. Journal of Manufacturing Science and Engineering，1986，108(3)：227-230.

[5] TOMIZUKA M. Zero phase error tracking algorithm for digital control[J]. Trans. of the ASME，Journal of Dynamic Systems，Measurement and Control，1987，109(1)：65-68.

[6] ALTINTAS Y，ERKORKMAZ K，ZHU Wenhong. Sliding mode controller design for high speed feed drives[J]. CIRP Annals-Manufacturing Technology，2000，49(1)：265-270.

[7] CHIU G T C，TOMIZUKA M. Contouring control of machine tool feed drive systems：A task coordinate frame approach[J]. IEEE Trans. Control System Technology，2001，9(1)：130-139.

[8] YAO Bin，HU Chuxiong，WANG Qingfeng. An orthogonal global task coordinate frame for contouring control of biaxial systems[J]. IEEE/ASME Trans. On Mechatronics，2012，17(4)：622-634.

[9] KOREN Y. Cross-coupled biaxial computer controls for manufacturing systems[J]. Trans. of the ASME，Journal of Dynamic Systems，Measurement and Control，1980，102(4)：265-272.

[10] KOREN Y，LO C C. Variable-gain cross-coupling controller for contouring[J]. CIRP Annals-Manufacturing Technology，1991，40(1)：371-374.

[11] UCHIYAMA N. Contouring controller design based on iterative contour error estimation for three-dimensional machining[J]. Robotics and Computer-Integrated Manufacturing，2011，27(4)：802-807.

[12] YANG Jiangzhao，LI Zexiang. A novel contour error estimation for position loop-based cross-coupled control[J]. IEEE/ASME Trans. On Mechatronics，2011，16(4)：643-655.

[13] SHIH Yiti，CHEN Chinsheng，LEE Anchen. A novel cross-coupling control design for bi-axis motion[J]. International Journal of Machine Tools and Manufacture，2002，42：1539-1548.

[14] ZHU Limin，ZHAO Huan，DING Han. Real-time contouring error estimation for multi-axis motion systems using the second-order approximation[J]. International Journal of Machine Tools and Manufacture，2013，68：5-80.

[15] CONWAY J R，ERNESTO C A，FAROUKI R T，et al. Performance analysis of cross-coupled controllers for CNC machines based upon precise real-time contour error measurement[J]. International Journal of Machine Tools and Manufacture，2012，52：30-39.

[16] YEH S S，HSU P L. Perfectly matched feedback control and its integrated design for multiaxis motion systems[J]. ASME Journal of Dynamic Systems，Measurement and Control，2004，126：547-557.

[17] XI X C，POO A N，HONG G S. Improving contouring accuracy by tuning gains for a bi-axial CNC machine[J]. International Journal of Machine Tools and Manufacture，2009，49(5)：395-406.

面向伺服动态特性匹配的轮廓误差补偿控制研究^*

Research on Contour Error Compensation Method with Matched Servo Dynamic Characteristics

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	葛磊, 倪豪, 郝云晓, 赵斌, 苑永亮, 权龙. 新型液压回转-机械直线执行器的死区补偿控制[J]. 机械工程学报, 2024, 60(8): 337-347.
[2]	王淞立, 方续东, 高博楠, 赵立波, 田边, 林启敬, 张仲恺, 饶浩, 李瑜, 蒋庄德. 硅微谐振压力传感器自动增益控制与相位补偿研究[J]. 机械工程学报, 2024, 60(4): 82-91.
[3]	周宁, 姚建勇, 邓文翔. 基于神经网络的比例伺服阀阀芯液动力补偿鲁棒智能控制[J]. 机械工程学报, 2024, 60(4): 126-133.
[4]	王波, 赵星宇, 权龙, 赵斌, 李运帷, 郝云晓. 基于主动压差调控的变增益流量控制原理[J]. 机械工程学报, 2024, 60(4): 134-142.
[5]	杨为, 唐小林, 姜孔明, 付洋, 韩磊. 电动制动助力系统摩擦补偿模型及其控制方法研究[J]. 机械工程学报, 2024, 60(2): 252-261.
[6]	牛善帅, 王军政, 赵江波, 沈伟. 泵控电液伺服系统基于未知死区补偿的自适应鲁棒控制[J]. 机械工程学报, 2024, 60(18): 327-337.
[7]	张德权, 李星奥, 张宁, 宁国松, 韩旭. 工业机器人全域误差场精细化建模方法及其误差补偿策略[J]. 机械工程学报, 2024, 60(13): 316-329.
[8]	张伟, 刘辉, 刘金刚, 严鹏飞, 傅兵. 机电复合传动主谐次扰动相位自适应补偿方法[J]. 机械工程学报, 2024, 60(13): 354-365.
[9]	周健, 郑联语, 樊伟, 张学鑫, 曹彦生. 工业机器人定位误差在线自适应补偿[J]. 机械工程学报, 2023, 59(5): 53-66.
[10]	张鹏, 祝长生. 基础摆动条件下主动电磁轴承-柔性转子系统的稳定性[J]. 机械工程学报, 2023, 59(5): 167-179.
[11]	张冰鑫, 刘侃, 李跃, 胡伟, 黄庆, 陈泳丹. 基于累积误差补偿的永磁同步电机低速插值控制策略^*[J]. 电气工程学报, 2023, 18(3): 145-153.
[12]	万晓东, 马平, 万东红. 基于DG无功参与的配电网综合无功优化[J]. 电气工程学报, 2023, 18(3): 260-267.
[13]	胡继磊, 刘雪粲, 江宁强, 葛晨阳, 邱殿成. 含SVC电力系统的IPEBS法暂态稳定分析^*[J]. 电气工程学报, 2023, 18(3): 277-284.
[14]	郭建英, 梁晋, 刘建泽, 滕光蓉, 石炜, 刘良宝. 航空发动机机匣多边并联加载装置设计及精度分析[J]. 机械工程学报, 2023, 59(23): 23-32.
[15]	李洲龙, 王锐, 范哲, 朱利民. 大气等离子体射流加工的热误差在线补偿方法[J]. 机械工程学报, 2023, 59(21): 75-84.