碳纳米管对大粒度多层钎焊金刚石砂轮电解修整磨削性能的影响研究

doi:10.3901/JME.2020.07.231

机械工程学报 ›› 2020, Vol. 56 ›› Issue (7): 231-239.doi: 10.3901/JME.2020.07.231

扫码分享

碳纳米管对大粒度多层钎焊金刚石砂轮电解修整磨削性能的影响研究

伍俏平^1,2, 欧阳志勇², 阳慧², 宋琨², 邓朝晖^1,2

1. 难加工材料高效精密加工湖南省重点实验室湘潭 411201;
2. 湖南科技大学智能制造研究院湘潭 411201

收稿日期:2019-07-11 修回日期:2019-12-09 出版日期:2020-04-05 发布日期:2020-05-12
作者简介:伍俏平(通信作者),男,1981年出生,博士,教授,博士研究生导师。主要研究方向为新型工具制备及难加工材料高效精密加工技术。E-mail:meishanzi11@sina.com
基金资助:
国家自然科学基金（51575179，51205126），湖南省自然科学基金（2017JJ3073，12JJB006）和湖南省教育厅重点项目（18A182）资助项目。

Influence of Carbon Nanotubes on Electrolytic Dressing Grinding Performance of a Multi-layer Brazed Coarse-grained Diamond Wheel

WU Qiaoping^1,2, OUYANG Zhiyong², YANG Hui², SONG Kun², DENG Zhaohui^1,2

1. Hunan Province Key Laboratory of High Efficiency and Precision Machining of Difficult to Machine Materials, Xiangtan 411201;
2. Institute of Intelligent Manufacturing, Hunan University of Science and Technology, Xiangtan 411201

Received:2019-07-11 Revised:2019-12-09 Online:2020-04-05 Published:2020-05-12

摘要/Abstract

摘要： 制备了一种含碳纳米管电解液以用于大粒度多层钎焊金刚石砂轮的电解修整，并分析了碳纳米管对电解氧化膜特性及电解修整磨削性能的影响。研究结果表明碳纳米管能显著提高电解液的电解能力，电解氧化膜厚度增大了56.3%～80.2%，这有利于磨损磨粒的顺利脱落；螺旋卷曲状的碳纳米管在电解过程中能吸附、分布于氧化膜中，氧化膜的粘附强度增大了30%～50%，这能充分发挥氧化膜的研磨、抛光效果。含碳纳米管电解液电解修整大粒度多层钎焊金刚石砂轮磨削力比普通电解液电解修整磨削力降低了30%以上；磨削表面粗糙度小，且增长幅度相对平缓，即使当进给速度为30 mm/s，磨削深度为16 μm时，表面粗糙度也仅为0.15 μm左右；含碳纳米管电解液电解修整大粒度多层钎焊金刚石砂轮磨削加工表面完整性较好，没有出现破碎、裂纹等加工缺陷，可有效实现超细晶硬质合金等难加工材料的高效精密磨削加工。

关键词: 碳纳米管, 大粒度多层钎焊金刚石砂轮, 电解修整, 超细晶硬质合金, 氧化膜, 磨削性能

Abstract: An electrolyte containing carbon nanotubes (CNTs) is prepared for electrolytic dressing of a multi-layer brazed coarse-grained diamond grinding wheel, and the influence of CNTs on the characteristics of oxide film and the electrolytic dressing grinding performance are investigated. The results indicated that CNTs could significantly improve the electrolytic capacity of electrolyte, and the thickness of oxide film increased by 56.3% to 80.2%, which allowed the worn diamond grits to fall off smoothly. CNTs are adsorbed and distributed in the oxide film during electrolytic dressing, and the adhesion strength of the oxide film increases by 30%-50%, which could improve the polishing effect of the oxide film. The grinding experiment results shows that the grinding force of the multi-layer brazed coarse-grained diamond wheel after electrolytic dressing with electrolyte containing CNTs decreased by 30%. The grinding surface roughness is small and the increase rate is relatively gentle. When the feed speed is 30 mm/s and the grinding depth is 16 μm, the surface roughness is just about 0.15 μm. Moreover, the integrity of surface ground by the brazed wheel after electrolytic dressing with electrolyte containing CNTs is good, there are no cracks and other defects. It could effectively realize the high efficiency and precise grinding of ultra-fine cemented carbide and other difficult-to-cut materials.

Key words: carbon nanotubes, multi-layer brazed coarse-grained diamond wheel, electrolytic dressing, ultra-fine cemented carbide, oxide film, grinding performance

中图分类号:

TG521

伍俏平, 欧阳志勇, 阳慧, 宋琨, 邓朝晖. 碳纳米管对大粒度多层钎焊金刚石砂轮电解修整磨削性能的影响研究[J]. 机械工程学报, 2020, 56(7): 231-239.

WU Qiaoping, OUYANG Zhiyong, YANG Hui, SONG Kun, DENG Zhaohui. Influence of Carbon Nanotubes on Electrolytic Dressing Grinding Performance of a Multi-layer Brazed Coarse-grained Diamond Wheel[J]. Journal of Mechanical Engineering, 2020, 56(7): 231-239.

参考文献

[1] 伍俏平,邓朝晖,潘占,等.金刚石纤维砂轮的制备及磨削表面质量研究[J].机械工程学报,2014,50(11):205-212. WU Qiaoping,DENG Zhaohui,PAN Zhan,et al. Preparation and grinding surface-quality of a new diamond fiber wheel[J]. Journal of Mechanical Engineering,2014,50(11):205-212.
[2] XIAO H Z,XIAO B,WU H H. Interfacial characteristics and mechanical properties of the vacuum brazing diamond grains segment with Ni-Cr composite active filler and tungsten carbide reinforcement[J]. Journal of Alloys and Compounds,2019,781:226-234.
[3] WU Q P,LUO Z,WANG Y,et al. Effects of rare earth Ce on the brazing performance of high energy mechanical milling Cu-based alloy powder[J]. Metals,2018,495,8:1-12.
[4] DING W F,ZHU Y J,ZHANG L Z,et al. Stress characteristics and fracture wear of brazed CBN grains in monolayer grinding wheel[J]. Wear,2015,332:800-809.
[5] CHATTOPADHYAY A K,CHOLLET L,HINTERMANN H E. On the performance of brazed bonded monolayer diamond grinding wheel[J]. CIRP Annals,1991,40(1):347-350.
[6] LU J B,CAO Z Y,QI F J,et al. Evolution of interface carbide diamond brazed with filler alloy containing Cr[J]. Diamond & Related Materials,2018,90:116-125.
[7] CHEN J Y,HUANG H,XU X P. An experimental study on the grinding of Alumina with a monolayer brazed diamond wheel[J]. International Journal of Advanced Manufacturing Technology,2009,41:16-23.
[8] 徐正亚,徐鸿钧,傅玉灿.钎焊金刚石砂轮磨削硬质合金温度的试验研究[J].金刚石与磨料磨具工程,2010,30(6):65-69. XU Zhengya,XU Hongjun,FU Yucan. Experimental study on grinding temperature of cemented carbide with brazed diamond grinding wheel[J]. Diamond & Abrasives Engineering,2010,30(6):65-69.
[9] 伍俏平,王煜,赵恒,等.基于多层钎焊金刚石砂轮在线电解修整技术的超细晶硬质合金精密磨削研究[J].机械工程学报,2018,54(21):212-220. WU Qiaoping,WANG Yu,ZHAO Heng,et al. Precision grinding of ultra-fine cemented carbide based on electrolytic in-process dressing of a multi-layer brazed diamond wheel[J]. Journal of Mechanical Engineering,2018,54(21):212-220.
[10] HAN T,NAG A,MUKHOPADHYAY S C. Carbon nanotubes and its gas-sensing applications:A review[J]. Sensors and Actuators A,2019,291:107-143.[11 FIYADH S S,ALSAADI M A,JAAFAR W Z,et al. Review on heavy metal adsorption processes by carbon nanotubes[J]. Journal of Cleaner Production,2019,23:783-793.
[12] 伍俏平,王煜,瞿为,等.在线电解修整磨削液研究现状及其展望[J].中国机械工程,2017,28(9):1118-1124. WU Qiaoping,WANG Yu,QU Wei,et al. Research status and perspectives of ELID grinding fluid[J]. China Mechanical Engineering,2017,28(9):1118-1124.
[13] LIU W D,ZHANG H,LUO Z,et al. Electrochemical micromachining on titanium using the NaCl-containing ethylene glycol electrolyte[J]. Journal of Materials Processing Technology,2018,255:784-794.
[14] HE Y F,XIAO H X,GAN W M,et al. The electrochemical dissolution behavior research of titanium alloy under different electrolyte[J]. Procedia CIRP,2018,68:751-756.
[15] 杨永珍.碳微球表面化学[M].北京:化学工业出版社,2012. YONG Yongzhen. Surface chemistry of carbon micro-beads[M]. Beijing:Chemical Industry Press,2012.
[16] DATSUKV,KALYVA M,PAPAGELISK,et al. Chemical oxidation of multiwalled carbon nanotubes[J]. Carbon,2008,46:833-840.
[17] CHO J,KONOPKA K,ROZNIATOWSKI K,et al. Characterization of carbon nanotube films deposited by electrophoretic deposition[J]. Carbon,2009,47:58-67.
[18] 伍俏平,郑维佳,邓朝晖,等.在线电解修整氧化膜研究现状及展望[J].中国机械工程,2018,29(17):2023-2030. WU Qiaoping,ZHENG Weijia,DENG Zhaohui,et al. Research status and perspectives of ELID grinding oxidation films[J]. China Mechanical Engineering,2017,2018,29(17):2023-2030.

[1]	武韩强, 陈卓, 叶曦珉, 张诗博, 李偲偲, 曾江, 汪强, 吴勇波. 钛合金超声辅助等离子体氧化改性磨削基本加工特性研究[J]. 机械工程学报, 2024, 60(9): 13-25.
[2]	关集俱, 祝正兵, 徐正亚, 栾志强, 许雪峰. CNTs@T321微囊制备的纳米流体与砂轮磨削时的双重润滑增效机制[J]. 机械工程学报, 2024, 60(9): 351-363.
[3]	常青, 张丽霞, 孙湛, 宋义河, 朱泳安. 表面生长碳纳米管对C/C复合材料钎焊接头的影响[J]. 机械工程学报, 2020, 56(8): 20-27.
[4]	刘庆冬, 张浩, 曾奇锋, 卢俊强, 李聪, 张乐福. SZA-4和ZIRLO锆合金在360℃含氧水环境中的腐蚀行为[J]. 机械工程学报, 2019, 55(8): 88-96.
[5]	高英山, 张顺琦, 黄钟童. CNT纤维增强功能梯度复合板非线性建模与仿真[J]. 机械工程学报, 2019, 55(8): 80-87.
[6]	薛婷, 秦现生, 张顺琦, 王战玺, 白晶. 基于一阶剪切变形理论的CNTRC板的自由振动分析[J]. 机械工程学报, 2019, 55(24): 45-50.
[7]	彭锐涛, 刘开发, 黄晓芳, 降皓鉴, 张珊. 流道结构对加压内冷却开槽砂轮磨削性能的影响[J]. 机械工程学报, 2019, 55(13): 212-223.
[8]	伍俏平, 王煜, 赵恒, 郑维佳, 邓朝晖. 基于多层钎焊金刚石砂轮在线电解修整技术的超细晶硬质合金精密磨削研究[J]. 机械工程学报, 2018, 54(21): 212-220.
[9]	薛婷, 秦现生, 张顺琦, 李鹏程, 张书扬. 碳纳米管增强功能梯度复合材料薄板建模与分析[J]. 机械工程学报, 2018, 54(16): 93-100.
[10]	吕涛, 黄水泉, 易芳, 万家傲, 许雪峰. 液体润滑剂/β-环糊精包合物为填料的酚醛树脂砂轮自润滑性能研究[J]. 机械工程学报, 2017, 53(17): 160-171.
[11]	崔照雯;李敬仁;李泽洲;曾石轩;颜翃;蒋立坤;贾成厂. 粉末冶金法CNTs、Al2O3双增强铜基复合材料性能研究[J]. , 2013, 49(18): 52-56.
[12]	唐一科;郑富中;周兆英;杨兴;吴英. 基于单壁碳纳米管阵列的力敏传感器[J]. , 2010, 46(18): 13-17.
[13]	胡方海;王三民;刘海霞. 双壁碳纳米管转动阻尼特性和承载能力的计算分析[J]. , 2009, 45(7): 312-316.
[14]	徐屹;凤仪;王松林;张学斌;沈剑. 碳纳米管－银－石墨复合材料的电磨损性能[J]. , 2006, 42(12): 206-210.
[15]	褚巍;赵学增;Joseph Fu;Theodore V. Vorburger. 纳米尺度表面形貌测量的双图像拼接法[J]. , 2005, 41(9): 166-170.

碳纳米管对大粒度多层钎焊金刚石砂轮电解修整磨削性能的影响研究

Influence of Carbon Nanotubes on Electrolytic Dressing Grinding Performance of a Multi-layer Brazed Coarse-grained Diamond Wheel

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价