磨料粒度对表面微织构纯钛干摩擦性能的影响

doi:10.3901/JME.2017.24.025

机械工程学报 ›› 2017, Vol. 53 ›› Issue (24): 25-33.doi: 10.3901/JME.2017.24.025

• 特邀专栏：表面工程先进技术及其服役行为（上） • 上一篇下一篇

磨料粒度对表面微织构纯钛干摩擦性能的影响

李星亮^1,2, 岳文^1,3, 黄飞¹, 康嘉杰^1,3, 付志强^1,3

1. 中国地质大学(北京)工程技术学院北京 100083;
2. 中国航空工业集团公司北京航空精密机械研究所精密制造技术航空科技重点实验室北京 100076;
3. 中国地质大学(北京)深部地质钻探技术国土资源部重点实验室北京 100083

收稿日期:2017-05-10 修回日期:2017-08-28 发布日期:2017-12-20
通讯作者: 岳文(通信作者),男,1981年出生,博士,教授,博士研究生导师。主要研究方向为机械摩擦学与表面技术、勘探技术与地质钻探学、金刚石及其他超硬材料。E-mail:yw@cugb.edu.cn
作者简介:李星亮,男,1987年出生,博士研究生,工程师。主要研究方向为摩擦学与表面工程,机械设计及理论。E-mail:lixing3758@126.com
基金资助:
国家自然科学基金（41572362，U1537108）、北京市自然科学基金（3172026）、中央高校基本科研业务费（2652015077）、装备预研中航工业联合基金（6141B05090401）和“十三五”装备预研共用技术（41423020304）资助项目。

Effect of Wear Particle Size on Dry Tribological Properties of Surface Texturing Titanium

LI Xingliang^1,2, YUE Wen^1,3, HUANG Fei¹, KANG Jiajie^1,3, FU Zhiqiang^1,3

1. School of Engineering and Technology, China University of Geosciences(Beijing), Beijing 100083;
2. Aviation Key Laboratory of Science and Technology on Precision Manufacturing, Beijing Precision Engineering Institute for Aircraft Industry, Aviation Industry Corporation of China, Beijing 100076;
3. Key Laboratory on Deep GeoDrilling Technology, Ministry of Land and Resources, China University of Geosciences(Beijing), Beijing 100083

Received:2017-05-10 Revised:2017-08-28 Published:2017-12-20

摘要/Abstract

摘要： 为了提高钛及钛合金钻具在超深钻探、深海钻探和外太空钻探工程中的减摩抗磨性能。利用激光表面加工技术在工业纯钛（TA2）表面制备了不同参数的点阵微织构。采用MS-T3000摩擦磨损试验机测试了微织构钛合金在不同粒度模拟月壤作用下的摩擦学性能。利用扫描电子显微镜和能谱分析仪分析磨痕形貌及元素含量。研究结果表明：当磨料粒度小于微织构点阵的直径时，磨料压入微织构点阵里，磨料具有滚动和滑动两种运动方式。当粒度大于微织构点阵的直径时，磨料不能完全压入微织构点阵里，磨料对微织构TA2表面产生了滑动犁削作用。由于两种磨料磨损的作用机理不同，同等条件下，小粒度的磨料作用下的微织构TA2的摩擦因数和磨损率较大粒度磨粒作用下的最大减少量分别为50%和53%。考虑磨料粒度与微结构的匹配性，可以大大降低摩擦减少磨损。

关键词: 激光表面微织构, 摩擦学性能, 磨料粒度, 磨料磨损, 钛合金

Abstract: In order to improve anti-friction and anti-wear performance of the titanium alloy drilling tools used in the ultra deep drilling, deep sea drilling, and drilling engineering in outer space. Dimple textures are prepared on TA2 titanium surface by means of laser surface texturing (LST). Tribological behaviors of the texturing surfaces are investigated under lubrication with two kinds of simulated lunar soil in dry sliding contact on a MS-T3000 friction and wear tester. The micro-morphologies and element content on the worn surfaces are analyzed by scanning electron microscopy (SEM) and energy dispersive spectrometer (EDS), respectively. The result shows that the wear particle would be compressed to completely embed into the dimples while lubricated by small particles. The small wear particles combine with rolling and sliding movements in the process of sliding which lead to lower friction and wear on the texturing TA2 surface. However, unavoidable sliding damages take place the texturing surface lubricated by large particles. The large foreign particles are too difficult to be squeezed to embed completely into the dimples results in larger friction coefficients and wear rate on the texturing TA2 surface. So, the highest reduction ratios for friction coefficient and wear rate are 50% and 53% for the texturing surface which is lubricated by small particles comparing with it lubricated by large particles. Besides, the matching rate of abrasive particle size and texture parameter can greatly reduce friction and wear.

Key words: abrasive wear, laser surface texturing, titanium alloy, tribological property, wear particle size

中图分类号:

TH117

李星亮, 岳文, 黄飞, 康嘉杰, 付志强. 磨料粒度对表面微织构纯钛干摩擦性能的影响[J]. 机械工程学报, 2017, 53(24): 25-33.

LI Xingliang, YUE Wen, HUANG Fei, KANG Jiajie, FU Zhiqiang. Effect of Wear Particle Size on Dry Tribological Properties of Surface Texturing Titanium[J]. Journal of Mechanical Engineering, 2017, 53(24): 25-33.

参考文献

[1] 温诗铸. 我国摩擦学研究的现状与发展[J]. 机械工程学报,2004,40(11):1-6. WEN Shizhu. The present situation and development of tribological research in China[J]. Chinese Journal of Mechanical Engineering,2004,40(11):1-6.
[2] 温诗铸. 纳米摩擦学研究进展[J]. 机械工程学报,2007,43(10):1-8. WEN Shizhu. Research progress of nano tribology[J]. Chinese Journal of Mechanical Engineering,2007,43(10):1-8.
[3] BANERJEE D,WILLIAMS J C. Perspectives on titanium science and technology[J]. Acta Materialia,2013,61:844-879.
[4] LEYENS C,PETERS M. Titanium and titanium alloys:Fundamentals and applications[J]. Weinheim:Wiley-VCH,2003.
[5] LUTJERING G,WILLIAMS J C. Titanium[M]. 2nd ed. Berlin:Springer,2007.
[6] BUDINSKI K G. Tribological properties of titanium alloys[J]. Wear,1991,151:203-217.
[7] GUO L T,LIU X C,GAO J Q,et al. Effect of surface modifications to Tiporcelain bonding strength[J]. Materials and Manufactruing Processes,2010,25:710-717.
[8] DONG Z H,FANG G Y,JI Y C,et al. Parameters and structure of lunar regolith in Chang'E-3 landing area from lunar penetrating radar (LPR) data[J]. Icarus,2017,282:40-46.
[9] 张森森,王世杰,李雄耀,等. 月尘的性质及危害评述[J]. 地球科学-中国地质大学学报,2013,38(2):339-350. ZHANG Sensen,WANG Shijie,LI Xiongyao,et al. Properties and harmfulness of lunar dust:A review[J]. Earth Science-Journal of China University of Geosciences,2013,38(2):339-350.
[10] 白羽,郝宁,王志浩,等. 模拟月尘对巡视器车轮轮轴材料的磨损试验研究[J]. 航天器环境工程,2013,30(5):493-498. BAI Yu,HAO Ning,WANG Zhihao,et al. Abrasion test on wheel and axle materials of lunar rover under the influence of simulation lunar dust[J]. Spacecraft Environment Engineering,2013,30(5):493-498.
[11] GROPPER D,WANG L,HARVEY T J. Hydrodynamic lubrication of textured surfaces:A review of modeling techniques and key findings[J]. Tribology International,2016,94:509-529.
[12] WU Shaofeng,GAO Dianrong,LIANG Yingna,et al. Influence of non-smooth surface on tribological properties of glass fiber-epoxy resin composite sliding against stainless steel under natural seawater lubrication[J]. Chinese Journal of Mechanical Engineering,2015,28(6):1171-1176.
[13] SHINKARENKO A,KLIGERMAN Y,ETSION I. The effect of surface texturing in soft elasto-hydrodynamic lubrication[J]. Tribology International,2009,42:284-292.
[14] ETSION I,KLIGERMAN Y,HALPERIN G. Analytical and experimental investigation of laser-textured mechanical seal faces[J]. Tribology Transactions,1999,42(3):511-516.
[15] COSTA H L,HUTCHINGS I M. Hydrodynamic lubrication of textured steel surfaces under reciprocating sliding conditions[J]. Tribology International,2007,40:1227-1238.
[16] IBATAN T,UDDIN M S,CHOWDHURY M A K.. Recent development on surface texturing in enhancing tribological performance of bearing sliders[J]. Surface & Coatings Technology,2015,272:102-120.
[17] DASILVA W M,SUAREZ M P,MACHADO A R,et al. Effect of laser surface modification on the micro-abrasive wear resistance of coated cemented carbide tools[J]. Wear,2013,302:1230-1240.
[18] LIU Y Y,DENG J X,Wu F F,et al. Wear resistance of carbide tools with textured flank-face in dry cutting of green alumina ceramics[J]. Wear,2017,372-373:91-103.
[19] LI K M,YAO Z Q,HU Y X,et al. Friction and wear performance of laser peen textured surface under starved lubrication[J]. Tribology International,2014,77:97-105.
[20] WU Z,XING Y Q,HUANG P,et al. Tribological properties of dimple-textured titanium alloys under dry sliding contact[J]. Surface & Coatings Technology,2017,309:21-28.
[21] JANSSEN A,PINEDO B,IGARTUA A,et al. Study on friction and wear reducing surface micro-structures for a positive displacement pump handling highly abrasive shale oil[J]. Tribology International,2017,107:1-9.
[22] AMANOV A,SASAKI S. A study on the tribological characteristics of duplex-treated Ti-6Al-4V alloy under oil-lubricated sliding conditions[J]. Tribology International,2013,64:155-163.
[23] HE D Q,ZHENG S X,PU J B,et al. Improving tribological properties of titanium alloys by combining laser surface texturing and diamond-like carbon film[J]. Tribology International,2015,82:20-27.
[24] BUSCAGLIA G C,CIUPERCA I,JAI M. On the optimization of surface textures for lubricated contacts[J]. Journal of Mathematical Analysis and Applications. 2007,335:1309-1327.
[25] COSTA H L,HUTCHINGS I M. Hydrodynamic lubrication of textured steel surfaces under reciprocating sliding conditions[J]. Tribology International,2007,40:1227-1238.
[26] WANG X L,KATO K,ADACHI K,et al. Loads carrying capacity map for the surface texture design of SiC thrust bearing sliding in water[J]. Tribology International,2003,36:189-197.
[27] GAO L M,YANG P R,DYMOND I,et al. Effect of surface texturing on the elastohydrodynamic lubrication analysis of metal-on-metal hip implants[J]. Tribology International,2010,43:1851-1860.
[28] BRUNETI ERE N,TOURNERIE B. Numerical analysis of a surface-textured mechanical seal operating in mixed lubrication regime[J]. Tribology International,2012,49:80-89.
[29] KIM B,CHAE Y H,CHOI H S. Effects of surface texturing on the frictional behavior of cast iron surfaces[J]. Tribology International,2014,70:128-135.
[30] 于如飞,陈渭. 表面织构化在工业摩擦学领域的研究现状与展望[J]. 机械工程学报,2017,53(3):100-110. YU Rufei,CHEN Wei. Research progress and prospect of surface texturing in industrial tribology[J]. Journal of Mechanical Engineering,2017,53(3):100-110.
[31] 周仲荣,钱林茂. 摩擦学尺寸效应及相关问题的思考[J]. 机械工程学报,2003,39(8):22-26. ZHOU Zhongrong,QIAN Linmao. Tribological size effect and related problems[J]. Journal of Mechanical Engineering,2003,39(8):22-26.
[32] 朱华,陆斌斌,历建全,等. 摩擦学问题研究的非线性理论方法[J]. 机械工程学报,2010,46(15):82-88. ZHU Hua,LU Binbin,LI Jianquan,et al. Nonlinear theory and methods of researching tribological problems[J]. Journal of Mechanical Engineering,2010,46(15):82-88.
[33] ZHANG H,ZHANG D Y,HUA M,et al. A study on the tribological behavior of surface texturing on babbitt alloy under mixed or starved lubrication[J]. Tribology Letter,2014,56:305-315.
[34] FANG L,KONG X L,ZHOU Q D. A wear tester capable of monitoring and evaluating the movement pattern of abrasive particles in three-body abrasion[J]. Wear,1992,159:115-120.
[35] FANG L,KONG X L,SU J Y,et al. Movement patterns of abrasive particles in three-body abrasion[J]. Wear,1993,162-164:782-789.
[36] 桑多尔B I. 循环应力和循环应变的基本原理[M]. 北京:科学出版社,1985. SANDOR B I. The basic principle of cyclic stress and cyclic strain[M]. Beijing:Science Press,1985.
[37] 温诗铸. 摩擦学原理[M]. 北京:清华大学出版社,1990. WEN Shizhu. Principles of tribology[M]. Beijing:Tsinghua University Press,1990.
[38] JOHNSON K L. Contact mechanics[M]. Cambridge:Cambridge University Press,1985.
[39] 常秋英,齐烨,王斌,等. 激光表面织构对45钢干摩擦性能的影响[J]. 机械工程学报,2017,53(3):148-154. CHANG Qiuying,QI Ye,WANG Bin,et al. Tribological influence of laser surface textures on 45 steel under dry sliding[J]. Journal of Mechanical Engineering,2017,53(3):148-154.
[40] 方亮,杜道山,张晓峰,等. 三体磨损中的塑性变形磨损[J]. 西安交通大学学报,2003,37(2):111-114. FANG Liang,DU Daoshan,ZHANG Xiaofeng,et al. Plastic deformation wear in three-body abrasion[J]. Journal of Xi'an Jiaotong University,2003,37(2):111-114.

磨料粒度对表面微织构纯钛干摩擦性能的影响

Effect of Wear Particle Size on Dry Tribological Properties of Surface Texturing Titanium

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	倪陈兵, 朱立达, 宁晋生, 杨志超, 刘长福. 超声振动辅助铣削钛合金铣削力信号及切屑特征研究[J]. 机械工程学报, 2019, 55(7): 207-216.
[2]	高泽, 张德远, 李哲, 姜兴刚, 刘佳佳. 高速超声椭圆振动铣削腹板表面质量研究[J]. 机械工程学报, 2019, 55(7): 249-256.
[3]	余陈, 陈静, 陈怀宁, 张宇鹏, 房卫萍. TC4钛合金磁控窄间隙TIG焊试板热处理前后三维应力[J]. 机械工程学报, 2019, 55(6): 61-66.
[4]	丁宝洋, 白倩, 刘具龙, 张璧. 基于Simulink反馈方法的钛合金铣削刀具磨损预测[J]. 机械工程学报, 2019, 55(11): 224-232.
[5]	黎海旭, 唐鹏, 吴正涛, 代伟, 王启民, 祁正兵. TiSiN/AlCrN纳米多层涂层高温热稳定性及摩擦学特性研究[J]. 机械工程学报, 2018, 54(6): 32-40.
[6]	何耿煌, 吴明阳, 李凌祥, 邹伶俐, 程程. 典型钛合金切削层相变形成机理及其影响因素研究[J]. 机械工程学报, 2018, 54(17): 133-141.
[7]	马国政, 雍青松, 王海斗, 何鹏飞, 徐滨士. 调制周期对纳米多层类石墨薄膜力学性能及摩擦学性能的影响[J]. 机械工程学报, 2018, 54(15): 92-99.
[8]	张先炼, 何晓聪, 赵伦, 邢保英. 钛合金薄板自冲铆接工艺及失效行为研究[J]. 机械工程学报, 2018, 54(13): 202-207.
[9]	肖华平, 刘书海, 陈瑜, 王德国. 4种轴承钢在水基泥浆中摩擦学性能研究[J]. 机械工程学报, 2018, 54(13): 153-158.
[10]	马浩, 高殿荣, 毋少峰, 梁瑛娜. 水压马达仿生非光滑表面配流副摩擦磨损研究[J]. 机械工程学报, 2018, 54(13): 142-152.
[11]	顾军, 张朝辉, 黄宝成, 王磊, 李宽宽. 丙二醇无规共聚醚水溶液的摩擦学性能研究[J]. 机械工程学报, 2018, 54(1): 144-149.
[12]	赵德望, 任大鑫, 赵坤民, 郭杏林, 杨文平. 工艺参数对镁钛异质金属超声波点焊接头拉伸性能及疲劳性能的影响[J]. 机械工程学报, 2017, 53(24): 118-125.
[13]	李东, 刘志刚, 王伊卿, 洪军, 卢秉恒. 大面积钛合金电火花加工放电产物运动规律研究[J]. 机械工程学报, 2017, 53(21): 200-208.
[14]	邓德伟, 于涛, 张林, 杨树华, 张洪潮. 脉冲电流-激光复合愈合钛合金深层裂纹微观组织研究[J]. 机械工程学报, 2017, 53(20): 38-44.
[15]	邵振宇, 李哲, 张德远, 姜兴刚, 秦威. 钛合金旋转超声辅助钻削的钻削力和切屑研究[J]. 机械工程学报, 2017, 53(19): 66-72.