Study of Shear Hardening Model Considering Non-uniform Hardening Behavior in Shear Zone

doi:10.3901/JME.260046

Abstract

Abstract: The shear test can be used to evaluate the plastic hardening characteristics of metallic materials under cyclic loading and large strain conditions. However, the existence of end and boundary effects in such tests leads to strain non-uniformity in the deformation zone, resulting in hardening discrepancies that limit the applicability of the tests. A double-groove shear test was conducted on Q890 high-strength steel and AA2219-O aluminum alloy to investigate the influence of strain non-uniformity in the shear deformation zone on yield and plastic flow. A shear stress-strain analytical model was established, considering the hardening discrepancies caused by the non-uniform strain distribution. The accuracy of the model was validated through a comparison with small-hole tensile tests and simulation analysis. The results show that the shear strain decreases gradually from the edge to the center of the shear zone at the same moment of deformation, for Q890 high-strength steel and AA2219-O aluminum alloy, the strains at the edge increases by 6.30% and 12.90%, respectively, compared with that at the center point; the inaccuracy of the prediction of the stress results of the double-tension zone will be caused by not taking the non-uniformity of shear strain into consideration, for Q890 high-strength steel and AA2219-O aluminum alloy, the maximum differences of yield trajectory calibrated by different regional strains are 82 MPa and 19 MPa, respectively, with relative differences of 8.80% and 32.80%; at the same stress level, for Q890 high-strength steel and AA2219-O aluminum alloy, the edge strains increased by up to 26% and 47% over center point strains, respectively; and the prediction error for the necking zone wall thickness of the small-hole tensile test is as high as 9%. After considering the non-uniformity of shear strain, the proposed model will significantly improve the wall thickness prediction accuracy in the necking zone of small-hole tensile test, and the wall thickness prediction error in the necking zone is less than 1%.

Key words: Q890 high-strength steel, AA2219-O aluminum alloy, double groove shear specimen, shear test, non-uniform hardening

CLC Number:

TG156

LIN Yanli, XU Enqi, SU Yibo, QIAN Quan, LI Yuetong, HE Zhubin. Study of Shear Hardening Model Considering Non-uniform Hardening Behavior in Shear Zone[J]. Journal of Mechanical Engineering, 2026, 62(2): 181-194.

Add to citation manager EndNote|Reference Manager|ProCite|BibTeX|RefWorks

URL: http://www.cjmenet.com.cn/EN/10.3901/JME.260046

http://www.cjmenet.com.cn/EN/Y2026/V62/I2/181

References

[1] BOUVIER S, GARDEY B, HADDADI H, et al.Characterization of the strain-induced plastic anisotropy of rolled sheets by using sequences of simple shear and uniaxial tensile tests[J]. Journal of Materials Processing Technology,2006,174(1-3):115-126.
[2] THUILLIER S,MANACH P Y. Comparison of the work-hardening of metallic sheets using tensile and shear strain paths[J]. International Journal of Plasticity,2009,25(5):733-751.
[3] CHOI J S,LEE J W,KIM J H,et al. Measurement and modeling of simple shear deformation under load reversal:Application to advanced high strength steels[J].International Journal of Mechanical Sciences,2015,98:144-156.
[4] MUHAMMAD W,KANG J,MISHRA R K,et al. A simple approach to performing large strain cyclic simple shear tests:Methodology and experimental results[J].Journal of Testing and Evaluation, 2018, 46(6):2604-2615.
[5] TARIGOPULA V,HOPPERSTAD O S,LANGSETH M,et al. A study of large plastic deformations in dual phase steel using digital image correlation and FE analysis[J].Experimental Mechanics,2008,48:181-196.
[6] LOU Y,ZHANG S,YOON J W. Strength modeling of sheet metals from shear to plane strain tension[J].International Journal of Plasticity,2020,134:102813.
[7] DU Kai, HUANG Shaohui, HOU Yong, et al.Characterization of the asymmetric evolving yield and flow of 6016-T4 aluminum alloy and DP490 steel[J].Journal of Materials Science&Technology,2023,133:209-229.
[8] LI Shuhui,HE Ji,GU Bin,et al. Anisotropic fracture of advanced high strength steel sheets:Experiment and theory[J]. International Journal of Plasticity,2018,103:95-118.
[9] MIYAUCHI K. A proposal of a planar simple shear test in sheet metals[J]. Sci. Paper Inst. Phys. Chem. Res.,1984:78:27-42.
[10] PHAM C H,ADZIMA F,COËR J,et al. Anti-Buckling device for Ultra-Thin metallic sheets under large and reversed shear strain paths[J]. Experimental Mechanics,2017,57(4):593-602.
[11] G’SELL C,BONI S,SHRIVASTAVA S. Application of the plane simple shear test for determination of the plastic behaviour of solid polymers at large strains[J]. Journal of Materials Science,1983,18(3):903-918.
[12] BOUVIER S,HADDADI H,LEVÉE P,et al. Simple shear tests:Experimental techniques and characterization of the plastic anisotropy of rolled sheets at large strains[J].Journal of Materials Processing Technology,2006,172(1):96-103.
[13] AN Y G,VEGTER H,HEIJNE J. Development of simple shear test for the measurement of work hardening[J].Journal of Materials Processing Technology,2009,209(9):4248-4254.
[14] YAN Geng,LIN Yanli,WANG Shuo,et al. Experiment for measuring mechanical properties of high-strength steel sheets under cyclic loading by V-shaped double-shear-zone specimens[J]. Materials,2023,16(13):4645.
[15] WANG Y B,LYU Y F,WANG Y Z,et al. A reexamination of high strength steel yield criterion[J]. Construction and Building Materials,2020,230:116945.
[16] LI Z X,ZHAN M,FAN X G,et al. Age hardening behaviors of spun 2219 aluminum alloy component[J].Journal of Materials Research and Technology-Jmr&T,2020,9(3):4706-4716.
[17] DRUCKER D C,PRAGER W. Soil mechanics and plastic analysis or limit design[J]. Quarterly of Applied Mathematics,1952,10(2):157-165.
[18] HOLLOMON J H. The effect of heat treatment and carbon content on the work hardening characteristics of several steel[J]. Transactions of ASM,1944,32:123-133.
[19] LIN Yanli,SU Yibo,ZHAO Qilin,et al. A new regression model for the prediction of the stress–strain relations of different materials[J]. Materials,2023,16(22):7145.
[20] LEVENBERG K. A method for the solution of certain nonlinear problems in least squares[J]. Quarterly Journal of Applied Mathematics,1944,2(2):164-168.
[21] MARQUARDT D W. An algorithm for least-squares estimation of nonlinear parameters[J]. Journal of the Society for Industrial and Applied Mathematics,1963,11(2):431-441.