面向薄壁零件加工变形与振动控制的智能装夹技术研究进展

doi:10.3901/JME.2021.17.021

机械工程学报 ›› 2021, Vol. 57 ›› Issue (17): 21-34.doi: 10.3901/JME.2021.17.021

• 特邀专栏：智能制造前沿及应用 • 上一篇下一篇

扫码分享

面向薄壁零件加工变形与振动控制的智能装夹技术研究进展

吴宝海^1,2, 郑志阳^1,2, 张阳^1,2, 张莹^1,2, 郑天飞^1,2

1. 西北工业大学航空发动机高性能制造工信部重点实验室西安 710072;
2. 西北工业大学航空发动机先进制造技术教育部工程研究中心西安 710072

收稿日期:2020-12-28 修回日期:2021-03-26 发布日期:2021-11-16
通讯作者: 张莹(通信作者),女,1981年出生,博士,副研究员。主要研究方向为计算机辅助几何设计、多轴数控加工及自适应加工技术。E-mail:zhangyingcdim@nwpu.edu.cn
作者简介:吴宝海,男,1975年出生,教授,博士研究生导师。主要研究方向为复杂结构多轴数控加工技术、自适应智能加工、智能制造。E-mail:wubaohai@nwpu.edu.cn;郑志阳,男,1997年出生,硕士研究生。主要研究方向为复杂薄壁结构智能装夹技术、装夹布局优化。E-mail:zhengzhiyang@mail.nwpu.edu.cn
基金资助:
国家重点研发计划（2020YFB1710400）和陕西省自然科学基础研究计划面上（No.2021JM-054）资助项目。

Intelligent Clamping Technology for Machining Deformation and Vibration Control of Thin-wall Parts: A Review of Recent Progress

WU Baohai^1,2, ZHENG Zhiyang^1,2, ZHANG Yang^1,2, ZHANG Ying^1,2, ZHENG Tianfei^1,2

1. Key Laboratory of High Performance Manufacturing for Aero Engine, Northwestern Polytechnical University, Ministry of Industry and Information Technology, Xi'an 710072;
2. Engineering Research Center of Advanced Manufacturing Technology for Aero Engine, Northwestern Polytechnical University, Ministry of Education, Xi'an 710072

Received:2020-12-28 Revised:2021-03-26 Published:2021-11-16

摘要/Abstract

摘要： 薄壁零件由于其弱刚性导致的切削加工变形与振动极大地影响着产品的最终质量。合理的装夹能够控制加工变形与振动，有效提升薄壁零件的加工稳定性。随着新型传感与控制算法的发展，现代夹具逐渐向智能化方向发展，集成夹紧力控制、变形补偿、实时监测、动态反馈调整等功能于一体的智能夹具应运而生，并成为学术界和工业界的研究热点。本文梳理了薄壁零件装夹方案优化方法及其加工辅助支撑技术、综述了当前关于智能夹具架构、具体应用及其控制策略的国内外研究现状，最后总结了当前装夹方案优化及智能夹具研究方面所存在的问题并提出下一步的研究方向。

关键词: 薄壁零件, 装夹优化, 辅助支撑, 智能夹具

Abstract: The machining deformation and vibration of thin-walled parts due to inherent weak rigidity greatly affect the final quality of products. Reasonable clamping can control the machining deformation and vibration, improve the machining stability of thin-walled parts effectively. With the development of new sensing and control algorithms, modern fixtures are gradually developing towards the direction of intelligence. Intelligent fixtures integrated clamping force control, deformation compensation, real-time monitoring, dynamic feedback adjustment and other functions have emerged and became new research hotspot in academia and industry. Therefore, the clamping scheme optimization method and machining auxiliary support technology of thin-walled parts is combed in this paper. The current research status at home and abroad about system architecture, specific application and control strategy of intelligent fixture are also reviewed systematically. Ultimately, the extant problems in clamping scheme optimization and intelligent fixture are concluded and the potential development trends are proposed.

Key words: thin-wall parts, clamping optimization, auxiliary support, intelligent fixture

中图分类号:

V261
TH161

吴宝海, 郑志阳, 张阳, 张莹, 郑天飞. 面向薄壁零件加工变形与振动控制的智能装夹技术研究进展[J]. 机械工程学报, 2021, 57(17): 21-34.

WU Baohai, ZHENG Zhiyang, ZHANG Yang, ZHANG Ying, ZHENG Tianfei. Intelligent Clamping Technology for Machining Deformation and Vibration Control of Thin-wall Parts: A Review of Recent Progress[J]. Journal of Mechanical Engineering, 2021, 57(17): 21-34.

参考文献

[1] RAI J K,XIROUCHAKIS P. Finite element method based machining simulation environment for analyzing part errors induced during milling of thin-walled components[J]. International Journal of Machine Tools & Manufacture,2008,48(6):629-643.
[2] CHEN W,XUE J,TANG D,et al. Deformation prediction and error compensation in multilayer milling processes for thin-walled parts[J]. International Journal of Machine Tools and Manufacture,2009,49(11):859-864.
[3] 陈冰,杨宝通,牛智炀,等. 面向航空发动机薄壁零件加工的自适应夹具设计现状与进展[J]. 航空制造技术,2019,62(7):14-24. CHEN Bing,YANG Baotong,NIU Zhiyang,et al. Adaptive fixture designing of thin-walled aero-engine workpiece:A survey of the state of art[J]. Aeronautical manufacturing technology,2019,62(7):14-24.
[4] ARNAUD L,GONZALO O,SEGUY S,et al. Simulation of low rigidity part machining applied to thin-walled structures[J]. International Journal of Advanced Manufacturing Technology,2011,54(5-8):479-488.
[5] BAKKER O J,PAPASTATHIS T,POPOV A A,et al. Active fixturing:Literature review and future research directions[J]. International Journal of Production Research,2013,51(11):3171-3190.
[6] 王少锋,洪军,王建国,等. 大型薄壁件的多点支承/定位方法研究[J]. 西安交通大学学报,2016,50(6):122-129. WANG Shaofeng,HONG Jun,WANG Jianguo,et al. Multi-point location method of large-scale thin-wall component[J]. Journal of Xi'an Jiaotong University,2016,50(6):122-129.
[7] 张远远,王仲奇,康永刚. 基于多点技术的柔性支撑定位方法研究[J]. 机械设计与制造工程,2013,42(5):7-11. ZHANG Yuanyuan,WANG Zhongqi,KANG Yonggang. Flexible supporting and positioning method based on multi-point technology[J]. Machine Design and Manufacturing Engineering,2013,42(5):7-11.
[8] KANG Y,Rong J C,YANG J,et al. Computer-aided fixture design verification,assembly[J]. Automation,2002,22(4):350-359.
[9] CAI W,HU S J,YUAN J X. A variational method of robust fixture configuration design for 3-D workpieces[J]. Journal of Manufacturing Science and Engineering-Transactions of the ASME,1997,119(4A):593-602.
[10] LI B,MELKOTE S N. Improved workpiece location accuracy through fixture layout optimization[J]. International Journal of Machine Tools & Manufacture,1999,39(6):871-883.
[11] 秦国华,张卫红. 基于最小范数原理的夹紧力优化设计算法[J]. 中北大学学报,2011,32(4):442-447. QIN Guohua,ZHANG Weihong. An optimal method to clamping force determination based on the minimum norm principle[J]. Journal of North University of China,2011,32(4):442-447.
[12] WANG H M,QIN G H,WU Z X,et al. A workpiece stability-based iterative planning of clamping forces for fixturing layout specification of a complex workpiece[J]. International Journal of Advanced Manufacturing Technology,2019,103(5-8):2017-2035.
[13] 陈宝林. 最优化理论与算法[M]. 北京:清华大学出版社,2005. CHEN Baolin. Optimization theory and algorithm[M]. Beijing:Tsinghua University Press,2005.
[14] 秦国华,何志芬,王华敏,等. 基于动力学与遗传算法的工件位置偏离预测与控制方法[J]. 机械工程学报,2017,53(1):110-120. QIN Guohua,HE Zhifen,WANG Huamin,et al. Prediction and control of workpiece position deviation based on dynamics and genetic algorithm[J]. Journal of Mechanical Engineering,2017,53(1):110-120.
[15] 秦国华,王子琨,吴竹溪,等. 基于表面网格离散化与遗传算法的复杂工件装夹布局规划方法[J]. 机械工程学报,2016,52(13):195-203. QIN Guohua,WANG Zikun,WU Zhuxi,et al. A planning method of fixturing layout for complex workpieces based on surface discretization and genetic algorithm[J]. Journal of Mechanical Engineering,2016,52(13):195-203.
[16] CAI W,HU S J,YUANL J X. Deformable sheet metal fixturing:Principles,algorithms,and simulations[J]. Journal of Manufacturing Science and Engineering-Transactions of the ASME,1996,118(3):318-324.
[17] 陈禹至,陈蔚芳,施圣杰. 一种薄壁件柔性多点加工工装布局优化技术[J]. 机械制造与自动化,2018,47(5):61-63. CHEN Yuzhi,CHEN Weifang,SHI Shengjie. multi-point flexible tooling layout optimization technique for thin-walled workpieces[J]. Mechanical manufacture and Automation,2018,47(5):61-63.
[18] WANG Y,CHEN X,LIU Q,et al. Optimization of machining fixture layout under multi-constraints[J]. International Journal of Machine Tools and Manufacture,2006,46(12-13):1291-1300.
[19] WANG H,HUANG L J,YAO C,et al. Integrated analysis method of thin-walled turbine blade precise machining[J]. International Journal of Precision Engineering & Manufacturing,2015,16(5):1011-1019.
[20] 王运巧,梅中义,范玉青. 薄壁弧形件装夹布局有限元优化[J]. 机械工程学报,2005(6):214-217,223. WANG Yunqiao,MEI Zhongyi,FAN Yuqing. Finite element optimization of the clamping layout of thin-walled arc-shaped part[J]. Chinese Journal of Mechanical Engineering,2005(6):214-217,223.
[21] 何志芬. 夹具装夹布局动力学分析与优化[D]. 南昌:南昌航空大学,2016. HE Zhifen. The prediction of clamping deformation and the optimization method of fixture layout for the thin-wall workpiece[D]. Nanchang:Nanchang Hangkong University,2016.
[22] VASUNDARA M,PADMANABAN K P. Recent developments on machining fixture layout design,analysis,and optimization using finite element method and evolutionary techniques[J]. International Journal of Advanced Manufacturing Technology,2014,70(1-4):79-96.
[23] 杨阳. 基于遗传算法和有限单元法的夹具布局优化[D]. 大连:大连理工大学,2015. YANG Yang. Fixture layout optimization based on genetic algorithm and finite element method[D]. Dalian:Dalian University of Technology,2015.
[24] KULANKARA K,SATYANARAYANA S,MELKOTE S N. Iterative fixture layout and clamping force optimization using the genetic algorithm[J]. Journal of Manufacturing Science and Engineering,2002,124(1):119-125.
[25] 路冬. 航空整体结构件加工变形预测及装夹布局优化[D]. 济南:山东大学,2007. LU Dong. Deformation prediction and fixture layout optimization of aerospace monolithic components[D]. Jinan:Shandong University,2007.
[26] 周孝伦,张卫红,秦国华,等. 基于遗传算法的夹具布局和夹紧力同步优化[J]. 机械科学与技术,2005(3):339-342. ZHOU Xiaolun,ZHANG Weihong,QIN Guohua,et al. On optimizing fixture layout and clamping force simultaneously using genetic algorithm[J]. Mechanical Science and Technology,2005(3):339-342.
[27] 陈蔚芳,倪丽君,王宁生. 夹具布局和夹紧力的优化方法研究[J]. 中国机械工程,2007(12):1413-1417. CHEN Weifang,NI Lijun,WANG Ningsheng. Investigation on optimization method for fixture layout and clamping forces[J]. China Mechanical Engineering,2007(12):1413-1417.
[28] 许晓宇,赵晓慈. 夹紧顺序、夹具布局和夹紧力对装夹变形影响与同步优化分析研究[J]. 图学学报,2016,37(1):20-24. XU Xiaoyu,ZHAO Xiaoci. Clamping sequence,fixture layout and clamping force on machining deformation and synchronous optimization analysis[J]. Journal of Graphics,2016,37(1):20-24.
[29] HOSSEIN H,VAHID A,MOHSEN S,et al. Simultaneous fixturing layout and sequence optimization based on genetic algorithm and finite element method[J]. International Journal of Advanced Manufacturing Technology,2018,97:3191-3204.
[30] 许稚委. 基于自适应夹紧力的飞机结构件加工变形研究[D]. 南昌:南昌航空大学,2017. XU Zhiwei. Research on deformation of aircraft structural parts based on adaptive clamping force[D]. Nanchang:Nanchang Hangkong University,2017.
[31] BAI X,HU F,HE G Y,et al. A memetic algorithm for multi-objective fixture layout optimization[J]. Proceedings of the Institution of Mechanical Engineers,Part C:Journal of Mechanical Engineering Science,2015,229(16):3047-3058.
[32] DOU J,WANG X,WANG L. Machining fixture layout optimization under dynamic conditions based on evolutionary techniques[J]. International Journal of Production Research,2012,50(14-16):4294-4315.
[33] 王仲奇,李诚,杨勃,等. 基于花授粉算法的曲面薄壁件定位布局优化[J]. 中国机械工程,2017,28(18):2231-2236. WANG Zhongqi,LI Cheng,YANG Bo,et a. Fixture locating layout optimization of curved thin-walled parts based on FDA[J]. China Mechanical Engineering,2017,28(18):2231-2236.
[34] XING Y F,HU M,ZENG H,et al. Fixture layout optimization based on a non-domination sorting social radiation algorithm for auto-body parts[J]. International Journal of Production Research,2015,53(11):3475-3490.
[35] XING Y F. Fixture layout design of sheet metal parts based on global optimization algorithms[J]. Journal of Manufacturing Science and Engineering,2017,139(10):1-10.
[36] 韩忠华. Kriging模型及代理优化算法研究进展[J]. 航空学报,2016,37(11):3197-3225. HAN Zhonghua. Kriging surrogate model and its application to design optimization:A review of recent progress[J]. Chinese Journal of Aeronautics,2016,37(11):3197-3225.
[37] SUNDARARAMAN KA,PADMANABAN KP,SABAREESWARAN M. Optimization of machining fixture layout using integrated response surface methodology and evolutionary techniques[J]. Proceedings of the Institution of Mechanical Engineers,Part C:Journal of Mechanical Engineering Science,2015,230(13):2245-2259.
[38] 于金,王胤棋. 多元非线性回归的非对称薄壁件装夹位置优化[J]. 机床与液压,2017,45(23):142-145. YU Jin,WANG Yinqi. Clamping position optimization of asymmetric thin-walled part by multi-variate nonlinear regression[J]. Machine Tool & Hydraulics,2017,45(23):142-145.
[39] 于金,王胤棋. 大型曲面薄壁件多点柔性工装装夹布局优化[J]. 工具技术,2017,51(10):83-87. YU Jin,WANG Yinqi. Optimization of multi-point flexible fixture clamping layout for large size curved thin-walled part[J]. Tool Technology,2017,51(10):83-87.
[40] 秦国华,赵旭亮,吴竹溪. 基于神经网络与遗传算法的薄壁件多重装夹布局优化[J]. 机械工程学报,2015,51(1):203-212. QIN Guohua ZHAO Xuliang,WU Zhuxi. Optimization of multi-fixturing layout for thin-walled workpiece based on neural network and genetic algorithm[J]. Journal of mechanical engineering,2015,51(1):203-212.
[41] 吴竹溪,秦国华. 基于进化神经网络的薄壁件加工变形预测与抑制方法[J]. 南昌航空大学学报,2020,34(3):80-87. WU Zhuxi,QIN Guohua. Optimized neural network based prediction and control of machining deformation for thin-walled workpieces[J]. Journal of Nanchang Hangkong University,2020,34(3):80-87.
[42] 刘玉梅. 薄板件切削回弹变形机理及装夹优化方法研究[D]. 济南:山东大学,2012. LIU Yumei. Research on deformation mechanism of spring back induced by cutting thin part and optimization of fixture[D]. Jinan:Shandong University,2012.
[43] SELVAKUMAR S,ARULSHRI K P,PADMANABAN K P,et al. Design and optimization of machining fixture layout using ANN and DOE[J]. The International Journal of Advanced Manufacturing Technology,2013,65(9-12):1573-1586.
[44] WANG Z Q,YANG B,KANG Y G,et al. Development of a prediction model based on RBF neural network for sheet metal fixture locating layout design and optimization[J]. Computational Intelligence and Neuroscience,2016,2016:1-6.
[45] 杨元,王仲奇,杨勃,等. 基于SVR的航空薄壁件夹具布局优化预测模型[J]. 计算机集成制造系统,2017,23(6):1302-1309. YANG Yuan,WANG Zhongqi,YANG Bo,et al. Prediction model for aeronautical thin-walled part fixture layout optimization based on SVR[J]. Computer Integrated Manufacturing Systems,2017,23(6):1302-1309.
[46] YANG B,WANG Z Q,YANG Y,et al. Optimum fixture locating layout for sheet metal part by integrating kriging with cuckoo search algorithm[J]. The International Journal of Advanced Manufacturing Technology,2017,91(1-4):327-340.
[47] IWABE H,MIZUOCHI M,YOKOYAMA K. High accurate machining of thin wall shape workpiece by end mill:proposal of twin spindle type machining and some experiments[J]. Transactions of Japan Society of Mechanical Engineers,1999,65(632):1719-1724.
[48] FEI J X,LIN B,YAN S,et al. Chatter mitigation using moving damper[J]. Journal of Sound & Vibration,2017,410:49-63.
[49] LIU C,SUN J. LI Y,et al. Investigation on the milling performance of titanium alloy thin-walled part with air jet assistance[J]. The International Journal of Advanced Manufacturing Technology,2018,95:2865-2874.
[50] 刘随建,刘健伟,吴志新,等. 一种薄壁空间曲面零件防止切削变形的辅助加工装置:中国,CN201110396785.5[P]. 2013-06-05. LIU Suijian,LIU Jianwei,WU Zhixin,et al. An auxiliary machining device for preventing cutting deformation of thin-wall space curved parts:China,CN201110396785.5[P]. 2013-06-05.
[51] 张定华,张笑凡,罗明,等. 航空发动机叶片加工在线测量用组合式夹具:中国,CN201410129372.4[P],2014-07-09. ZHANG Dinghua,ZHANG Xiaofan,LUO Ming,et al. Modular fixture for online measurement of aero engine blade machining:China,CN201410129372.4[P],2014-07-09.
[52] WU D,WANG H,PENG J,et al. Machining fixture for adaptive CNC machining process of near-net-shaped jet engine blade[J]. Chinese Journal of Aeronautics,2020,33(04):1311-1328.
[53] WANG H,HUANG L,YAO C,et al. Integrated analysis method of thin-walled turbine blade precise machining[J]. International Journal of Precision Engineering & Manufacturing,2015,16:1011-1019.
[54] LX451,STARRAG[EB/OL].[2020-10-20]. https://www.starrag.com/zh-cn/machine/lx-451/33.
[55] 王娇. 面向加工变形控制的叶片辅助支撑技术研究[D]. 西安:西北工业大学,2019. WANG Jiao. Research on auxiliary support technology for blade machining deformation control[D]. Xi'an:Northwestern Polytechnical University,2019.
[56] 王胤棋. 基于辅助支撑的机匣加工变形研究[D]. 沈阳:沈阳航空航天大学,2018. WANG Yinqi. Research on machining deformation of casing based on auxiliary support[D]. Shenyang:Shenyang Aerospace University,2018.
[57] 周泽斌. 薄壁结构件加工变形机理及夹具优化设计方法研究[D]. 上海:东华大学,2011. ZHOU Zebin. Deformation prediction and fixture layout optimization of thin walled workpiece[D]. Shanghai:Donghua University,2011.
[58] 崔惠婷,陈蔚芳,冯婷. 装夹优化抑制薄壁件加工振动研究[J]. 组合机床与自动化加工技术,2016(5):138-142. CUI Huiting,CHEN Weifang,FENG Ting. The study on vibration suppression for thin-walled parts based on fixture optimization[J]. Modular Machine Tool & Automatic Manufacturing Technique,2016(5):138-142.
[59] ZENG S S,WAN X J,et al. A novel approach to fixture design on suppressing machining vibration of flexible workpiece[J]. International Journal of Machine Tools & Manufacture,2012,58:29-43.
[60] DO M D,SON Y,CHOI H,et al. Optimal workpiece positioning in flexible fixtures for thin-walled components[J]. Computer-aided Design,2018,95:14-23.
[61] 张志杰,韩子渊,张占辉,等. 曲面薄壁零件的仿形装夹优化研究[J]. 机械工程师,2015(9):117-119. ZHANG Zhijie,HAN Ziyuan,ZHANG Zhanhui,et al. Research on optimal design of fixture for thin wall parts with curved surfaces[J]. Mechanical Engineer,2015(9):117-119.
[62] 李尚政,刘宏. 弱刚度件加固装夹技术研究[J]. 组合机床与自动化加工技术,2003(11):5-7. LI Shangzheng,LIU Hong. Research on reinforce fixture technologies of the weak rigidity workpiece[J]. Modular Machine Tool & Automatic Manufacturing Technique,2003(11):5-7.
[63] GAO B,SUN J,LI J F. Research on machining accuracy in milling Ti6Al4V thin-walled component with paraffin reinforcement[J]. Applied Mechanics and Materials,2013,268-270:504-509.
[64] WANG Y F,WONG Y S,FUH J Y H. Off-line modelling and planning of optimal clamping forces for an intelligent fixturing system[J]. International Journal of Machine Tools Manufacture,1999,39(2):253-271.
[65] MOHRING H,WIEDERKEHR P. Intelligent fixtures for high performance machining[J]. Procedia CIRP,2016,46:383-390.
[66] MERVYN F,KUMAR A S,NEE A Y,et al. An adaptive fixture design system for integrated product and process design[C]//IEEE International Conference on Automation Science & Engineering. IEEE,2005:87-92.
[67] NEE A Y C,KUMAR A S,Tao Z J. An intelligent fixture with a dynamic clamping scheme[J]. Proceedings of the Institution of Mechanical Engineers,Part B:Journal of Engineering Manufacture,2000,214(3):183-196.
[68] GONZALO O,SEARA J M,GURUCETA E,et al. A method to minimize the workpiece deformation using a concept of intelligent fixture[J]. Robotics and Computer-integrated Manufacturing,2017,48:209-218.
[69] LUO M,ZHANG X F,ZHANG D H,et al. On-line compressor blade stiffness enhancement in multi-axis machining process by controlling of tension force[J]. Ifac Papers Online,2015,48(3):664-667.
[70] BAKKER O J. Control methodology and modelling of active fixtures[D]. Nottingham:University of Nottingham,2010.
[71] PAPASTATHIS T. Modelling and design methodology for fully-active fixtures[D]. Nottingham:University of Nottingham,2011.
[72] 王斌利,李迎光,郝小忠,等. 复杂结构件数控加工浮动装夹自适应控制方法[J]. 航空制造技术,2017(10):64-69. WANG Binli,LI Yingguang,HAO Xiaozhong,et al. An adaptive control method of floating fixture for NC machining of complex structural parts[J]. Aeronautical Manufacturing Technology,2017(10):64-69.
[73] SUN W Y,LUO M,ZHANG D H. Machining vibration monitoring based on dynamic clamping force measuring in thin-walled components milling[J]. The International Journal of Advanced Manufacturing Technology,2020,107:2211-2226.
[74] BRECHER C,ESSER M,WITT S. Interaction of manufacturing process and machine tool[J]. CIRP Annals,2009,58(2):588-607.
[75] ALTINTAS Y,WECK M. Chatter stability of metal cutting and grinding[J]. CIRP Annals,2004,53(2):619-642.
[76] GROSSI N,SCIPPA A,SALLESE L,et al. Spindle speed ramp-up test:A novel experimental approach for chatter stability detection[J]. International Journal of Machine Tools & Manufacture,2015,89:221-230.
[77] RIVERO A. Thin-wall machining of light alloys:A review of models and industrial approaches[J]. Materials,2019,12(12):2012.
[78] MONTEVECCHI F,GROSSI N,SCIPPA A,et al. Improved RCSA technique for efficient tool-tip dynamics prediction[J]. Precision Engineering,2016,44:152-162.
[79] 张钊. 薄壁结构铣削过程颤振分析及抑制研究[D]. 上海:上海交通大学,2018. ZHANG Zhao. Chatter analysis and mitigation for the milling of thin-walled structure[D]. Shanghai:Shanghai Jiaotong University,2018.
[80] CLAEYSSEN F,LHERMET N,MAILLARD T,et al. Magnetostrictive actuators compared to piezoelectric actuators[J]. Proceedings of SPIE,2003,4763:194-200.
[81] 江浩. 铣削加工振动主动控制[D]. 上海:上海交通大学,2009. JIANG Hao. Active vibration control in milling[D]. Shanghai:Shanghai Jiaotong University,2009.
[82] SALLESE L,GROSSI N,TSAHALIS J,et al. Intelligent fixtures for active chatter control in milling[J]. Procedia CIRP,2016,55:176-181.
[83] MOHRING H,WIEDERKEHR P,LEREZ C,et al. Sensor integrated CFRP structures for intelligent fixtures[J]. Procedia Technology,2016,26:120-128.
[84] BRECHER C,MANOHARAN D,LADRA U,et al. Chatter suppression with an active workpiece holder[J]. Production Engineering,2010,4(2-3):239-245.
[85] ABELE E,HANSELKA H,HAASE F,et al. Development and design of an active work piece holder driven by piezo actuators[J]. Production Engineering,2008,2(4):437-442.
[86] YANG Y,XU D,LIU Q. Vibration suppression of thin-walled workpiece machining based on electromagnetic induction[J]. Materials and Manufacturing Processes,2015,30(7):829-835.
[87] Innoclamp GmbH,Stabilisierendes Blisker Spannsystem[EB/OL].[2020-10-20]. https://www.innoclamp.de/blisker.
[88] HAO X,LI Y G,CHEN G X,et al. 6+X locating principle based on dynamic mass centers of structural parts machined by responsive fixtures[J]. International Journal of Machine Tools and Manufacture,2018,125:112-122.
[89] WANG S,SONG Q,LIU Z. Vibration suppression of thin-walled workpiece milling using a time-space varying PD control method via piezoelectric actuator[J]. The International Journal of Advanced Manufacturing Technology,2019,105:2843-2856.
[90] CHEN P,ZHAI J,ZHANG X,et al. Research on active vibration control of thin-walled workpiece in milling based on voice coil motor[J]. Springer Berlin Heidelberg,2013,8103:503-512.
[91] SALLESE L,SCIPPA A,GROSSI N,et al. Investigating actuation strategies in active fixtures for chatter suppression[J]. Procedia CIRP,2016,46:311-314.
[92] SALLESE L,GROSSI N,SCIPPA A,et al. Numerical investigation of chatter suppression in milling using active fixtures in open-loop control[J]. Journal of Vibration and Control,2018,24(9):1757-1773.
[93] SALLESE L,INNOCENTI G,GROSSI N,et al. Mitigation of chatter instabilities in milling using an active fixture with a novel control strategy[J]. The International Journal of Advanced Manufacturing Technology,2017,89(9):2771-2787.
[94] PARUS A,POWALKA B,MARCHELEK K,et al. Active vibration control in milling flexible workpieces[J]. Journal of Vibration and Control,2013,19(7):1103-1120.
[95] TAVAKOLPOUR A R,MAILAH M,DARUS I Z,et al. Self-learning active vibration control of a flexible plate structure with piezoelectric actuator[J]. Simulation Modelling Practice and Theory,2010,18(5):516-532.
[96] RASHID A,NICOLESCU C M. Active vibration control in palletized workholding system for milling. International Journal of Machine Tools & Manufacture,2006,46(12):1626-1636.
[97] FORD D,MYERS A,HAASE F,et al. Active vibration control for a CNC milling machine[J]. Proceedings of the Institution of Mechanical Engineers,Part C:Journal of Mechanical Engineering Science,2013(2):230-245.
[98] LONG X,JIANG H,MENG G. Active vibration control for peripheral milling processes[J]. Journal of Materials Processing Technology,2013,213(5):660-670.
[99] 郑平旭,江浩,龙新华,等. 基于H_∞的铣削加工振动主动控制[J]. 振动与冲击,2014,33(5):31-36. ZHENG Pingxu,JIANG Hao,LONG Xinhua,et al. Active vibration control of milling processes based on H_∞[J]. Journal of Vibration and Shock,2014,33(5):31-36.
[100] PAUL S,MORALES-MENENDEZ R. Active control of chatter in milling process using intelligent PD/PID control[J]. IEEE Access,2018,6:72698-72713.
[101] 张兴武,刘金鑫,陈雪峰,等. 基于神经网络的薄壳多目标振动优化控制研究[J]. 机械工程学报,2016,52(9):56-64. ZHANG Xingwu,LIU Jinxin,CHEN Xuefeng,et al. Neural network based multi-objective active vibration optimization[J]. Journal of Mechanical Engineering,2016,52(9):56-64.

面向薄壁零件加工变形与振动控制的智能装夹技术研究进展

Intelligent Clamping Technology for Machining Deformation and Vibration Control of Thin-wall Parts: A Review of Recent Progress

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 3

编辑推荐

Metrics

本文评价

[1]	陈鹏飞, 李祥飞, 何显铭, 蔡元昊, 赵欢, 丁汉. 基于薄壁零件刚度仿真到真实迁移的力控制研究[J]. 机械工程学报, 2021, 57(17): 53-63.
[2]	曹秒艳, 胡晗, 田少杰, 杜冰, 赵长财. 抛物线壳体软模成形FEM-DEM耦合仿真研究[J]. 机械工程学报, 2020, 56(20): 38-46.
[3]	汪通悦;何宁;李亮. 薄壁零件铣削加工的振动模型[J]. , 2007, 43(8): 22-25.