近距离淹没冲击射流动态流场特性

doi:10.3901/JME.2020.22.263

机械工程学报 ›› 2020, Vol. 56 ›› Issue (22): 263-270.doi: 10.3901/JME.2020.22.263

扫码分享

近距离淹没冲击射流动态流场特性

胡建军^1,2, 杨子文¹, 金瑶兰³, 王思民³, 孔祥东²

1. 燕山大学河北省土木工程绿色建造与智能运维重点实验室秦皇岛 066004;
2. 燕山大学机械工程学院秦皇岛 066004;
3. 上海衡拓液压控制技术有限公司上海 201612

收稿日期:2020-01-13 修回日期:2020-05-27 出版日期:2020-11-20 发布日期:2020-12-31
通讯作者: 胡建军(通信作者),男,1982年出生,博士,副教授,博士研究生导师。主要研究方向为液压流体力学。E-mail:kewei729@163.com
作者简介:杨子文,男,1995年出生。主要研究方向为流体力学。E-mail:cq.yangziwen@qq.com
基金资助:
国家自然科学基金资助项目（51705446，51890881）。

Dynamic Flow-field Characteristics of Close-range Submerged Impinging Jet

HU Jianjun^1,2, YANG Ziwen¹, JIN Yaolan³, WANG Simin³, KONG Xiangdong²

1. Key Laboratory of Green Construction and Intelligent Maintenance for Civil Engineering of Hebei Province, Yanshan University, Qinhuangdao 066004;
2. School of Mechanical Engineering, Yanshan University, Qinhuangdao 066004;
3. Shanghai Hunter Hydraulic Control Technology Co., Ltd., Shanghai 201612

Received:2020-01-13 Revised:2020-05-27 Online:2020-11-20 Published:2020-12-31

摘要/Abstract

摘要： 近距离下淹没冲击射流具有重要的应用前景，但有关其动态流场特性的研究尚不充分。利用粒子图像测速技术（Particle image velocimetry，PIV）对冲击距离为H/D=1时的动态流场特性进行测量，研究雷诺数Re和喷嘴端面轮廓（壁面约束）对间隙内旋涡生成的影响，并对试验数据进行涡量分析与本征正交分解方法（Proper orthogonal decomposition，POD）分析。结果表明，雷诺数Re对不同喷嘴端面轮廓（壁面约束）的旋涡生成和迁移影响规律不同。雷诺数对直角型喷嘴的双涡环模式流态影响较小，但对圆角型喷嘴卷吸流态影响较大，且随雷诺数的增大流场出现动态对称涡旋，该对称涡旋逐渐向间隙外迁移且呈现出明显的周期性变化特征。涡量分析得到时均场的涡量大小与分布情况，通过与POD分析中瞬态场的含能大尺度结构分布相结合，揭示间隙外涡旋能量的来源与变化规律。通过前4阶瞬态脉动速度场重构，可以从微观时间尺度进一步说明瞬态速度场的突变性与周期性。研究成果将有助于加深对冲击射流本质的理解。

关键词: 冲击射流, 淹没, PIV, 近距离, 动态流场

Abstract: Submerged impact jet at close range has important application in many fields,but the research on the dynamic flow-field characteristics is not yet sufficient. Particle image velocimetry(PIV) is used to measure the dynamic flow-field characteristics of impinging jet when the impact distance is H/D=1. The effects of Reynolds number Re and the nozzle end-profile (wall constraints) on the vortex generation and migration inside and outside the gap are studied. The experimental data are analyzed by vorticity analysis and proper orthogonal decomposition(POD) method. The results show that the Reynolds number has different effects on the vortex generation and migration of different nozzle end profile (wall constraint). The Reynolds number has little effect on the flow pattern of the double vortex ring mode of the right-angle nozzle,but has a greater influence on the flow pattern of the round angle nozzle,and the dynamic symmetric vortex appears with the increase of the Reynolds number. The symmetrical vortex gradually migrated out of the gap and exhibited obvious periodic variation characteristics. The vorticity analysis obtains the vorticity size and distribution of the time-averaged field. By combining with the distribution of the energetic large-scale structure of the transient field in the POD analysis,the source and variation of the vortex energy outside the gap are revealed. By the reconstruction of the first four orders transient pulsating velocity field,the abrupt change and periodicity of the transient velocity field can be further explained based on the microscopic time scale. This result is helpful to deepen the understanding of impingement jets.

Key words: impingement jet, submerged, PIV, close-range impingement, dynamic flow-field

中图分类号:

TB126

胡建军, 杨子文, 金瑶兰, 王思民, 孔祥东. 近距离淹没冲击射流动态流场特性[J]. 机械工程学报, 2020, 56(22): 263-270.

HU Jianjun, YANG Ziwen, JIN Yaolan, WANG Simin, KONG Xiangdong. Dynamic Flow-field Characteristics of Close-range Submerged Impinging Jet[J]. Journal of Mechanical Engineering, 2020, 56(22): 263-270.

参考文献

[1] SABATO M,FREGNI A,STALIO E,et al. Numerical study of submerged impinging jets for power electronics cooling[J]. International Journal of Heat and Mass Transfer,2019,141:707-718.
[2] RAIZNER M,RINSKY V,GROSSMAN G,et al. The effect of jet pulsation on the flow field of a round impinging jet and the radially expanding wall jet[J]. International Journal of Heat and Mass Transfer,2019,140:606-619.
[3] CALISKAN S,BASKAYA S,CALISIR T. Experimental and numerical investigation of geometry effects on multiple impinging air jets[J]. International Journal of Heat and Mass Transfer,2014,75:685-703.
[4] 马鹏程,唐志国,刘轻轻,等. 新型单圆锥体热沉单孔射流散热数值模拟[J]. 机械工程学报,2016,52(24):136-141. MA Pengcheng,TANG Zhiguo,LIU Qingqing,et al. Numerical simulation of characteristic of heat transfer for jet impingement with new single cone heat sink through single spray nozzle[J]. Journal of Mechanical Engineering,2016,52(24):136-141.
[5] CHANG S W,SHEN H D. Heat transfer of impinging jet array with web-patterned grooves on nozzle plate[J]. International Journal of Heat and Mass Transfer,2019,141:129-144.
[6] 谢军龙,张祎,郭宝坤,等. 射流冲击圆锥噪声特性试验及数值分析[J]. 工程热物理学报,2016,37(6):1212-1217. XIE Junlong,ZHANG Yi,GUO Baokun,et al. Experimental and numerical analysis of jet impact cone noise characteristics[J]. Journal of Engineering Thermophysics,2016,37(6):1212-1217.
[7] LI Y M,LI B K,QI F S,et al. Flow and heat transfer of parallel multiple jets obliquely impinging on a flat surface[J]. Applied Thermal Engineering,2018,133:588-603.
[8] LI S Y,ZHANG Y Y,XU B. Correlation analysis of superheated liquid jet breakup to bubble formation in a transparent slit nozzle[J]. Experimental Thermal and Fluid Science,2015,68:452-458.
[9] 焦磊,王乐勤,徐如良,等. 冲击高度对淹没冲击射流影响的数值预测[J]. 工程热物理学报,2005(5):773-775. JIAO Lei,WANG Leqin,XU Ruliang,et al. Numerical prediction of influence of impact height on submerged impact jet[J]. Journal of Engineering Thermophysics,2005(5):773-775.
[10] ROGER E K. Impinging planar jet flow on a horizontal surface with slip[J]. Journal of Fluid Mechanics,2016,808:258-289.
[11] WANG Y P,ROGER E K. Impinging jet flow and hydraulic jump on a rotating disk[J]. Journal of Fluid Mechanics,2018,839:525-560.
[12] WILKE R,JORN S. Statistics of fully turbulent impinging jets[J]. Journal of Fluid Mechanics,2017,825:795-824.
[13] DAIRAY T,FORTUNE V,LAMBALLAIS E,et al. Direct numerical simulation of a turbulent jet impinging on a heated wall[J]. Journal of Fluid Mechanics,2015,764:362-394.
[14] XU Y,WANG J J,FENG L H,et al. Laminar vortex rings impinging onto porous walls with a constant porosity[J]. Journal of Fluid Mechanics,2018,837:729-764.
[15] GRECO C S,CARDONE G,SORIA J. On the behavier of impinging zero-net-mass-flux jets[J]. Journal of Fluid Mechanics,2017,810:25-59.
[16] ASSELIN D J,WILLIAMSON C H K. Influence of a wall on the three-dimensional dynamics of a vortex pair[J]. Journal of Fluid Mechanics,2017,817:339-373.
[17] 刘璐璐,翟树成,张国平,等. 平板湍流边界层流向-法向平面发卡涡的PIV试验研究[J]. 船舶力学,2016,20(Z1):23-30. LIU Lulu,ZHAI Shucheng,ZHANG Guoping,et al. PIV experimental study on the flow direction of the flat turbulent boundary layer and the normal plane hairpin vortex[J]. Journal of Ship Mechanics,2016,20(Z1):23-30.
[18] VITO P,HICKEL S,NIKOLAUS A A. Unsteady efects of strong shock-wave/boundary-layer interaction at high Reynolds number[J]. Journal of Fluid Mechanics,2017,823:617-657.
[19] 肖毅,熊良才. 无针注射射流穿透表皮机理理论研究[J]. 机械与电子,2012(4):12-14. XIAO Yi,XIONG Liangcai. Theoretical study on the mechanism of needle-free injection jet penetrating the epidermis[J]. Machinery and Electronics,2012(4):12-14.
[20] 李登,李晓红,康勇,等. 风琴管喷嘴内表面粗糙度对高压射流特性的影响试验研究[J]. 机械工程学报,2015,51(17):169-176. LI Deng,LI Xiaohong,KANG Yong,et al. Experimental investigation on the influence of internal surface roughness of organ pipe nozzle on the characteristics of high pressure jet[J]. Journal of Mechanical Engineering,2015,51(17):169-176.
[21] WANG S Q,AHMAD B,LUCIEN B,et al. On the modelling of the switching mechanisms of a Coanda fluidic oscillator[J]. Sensors and Actuators:A. Physical,2019,299:111618.
[22] 朱玉川,李跃松. 射流伺服阀用放大型超磁致伸缩执行器建模及分析[J]. 航空学报,2014,35(11):3156-3165. ZHU Yuchuan,LI Yuesong. Modeling and analysis of enlarged giant magnetostrictive actuator for jet servo valve[J]. Acta Aeronautica,2014,35(11):3156-3165.
[23] LUMLEY J L,HOLMES P,BERKOOZ G. The proper orthogonal de-composition in the analysis of turbulent flows[J]. Ann. Rev. Fluid Mech.,1993,25:539-575.

近距离淹没冲击射流动态流场特性

Dynamic Flow-field Characteristics of Close-range Submerged Impinging Jet

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	方玉建, 张敏, 孙先朋, 张金凤, 瞿晔飞. 机械搅拌槽内非牛顿流体内流特性研究[J]. 机械工程学报, 2021, 57(20): 244-253.
[2]	张晋, 龚学知, 胡建军, 权凌霄, 哈良, 孔祥东. 轴向柱塞泵配流分析用湍流模型探析[J]. 机械工程学报, 2018, 54(18): 204-211.
[3]	马鹏程, 唐志国, 刘轻轻, 王元哲. 新型单圆锥体热沉单孔射流散热数值模拟^*[J]. 机械工程学报, 2016, 52(24): 136-141.
[4]	龚曙光，何峰，刘克俭，隆香花. 高速空气射流冲击颗粒物料层的参数特性[J]. 机械工程学报, 2015, 51(15): 142-147.
[5]	刘栋;朱鹣;朱方能;杨晓勇;金亨凡. 沟槽数量对泰勒涡流稳定性的影响[J]. , 2014, 50(22): 186-191.
[6]	周静伟;杨兴贤;耿丽萍;王玉刚. 非稳态冲击射流强化传热试验研究[J]. , 2010, 46(6): 144-148.
[7]	谢海波;傅新;杨华勇;陈虹. 典型微管道流场数值模拟与Micro-PIV检测研究[J]. , 2006, 42(5): 32-38.
[8]	袁寿其;何有世;袁建平;丛小青;赵斌娟. 带分流叶片的离心泵叶轮内部流场的PIV测量与数值模拟[J]. , 2006, 42(5): 60-63.
[9]	陈庆光;吴玉林;刘树红;张永超;张永建. 三维方管层流冲击射流流动与传热的数值研究[J]. , 2006, 42(1): 206-211.
[10]	谢海波;傅新;杨华勇. 基于Micro-PIV的微观流场检测技术[J]. , 2005, 41(9): 106-111.
[11]	万毅;柯坚. 离心泵流道和泵腔内流场的试验研究[J]. , 2005, 41(10): 226-230.
[12]	宫武旗;吕伟领;席光;张伟. 前向多翼式离心风机蜗舌附近流场的PIV试验研究[J]. , 2005, 41(1): 166-171.
[13]	高殿荣;王益群;Acharya Sumanta. Rushton桨搅拌槽内平均流场的二维PIV试验研究[J]. , 2004, 40(12): 192-198.
[14]	高殿荣;王益群;杨林杰;侯桂庆. 绕后台阶与准方腔耦合流道流场的数值计算与试验研究[J]. , 2004, 40(10): 48-55.
[15]	张玮;王元;徐忠. 粒子图像速度场仪用于叶轮机械内流测量的研究[J]. , 2002, 38(7): 17-22.