大型复杂型面铝合金翻边件电磁成形塑性流动行为研究

›› 2013, Vol. 49 ›› Issue (24): 24-29.

扫码分享

大型复杂型面铝合金翻边件电磁成形塑性流动行为研究

黄亮;骆文勇;刘贤龙;李建军

华中科技大学材料成形与模具技术国家重点实验室;华中科技大学材料科学与工程学院

发布日期:2013-12-20

Research on Plastic Flow Behaviors for Hole Flanging Part of Aluminum Alloy with Large Complicated Profiles by Electromagnetic Forming

HUANG Liang;LUO Wenyong;LIU Xianlong;LI Jianjun

State Key Laboratory of Materials Processing and Die & Mould Technology, Huazhong University of Science and Technology College of Materials Science and Engineering, Huazhong University of Science and Technology

Published:2013-12-20

摘要/Abstract

摘要： 大型复杂型面铝合金翻边件电磁成形是一个电磁场和结构场耦合作用下的复杂塑性成形过程。由于大型复杂型面的影响，使得铝合金翻边件在电磁成形过程中的塑性流动行为与传统带凸模翻边成形不同。基于松散耦合法建立耦合电磁场和结构场的大型复杂型面铝合金翻边件电磁成形有限元模型，研究采用1层、2层和3层平板线圈电磁翻边下的板料塑性流动行为，并采用试验研究揭示了不同压边力控制下板料法兰部分塑性流动规律。结果表明，当采用3层平板线圈时，翻边件的复杂型面部分完全贴膜，法兰部分材料进入凹模腔的部分更多，促使板料发生更多的塑性流动；不同压边力控制下，法兰部分由塑性流动产生不同的工件形式，在压边力不足时，法兰部分产生明显的起皱现象；通过合理的压边力控制，可得到贴膜性良好的大型复杂型面铝合金翻边件。

关键词: 大型复杂型面, 电磁成形, 翻边件, 塑性流动

Abstract: Hole flanging part of aluminum alloy with large complicated profiles by electromagnetic forming is a complex metal forming process coupling electromagnetic field and constructive field. Due to the effects of large complicated profiles, plastic flow behaviors during the forming process are different from traditional flanging forming. A finite element model for hole flanging part of aluminum alloy with large complicated profiles by electromagnetic forming is established based on loose coupling simulation method, and then plastic flow behaviors on condition of one layer flat coil, two layers flat coil and three layer flat coil are investigated, and subsequently plastic flow rules of flange parts under different pressures are revealed by experiments. The results are as follows: Large complicated profiles are completed closed to female die surfaces on condition of three layer flat coil, flange parts are put into female die and plastic flow phenomenon is more obvious; flange parts are grown to different modes under different pressures, and obvious wrinkling phenomenon for flange parts appear when pressures are less; hole flanging part of aluminum alloy with large complicated profiles more closed to female die surfaces is obtained by controls of reasonable pressures.

Key words: Electromagnetic forming, Hole flanging part, Large complicated profiles, Plastic flow

中图分类号:

TG391

黄亮;骆文勇;刘贤龙;李建军. 大型复杂型面铝合金翻边件电磁成形塑性流动行为研究[J]. , 2013, 49(24): 24-29.

HUANG Liang;LUO Wenyong;LIU Xianlong;LI Jianjun. Research on Plastic Flow Behaviors for Hole Flanging Part of Aluminum Alloy with Large Complicated Profiles by Electromagnetic Forming[J]. , 2013, 49(24): 24-29.

[1]	王刚, 谷诤巍, 于歌, 李欣. 热成形工艺条件下7075-H18铝合金板材塑性流动行为的本构建模[J]. 机械工程学报, 2024, 60(2): 188-196.
[2]	党嘉强, 安庆龙, 李宇罡, 明伟伟, 王浩伟, 陈明. 300M钢超声滚压表面形貌演变机理和试验表征[J]. 机械工程学报, 2024, 60(15): 358-367.
[3]	杨智勇, 李武鹏, 李志强, 刘小龙, 李卫京. 搅拌摩擦焊多平面搅拌头对材料流动行为的影响[J]. 机械工程学报, 2022, 58(6): 81-90.
[4]	崔晓辉;莫健华;王波;何文治. 基于松散耦合法的电磁平板成形3D有限元仿真[J]. , 2011, 47(16): 45-51.
[5]	孟正华;黄尚宇;胡建华;夏志林;夏晓锋. 镁合金板材温热电磁复合成形试验研究[J]. , 2011, 47(10): 38-42.
[6]	柯黎明;潘际銮;邢丽;王善林. 搅拌摩擦焊焊缝金属塑性流动的抽吸—挤压理论[J]. , 2009, 45(4): 89-94.
[7]	于海平;李春峰;李忠. 基于FEM的电磁缩径耦合场数值模拟[J]. , 2006, 42(7): 231-234.
[8]	鄂大辛;水野高爾. 非回转对称拉深中材料流动变形规律的研究[J]. , 2003, 39(4): 49-52，8.
[9]	初红艳;费仁元;陆辛;杨鲁义. 电磁成形中板料厚度与变形深度的关系[J]. , 2003, 39(3): 62-65.
[10]	于连仲;朱炳钦;宋福民;熊海芝;陈亦伟. 框架零件电磁成形变形的研究[J]. , 1995, 31(1): 72-77.
[11]	关廷栋;孙胜;赵国群. 杯——杆型复合挤压过程的上限元模拟[J]. , 1988, 24(3): 35-43.

大型复杂型面铝合金翻边件电磁成形塑性流动行为研究

Research on Plastic Flow Behaviors for Hole Flanging Part of Aluminum Alloy with Large Complicated Profiles by Electromagnetic Forming

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 11

编辑推荐

Metrics

本文评价