激光表面毛化对Ti/K9玻璃扩散焊接头性能的影响

doi:10.3901/JME.2023.14.130

机械工程学报 ›› 2023, Vol. 59 ›› Issue (14): 130-137.doi: 10.3901/JME.2023.14.130

扫码分享

激光表面毛化对Ti/K9玻璃扩散焊接头性能的影响

王美荣^1,2, 陈敏^1,2, 蒋嘉豪^1,2, 宋晓国^1,2, 唐冬雁³, 曹健^1,2

1. 哈尔滨工业大学先进焊接与连接国家重点实验室哈尔滨 150001;
2. 哈尔滨工业大学(威海)山东省特种焊接技术重点实验室威海 264209;
3. 哈尔滨工业大学化工与化学学院哈尔滨 150001

收稿日期:2022-01-29 修回日期:2022-12-11 出版日期:2023-07-20 发布日期:2023-08-16
通讯作者: 王美荣(通信作者),女,1979年出生,博士,讲师,硕士研究生导师。主要研究方向为新型材料制备、异种材料连接。E-mail:wmr21c@163.com
作者简介:陈敏,女,1994年出生。主要研究方向为异种材料连接。E-mail:cm769018986@163.com
基金资助:
山东省重大科技创新工程(2019JZZY010330)和先进焊接与连接国家重点实验室开放课题研究基金(AWJ-21M19)资助项目。

Effect of Laser Texturing Technology on Joint Properties of Ti to K9 Glass Diffusion Bonding

WANG Meirong^1,2, CHEN Min^1,2, JIANG Jiahao^1,2, SONG Xiaoguo^1,2, TANG Dongyan³, CAO Jian^1,2

1. State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001;
2. Shandong Provincial Key Lab of Special Welding Technology, Harbin Institute of Technology at Weihai, Weihai 264209;
3. School of Chemistry and Chemical Engineering, Harbin Institute of Technology, Harbin 150001

Received:2022-01-29 Revised:2022-12-11 Online:2023-07-20 Published:2023-08-16

摘要/Abstract

摘要： 针对Ti与K9玻璃因化合键差异难以形成有效连接的问题，采用纳秒激光毛化处理工艺改变Ti表面结构，实现了其与K9玻璃的真空扩散连接。通过光学显微镜、扫描电子显微镜、X射线衍射仪和万能试验机等分析测试技术手段对激光表面毛化后的Ti表面及Ti/K9玻璃接头的微观组织形貌、物相组成以及力学性能进行表征。结果表明，Ti经激光毛化处理后，形成横纵交错的刻痕，刻痕附近发生熔化再结晶产生凸起，并伴随Ti-O化合物及Ti-N化合物生成；随着激光加工次数增加，Ti-N化合物含量增加而Ti-O化合物含量减少，接头剪切强度呈现先升高后降低的趋势，表明Ti-N化合物含量过多会引起接头强度降低；当激光扫描次数为15次时，接头剪切强度达到最大值，为13.1 MPa；经能谱分析，在Ti/K9界面处伴随有Ti、Si等元素的扩散和化学反应。采用激光蚀刻技术有助于增强元素的活性，在一定程度上促进了元素扩散和化学结合。

关键词: 扩散连接, K9玻璃, 工业纯钛, 激光表面毛化, 显微结构

Abstract: For the problem that Ti and K9 glass are difficult to form an effective bonding due to the difference of chemical bonds, nanosecond laser texturing of Ti developed with which the diffusion bonding of Ti and K9 glass was achieved. The microstructure, phase composition, and mechanical properties of laser-textured Ti and Ti/K9 glass joint were characterized by optical microscope(OM), scanning electron microscope(SEM), X-ray diffractometer(XRD), and universal material testing machine. The results show that the interconnected networks were produced on the Ti surface after laser texturing, where melting and recrystallization occurred, with the formation of Ti-O and Ti-N compounds. With the increase of laser processing times, the content of Ti-N compounds was increased while the content of Ti-O compounds was decreased, and the shear strength of the joint increased first then decreased which indicates that the over-increased Ti-N compounds resulted in the decrease of the joint strength. The maximum shear strength of 13.1 MPa was obtained when the 15th laser processing was adopted. The energy dispersive scanning(EDS) analysis showed that chemical reaction and atomic diffusion among Ti, Si, and other elements between Ti and K9 glass at the bonding interface were detected. Laser texturing Ti is helpful to enhance the activity of elements, which helps promote elemental diffusion and chemical reaction.

Key words: diffusion bonding, K9 glass, Ti, laser texturing, microstructure

中图分类号:

TG453

王美荣, 陈敏, 蒋嘉豪, 宋晓国, 唐冬雁, 曹健. 激光表面毛化对Ti/K9玻璃扩散焊接头性能的影响[J]. 机械工程学报, 2023, 59(14): 130-137.

WANG Meirong, CHEN Min, JIANG Jiahao, SONG Xiaoguo, TANG Dongyan, CAO Jian. Effect of Laser Texturing Technology on Joint Properties of Ti to K9 Glass Diffusion Bonding[J]. Journal of Mechanical Engineering, 2023, 59(14): 130-137.

参考文献

[1] 王美荣,雷玉珍,唐冬燕,等. 钎焊时间对K9玻璃/B₂O₃-Bi₂O₃-TiO₂/纯钛钎焊接头组织和性能影响[J]. 焊接学报,2019,40(1):80-83. WANG Meirong,LEI Yuzhen,TANG Dongyan,et al. Effect of holding time on the interfacial microstructure and mechanical properties of K9 glass/B₂O₃-Bi₂O₃-TiO₂/pure Ti brazing joints[J]. Transactions of the China Welding Institution,2019,40(1):80-83.
[2] 王震,程雪岷. 快速反射镜研究现状及未来发展[J]. 应用光学,2019,40(3):373-379. WANG Zhen,CHENG Xuemin. Research progress and development trend of fast steering mirror[J]. Journal of Applied Optics,2019,40(3):373-379.
[3] BOROWITZ M. Strategic implications of the proliferation of space situational awareness technology and information:Lessons learned from the remote sensing sector[J]. Space Policy,2018,47(1):18-27.
[4] SANDERS K,MASRI S. The energy-water agriculture nexus:The past, present and future of holistic resource management via remote sensing technologies[J]. Journal of Cleaner Production,2016,117(1):73-88.
[5] BRAZ C,VENTURA C,OLIVEIRA M,et al. Investigating the application of customized abrasive cutoff wheels with respect to tool wear and subsurface integrity in metallographic cutting of pure titanium[J]. Metallography,Microstructure,and Analysis,2019,8(6):826-832.
[6] MLGA B,XBWA B,PPGB C,et al. Properties of hydrophobic carbon-PTFE composite coating with high corrosion resistance by facile preparation on pure Ti[J]. Transactions of Nonferrous Metals Society of China,2019,29(11):2321-2330.
[7] XU S Z,YAO C Z,DOU H Q,et al. An investigation on 800 nm femtosecond laser ablation of K9 glass in air and vacuum[J]. Applied Surface Science,2017,406(6):91-98.
[8] YANG C. Remote Sensing and precision agriculture technologies for crop disease detection and management with a practical application example[J]. Engineering,2020,6(5):528-532.
[9] ELREFAEY A,JANCZAK-RUSCH J,KOEBEL M M. Direct glass-to-metal joining by simultaneous anodic bonding and soldering with activated liquid tin solder[J]. Journal of Materials Processing Technology,2014,214(11):2716-2722.
[10] 徐兴文. 钛合金与玻璃的激光透射焊接实验研究、工艺优化及数值模拟[D]. 镇江:江苏大学,2018. XU Xingwen. Experimental study, process optimization and numerical simulation of laser transmission welding of titanium alloy and glass[D]. Zhenjiang:Jiangsu University,2018.
[11] ROCHA L A,BARBOSA M A,PUERS R. Active metal brazing for joining glass-ceramic to titanium-a study on silver enrichment[J]. Journal of Materials Science:Materials in Medicine,1995,6(12):835-838.
[12] DONALD I W,MALLINSON P M,METCALFE B L,et al. Recent developments in the preparation, characterization and applications of glass-and glass-ceramic-to-metal seals and coatings[J]. Journal of Materials Science,2011,46(7):1975-2000.
[13] HU L F,XUE Y Z,WANG H. Glass-Cu joining by anodic bonding and soldering with eutectic Sn-9Zn solder[J]. Journal of Alloys and Compounds,2019,789(1):558-566.
[14] 孙磊强,赵作福,莫梓睿,等. 激光技术在材料表面改性方面的研究进展[J]. 辽宁工业大学学报(自然科学版),2018,38(6):378-381. SUN Leiqiang,ZHAO Zuofu,MO Zirui,et al. Research progress of laser technology in surface modification of materials[J]. Journal of Liaoning University of Technology(Natural Science Edition),2018,38(6):378-381.
[15] 丁旭,罗海龙. 激光技术在材料加工领域的应用探究[J]. 信息记录材料,2019,20(9):34-37. DING Xu,LUO Hailong. Research on the application of laser technology in the field of material processing[J]. Information Recording Materials,2019,20(9):34-37.
[16] MOURA C G,CARVALHO O,GONÇALVES L M V,et al. Laser surface texturing of Ti-6Al-4V by nanosecond laser:Surface characterization, Ti-oxide layer analysis and its electrical insulation performance[J]. Materials Science and Engineering:C,2019,104(109901):1-11.
[17] TAN C W,SU J H,FENG Z W,et al. Laser joining of CFRTP to titanium alloy via laser surface texturing[J]. Chinese Journal of Aeronautics,2021,34(5):103-114.
[18] O'HANA S,PINKERTON A J,SHOBA K,et al. Laser surface colouring of titanium for contemporary jewellery[J]. Surface Engineering,2008,24(2):147-153.
[19] PINO A,FERNáNDEZ-PRADAS J M,SERRA P,et al. Coloring of titanium through laser oxidation:Comparative study with anodizing[J]. Surface and Coatings Technology,2004,187(1):106-112.
[20] KANG Z,FU Y,JI J,et al. Effect of local laser surface texturing on tribological performance of injection cam[J]. The International Journal of Advanced Manufacturing Technology,2017,92(1):1751-1760.
[21] KONONENKO T V,FREITAG C,SOVYK D N,et al. Influence of pulse repetition rate on percussion drilling of Ti-based alloy by picosecond laser pulses[J]. Optics and Lasers in Engineering,2018,103(1):65-70.
[22] 杨奇彪,张弘,周维,等. 飞秒激光诱导硬质合金YG6表面累积效应[J]. 光子学报,2019,48(6):70-76. YANG Qibiao,ZHANG Hong,ZHOU Wei,et al. Surface incubation effect of carbide YG6 induced by femto second laser[J]. Acta Photonica Sinica,2019,48(6):70-76.
[23] KAPLAN A,BERGSTRÖM D,POWELL J. Absorptance of nonferrous alloys to Nd:YLF and Nd:YAG laser light at room temperature[J]. Applied Optics,2007,46(8):1290-1301.
[24] 谭向虎,单际国,唐磊,等. 面向碳纤维增强树脂基复合材料/钢异质结构连接的汽车钢板高速激光毛化工艺研究[J]. 中国激光,2015,42(3):54-60. TAN Xianghu,SHAN Jiguo,TANG Lei,et al. Study on laser surfi-sculpt of GMW2 autobody sheet steel for carbon fiber reinforced polymer/steel dissimilar joint[J]. Chinese Journal of Lasers,2015,42(3):54-60.
[25] 李海刚,毕建勋,马武军,等. 激光毛化对Cf/SiC与TC4钎焊接头组织及性能的影响[J]. 宇航材料工艺,2017,47(1):42-46. LI Haigang,BI Jianxun,MA Wujun,et al. Influence of laser roughing technology on microstructure and properties of Cf/SiC-TC4 brazing joints[J]. Aerospace Materials & Technology,2017,47(1):42-46.
[26] 崔开放,钟良,龚伟,等. 陶瓷表面激光无钯活化及其化学镀镍[J]. 激光技术,2018,42(5):622-626. CUI Kaifang,ZHONG Liang,GONG Wei,et al. Palladium free activation and electroless nickel plating on ceramic surface[J]. Laser Technology,2018,42(5):622-626.
[27] 代竟雄,钟良,龚伟,等. ABS塑料表面化学镀铜激光无钯活化新工艺[J]. 化工进展,2018,37(7):2759-2764. DAI Jingxiong,ZHONG Liang,GONG Wei,et al. A new laser assisted palladium-free activation technology for ABS plastic surface electroless copper plating[J]. Chemical Industry and Engineering Progress,2018,37(7):2759-2764.
[28] 刘星. 建筑用玻璃与不锈钢/钛合金的激光焊接工艺及性能研究[D]. 苏州:苏州大学,2015. LIU Xing. Study on process and performance of glass to stainless steel/titanium alloy with laser welding[D]. Suzhou:Soochow University,2015.

激光表面毛化对Ti/K9玻璃扩散焊接头性能的影响

Effect of Laser Texturing Technology on Joint Properties of Ti to K9 Glass Diffusion Bonding

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 9

编辑推荐

Metrics

本文评价

[1]	戴剑博, 苏宏华, 王忠宾, 丁文锋, 傅玉灿, 陈佳佳. 多晶碳化硅陶瓷磨削裂纹损伤形成机理研究[J]. 机械工程学报, 2022, 58(13): 307-320.
[2]	杨冰, JAMES M N. 基于CJP模型的疲劳裂纹扩展率曲线及应用方法[J]. 机械工程学报, 2018, 54(18): 76-84.
[3]	方爽, 熊华平, 程耀永, 林海, 于秋颖, 任新宇, 王淑云. Ti₂AlNb粉末与Ti/Al纳米叠层箔带混合烧结高温微叠层材料的微观结构^*[J]. 机械工程学报, 2017, 53(6): 73-79.
[4]	张飞虎, 李琛, 孟彬彬, 赵航, 刘忠德. 基于变切深纳米刻划的K9玻璃表面成形特征及去除机制研究^*[J]. 机械工程学报, 2016, 52(17): 65-71.
[5]	李军, 王慧敏, 王文泽, 黄建东, 朱永伟, 左敦稳. 固结磨料研磨K9玻璃表面粗糙度模型[J]. 机械工程学报, 2015, 51(21): 199-205.
[6]	刘雨生, 李萍, 王斌, 李贝贝, 薛克敏. Ti2AlNb合金多层板结构超塑成形/扩散连接数值模拟及试验研究[J]. 机械工程学报, 2015, 51(12): 43-49.
[7]	许崇海;吴光永;张永莲;衣明东;肖光春;方斌. 多元梯度自润滑陶瓷刀具材料的研制[J]. , 2014, 50(7): 94-101.
[8]	廖宗博;国为民;赵明汉;董建新;张麦仓;曾强;张龙飞;燕平. K418B和FGH91双合金热等静压扩散连接的动力学模拟研究[J]. , 2013, 49(20): 170-175.
[9]	吴诗惇;向毅斌. 预测钛合金超塑成形－扩散连接(SPF/DB)界面层的断裂韧度[J]. , 2002, 38(11): 84-87.