热处理对增材制造AlSi10Mg超精密车削特性的影响机理

doi:10.3901/JME.2022.19.315

机械工程学报 ›› 2022, Vol. 58 ›› Issue (19): 315-330.doi: 10.3901/JME.2022.19.315

• 制造工艺与装备 • 上一篇

扫码分享

热处理对增材制造AlSi10Mg超精密车削特性的影响机理

白玉超^1,2,3, 陈杰^1,2, 刘林青¹, 韦雄棉¹, 王迪¹

1. 华南理工大学机械与汽车工程学院广州 510640;
2. 新加坡国立大学机械工程学院新加坡 117575;
3. 苏州工业园区新国大研究院苏州 215123

收稿日期:2021-10-22 修回日期:2022-07-04 出版日期:2022-10-05 发布日期:2023-01-05
通讯作者: 王迪(通信作者)，男，1986年出生，博士，教授，博士研究生导师。主要研究方向为增材制造与激光加工技术开发与应用。E-mail：mewdlaser@scut.edu.cn
作者简介:白玉超，男，1988年出生，博士，研究员。主要研究方向为金属激光增材制造及其后处理。E-mail：mpeby@nus.edu.sg
基金资助:
广东省基础与应用基础资助项目(2019B1515120094)。

Influence Mechanism of Heat Treatment on Ultra-precision Turning Characteristics of Additively Manufactured AlSi10Mg Parts

BAI Yuchao^1,2,3, CHEN Jie^1,2, LIU Linqing¹, WEI Xiongmian¹, WANG Di¹

1. School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510640;
2. Department of Mechanical Engineering, National University of Singapore, Singapore 117575;
3. Laboratory of National University of Singapore, Suzhou Research Institute, Suzhou 215123

Received:2021-10-22 Revised:2022-07-04 Online:2022-10-05 Published:2023-01-05

摘要/Abstract

摘要： 由于激光选区熔化(增材制造)直接成型的AlSi10Mg合金零件表面相对粗糙，很难满足对表面精度要求高的行业需求。而具有获取纳米级表面精度能力的超精密加工为提高激光选区熔化零件的表面质量提供了有前景的后处理解决方案。采用金刚石刀具分别对直接成型、低温退火、固溶处理以及时效处理后的AlSi10Mg合金的微量切削特性进行研究，讨论微观组织演变与切削参数对AlSi10Mg合金的超精密切削特性的影响机理，揭示热处理状态对切削力、切削表面质量与切屑形貌等的影响规律。以探索快速高效地将成型零件表面质量提高到镜面水平的方法。结果表明：激光选区熔化直接成型的AlSi10Mg合金微观组织以微米级的网格结构为主，其显微维氏硬度和切削力均大于热处理后的样品；切削力同时受到合金的微观组织和力学性能的综合影响；直接成型的样品沟槽表面质量最好，低温退火样品次之，固溶处理样品最差；高温热处理后形成的大块的Si颗粒会增加切屑的脆性，并降低样品的X轴切削力；增加切削深度和切削速度均会导致切削力的增加和表面质量的恶化，且切削深度对切削力和表面质量的影响更大；直接成型样品的镜面加工质量最好，表面粗糙度(Ra)数值可降低到11.2 nm，远低于直接成型样品的～10 µm。本研究为实现激光选区熔化成立铝合金零件的表面质量提升到镜面水平提供了理论和应用参考。

关键词: 激光选区熔化, AlSi10Mg合金, 超精密切削, 微观组织, 可加工性

Abstract: The surface quality of AlSi10Mg alloy fabricated directly by selective laser melting (SLM) technology generally shows insufficient surface quality, which cannot meet the stringent requirements of some industries for high accuracy in precision engineering. To this end, ultra-precision machining provides a promising post-processing solution for augmented surface quality on SLM parts. In this study, diamond tools were used to investigate the micro-cutting characteristics of as-built, annealed, solution-treated and ageing-treated SLM-AlSi10Mg alloy. The influence of microstructure evolution and cutting parameters on the ultra-precision machining characteristics of AlSi10Mg alloy was discussed. The effect of heat treatment on cutting force, cutting surface quality and chip morphology was revealed aiming to identify the methods to quickly and efficiently improve the surface quality of SLM parts to achieve mirror-surface finishing. The results show that the microstructure of the as-built AlSi10Mg alloy is dominated by a micron-level cellular structure, and its micro Vickers hardness and cutting force are greater than that of the heat-treated sample. The cutting force is simultaneously affected by the microstructure and mechanical properties of the alloy. The surface quality of the grooves of the as-built sample is the best, followed by annealed, ageing-treated and solution-treated samples. The large Si particles formed after high-temperature heat treatment will lead to brittleness of the chips and reduce the X-axis cutting force. Increasing the depth of cut and cutting speed will cause the increase in cutting force and poor surface quality, where the effect of the former factor is more pronounced. Through the present study, the best surface roughness has been improved to 11.2 nm by 3 orders of magnitude from ～10 µm of the as-built sample by SLM. This study provides a theoretical and application reference for the improvement of the surface quality of SLM aluminium alloy parts to the nanometric level.

Key words: selective laser melting, AlSi10Mg alloy, ultra-precision machining, microstructure, machinability

中图分类号:

TG519

白玉超, 陈杰, 刘林青, 韦雄棉, 王迪. 热处理对增材制造AlSi10Mg超精密车削特性的影响机理[J]. 机械工程学报, 2022, 58(19): 315-330.

BAI Yuchao, CHEN Jie, LIU Linqing, WEI Xiongmian, WANG Di. Influence Mechanism of Heat Treatment on Ultra-precision Turning Characteristics of Additively Manufactured AlSi10Mg Parts[J]. Journal of Mechanical Engineering, 2022, 58(19): 315-330.

参考文献

[1] DEBROY T，WEI H L，ZUBACK J S，et al. Additive manufacturing of metallic components-process，structure and properties[J]. Progress in Materials Science，2018，92:112–224.
[2] 杨永强，陈杰，宋长辉，等. 金属零件激光选区熔化技术的现状及进展[J]. 激光与光电子学进展，2018，55(1):9-21. YANG Yongqiang，CHEN Jie，SONG Changhui，et al. Current status and progress on technology of selective laser melting of metal parts[J]. Laser & Optoelectronics Progress，2018，55(1):9-21.
[3] BAI Yuchao，FU Fan，XIAO Zefeng，et al. Progress in selective laser melting equipment，related biomedical metallic materials and applications[J]. Journal of Zhejiang University Science A，2018，19:122-136.
[4] BAI Yuchao，ZHAO Cuiling，YANG Jin，et al. Microstructure and machinability of selective laser melted high-strength maraging steel with heat treatment[J]. Journal of Materials Processing Technology，2020，116906.
[5] NI Chenbing，ZHU Lida，ZHENG Zhongpeng，et al. Effect of material anisotropy on ultra-precision machining of Ti-6Al-4V alloy fabricated by selective laser melting[J]. Journal of Alloys and Compounds，2020，848:156457.
[6] ZHANG S J，TO S，WANG S J，et al. A review of surface roughness generation in ultra-precision machining[J]. International Journal of Machine Tools and Manufacture，2015，91:76–95.
[7] 徐超，彭小强，戴一帆. 复杂曲面铝反射镜超精密制造现状[J]. 光电工程，2020，47(8):200147. XU Chao，PENG Xiaoqiang，DAI Yifan. Current status of ultra-precision manufacturing of complex curved aluminum reflectors[J]. Opto-Electronic Engineering，2020，47(8):200147.
[8] 林杰. 超精密加工铝反射镜表面形貌建模及散射特性研究[D]. 哈尔滨:哈尔滨工业大学，2018. LIN Jie. Research on surface topography modeling and scattering properties of ultra-precision machining aluminium mirrors[D]. Harbin:Harbin Institute of Technology，2018.
[9] 徐超，胡皓，彭小强，等. 复杂曲面铝反射镜磁流变抛光工艺优化[J]. 航空学报，2021，42(10):524914. XU Chao，HU Hao，PENG Xiaoqiang，et al. Optimization of magnetorheological polishing for aluminum mirror with complex surface[J]. Acta Aeronautica et Astronautica Sinica，2021，42(10):524914.
[10] 王海龙. 6061铝合金超精密金刚石切削表面生成机理研究[D]. 广州:广东工业大学，2020. WANG Hailong. Investigation on surface generation mechanism of ultra-precision diamond cutting for aluminum alloy 6061[D]. Guangzhou:Guangdong University of Technology，2020.
[11] 汪兴均. 10B/Al复合材料超精密切削微观表面成形机理与实验研究[D]. 成都:电子科技大学，2019. WANG Xingjun. Micro-surface formation mechanism and experimental study in ultra-precision cutting 10B/Al composite[D]. Chengdu:University of Electronic Science and Technology of China，2019.
[12] SAUNDERS I J，PLOEG L，DORREPAAL M，et al. Fabrication and metrology of freeform aluminum mirrors for the SCUBA-2 instrument[J]. Optical Manufacturing and Testing VI，2005，5869:586905.
[13] BEIER M，HARTUNG J，PESCHEL T，et al. Development，fabrication，and testing of an anamorphic imaging snap-together freeform telescope[J]. Applied Optics，2015，54:3530.
[14] MARTIN J H，YAHATA B D，HUNDLEY J M，et al. 3D printing of high-strength aluminium alloys[J]. Nature，2017，549:365-369.
[15] YANG Tao，LIU Tingting，LIAO Wenhe，et al. The influence of process parameters on vertical surface roughness of the AlSi10Mg parts fabricated by selective laser melting[J]. Journal of Materials Processing Technology，2019，266:26-36.
[16] 史振伟，王敏杰，戚文军，等. 激光选区熔化3D打印AlSi10Mg合金的铺粉厚度[J]. 中国机械工程，2022，33(8):959-964. SHI Zhenwei，WANG Minjie，QI Wenjun，et al. Study of layer thickness on laser selective melting of 3D printed AlSi10Mg alloy[J]. China Mechanical Engineering，2022，33(8):959-964.
[17] 韩潇，康楠，焦建超，等. 选区激光熔化AlSi10Mg合金镜的表面性能[J]. 中南大学学报，2020，51(11):3088-3092. HAN Xiao，KANG Nan，JIAO Jianchao，et al. Surface characteristic of selective laser melted AlSi10Mg mirrors[J]. Journal of Central South University，2020，51(11):3088-3092.
[18] BAI Yuchao，SHI Zhuoqi，LEE Y J，et al. Optical surface generation on additively manufactured AlSiMg0.75 alloys with ultrasonic vibration-assisted machining[J]. Journal of Materials Processing Technology，2020，280:116597.
[19] HILPERT E，HARTUNG J，RISSE S，et al. Precision manufacturing of a lightweight mirror body made by selective laser melting[J]. Precision Engineering，2018，53:310-317.
[20] GUO Peng，ZOU Bin，HUANG Chuanzhen，et al. Study on microstructure，mechanical properties and machinability of efficiently additive manufactured AISI 316L stainless steel by high-power direct laser deposition[J]. Journal of Materials Processing Technology，2017，240:12-22.
[21] TO S，LEE W B，CHAN C Y. Ultraprecision diamond turning of aluminium single crystals[J]. Journal of Materials Processing Technology，1997，63:157-162.
[22] BAI Yuchao，ZHAO Cuiling，ZHANG Yu，et al. Additively manufactured CuCrZr alloy:Microstructure，mechanical properties and machinability[J]. Materials Science and Engineering:A，2021，819:141528.
[23] CHAUDHARI A，SOH Z Y，WANG Hao，et al. Rehbinder effect in ultraprecision machining of ductile materials[J] International Journal of Machine Tools and Manufacture，2018，133:47-60.
[24] CHAUDHARI A，WANG Hao. Effect of surface-active media on chip formation in micromachining[J]. Journal of Materials Processing Technology，2019，271:325-335.

热处理对增材制造AlSi10Mg超精密车削特性的影响机理

Influence Mechanism of Heat Treatment on Ultra-precision Turning Characteristics of Additively Manufactured AlSi10Mg Parts

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	李坤, 吉辰, 白生文, 蒋斌, 潘复生. 高性能镁合金电弧增材制造技术研究现状与展望[J]. 机械工程学报, 2024, 60(7): 289-311.
[2]	陈伟, 赵杰, 朱利斌, 曹海波. 增材制造低活化钢研究现状及展望[J]. 机械工程学报, 2024, 60(7): 312-333.
[3]	郑洋, 赵梓昊, 刘伟, 余政哲, 牛伟, 雷贻文, 孙荣禄. 高性能镁合金增材制造技术研究进展[J]. 机械工程学报, 2024, 60(7): 385-400.
[4]	张赛凡, 李博, 轩福贞. 激光选区熔化过程声发射信号的降噪与分类预测方法[J]. 机械工程学报, 2024, 60(6): 163-176.
[5]	崔桂涵, 杨春利. 基于高强高韧焊丝的脉冲GMAW焊缝金属强韧化机理研究[J]. 机械工程学报, 2024, 60(4): 326-334.
[6]	马艺星, 杨蔚涛, 关肖虎, 杨旗, 赵同新. TWIP钢/IF钢热轧复合板材的微观结构和界面结合性能[J]. 机械工程学报, 2024, 60(4): 345-356.
[7]	宋军, 唐倩, 罗智超, 冯琪翔, 聂云飞, 任治好. 马氏体时效钢激光选区熔化成形过程介观尺度数值模拟[J]. 机械工程学报, 2024, 60(3): 282-295.
[8]	何春雷, 王姝淇, 李东洋, 耿昆, 陈光, 任成祖. 晶粒对多晶材料超精密切削影响的研究进展[J]. 机械工程学报, 2024, 60(3): 373-392.
[9]	冒爱琴, 陈诗洁, 贾洋刚, 邵霞, 权峰, 张晖, 张义伟, 金莹, 金霞. Al含量对粉末冶金CoCrFeMnNi高熵合金组织结构与性能的影响[J]. 机械工程学报, 2024, 60(20): 134-143.
[10]	褚强, 杨夏炜, 李文亚, 范文龙, 邹阳帆, 郝思洁. 铝锂合金无针搅拌摩擦点焊接头组织演变与强化机制研究[J]. 机械工程学报, 2024, 60(2): 150-158.
[11]	高恺, 顾红历, 李坤. Cr、Si微量元素对钢/铝感应静压焊接接头组织及性能的影响[J]. 机械工程学报, 2024, 60(2): 178-187.
[12]	张家豪, 王磊磊, 张彦霄, 黎一帆, 王晓明, 占小红. 激光熔化沉积TiC/TC4功能梯度材料微观组织与拉伸性能研究[J]. 机械工程学报, 2024, 60(19): 356-366.
[13]	谢云飞, 葛世鹏, 郭震国, 褚强, 张勇, 李文亚. 多层铝箔回填式搅拌摩擦点焊接头显微组织特征[J]. 机械工程学报, 2024, 60(18): 128-137.
[14]	王瑞林, 杨新岐, 唐文珅, 罗庭. AA2024-T3铝合金搅拌摩擦沉积增材组织及性能[J]. 机械工程学报, 2024, 60(18): 146-153.
[15]	王高见, 刘丽, 康丹丹, 叶延洪, 邓德安. Ni含量对高速列车转向架耐候钢焊缝金属微观组织、力学性能及腐蚀行为的影响[J]. 机械工程学报, 2024, 60(18): 163-172.