耦合温度效应晶体塑性的TWIP钢变形行为研究

doi:10.3901/JME.2022.20.283

机械工程学报 ›› 2022, Vol. 58 ›› Issue (20): 283-293.doi: 10.3901/JME.2022.20.283

• 特邀专栏：高性能塑性成形制造(下) • 上一篇下一篇

扫码分享

耦合温度效应晶体塑性的TWIP钢变形行为研究

蔡旺^1,2, 王春晖^1,2, 孙朝阳^1,2, 马晋遥³, 李月敏^1,2, 姜军⁴, 张跃飞³

1. 北京科技大学机械工程学院北京 100083;
2. 金属轻量化成形制造北京市重点实验室北京 100083;
3. 北京工业大学固体微结构与性能研究所北京 100124;
4. 帝国理工学院机械工程系伦敦 SW72AZ 英国

收稿日期:2021-09-26 修回日期:2022-01-27 出版日期:2022-10-20 发布日期:2022-12-27
通讯作者: 孙朝阳(通信作者)，男，1976年出生，博士，教授，博士研究生导师。主要从事塑性加工理论及应用和材料多尺度力学行为研究。E-mail：suncy@ustb.edu.cn
作者简介:蔡旺，男，1996年出生，博士研究生。主要从事TWIP钢塑性变形的微观机理与成形工艺研究。E-mail：18811317098@163.com
基金资助:
国家自然科学基金委员会与英国皇家学会合作交流(51911530209)、国家自然科学基金委员会-中国工程物理研究院NSAF联合基金(U1730121)、中央高校基础科研业务费(FRF-BD-20-08A，FRF-AT-20-09，FRF-GF- 19-003A)和国家自然科学基金基础科学中心(51988101)资助项目。

Investigation of Deformation Behavior of TWIP Steel Using Crystal Plasticity Coupling Temperature Effect

CAI Wang^1,2, WANG Chunhui^1,2, SUN Chaoyang^1,2, MA Jinyao³, LI Yuemin^1,2, JIANG Jun⁴, ZHANG Yuefei³

1. School of Mechanical and Engineering, University of Science and Technology Beijing, Beijing 100083;
2. Beijing Key Laboratory of Lightweight Metal Forming, Beijing 100083;
3. Institute of Microstructure and Property of Advanced Materials, Beijing University of Technology, Beijing 100124;
4. Department of Mechanical Engineering, Imperial College London, London, SW72AZ UK

Received:2021-09-26 Revised:2022-01-27 Online:2022-10-20 Published:2022-12-27

摘要/Abstract

摘要： 为探究TWIP钢高温条件下的塑性变形机理，建立了耦合温度效应的晶体塑性本构模型，考虑温度对TWIP钢滑移和孪生的影响，提出了耦合温度效应的流动法则和硬化法则。结合在500 ℃和750 ℃条件下的原位SEM高温拉伸试验，建立了描述TWIP钢热变形过程的晶体塑性有限元模型。模拟获得不同温度条件下的应力应变曲线、应变硬化率和孪晶体积分数与试验结果相吻合，验证了该模型的正确性。进而，基于所建立的模型研究了温度对TWIP钢塑性变形过程滑移、孪生演化及应变硬化过程的影响规律，结果表明：滑移阻力、孪生阻力和应变硬化率随温度的升高呈不均匀降低的趋势，且断后伸长率呈现降低的趋势，由25 ℃时53.4%降低至750 ℃时16.5%。同时，随温度升高，孪生受到抑制，但滑移受温度的影响较小，表现为滑移主导的塑性变形机制。

关键词: TWIP钢, 塑性变形, 晶体塑性, 温度效应, 原位SEM高温拉伸

Abstract: In order to investigate the deformation mechanism of TWIP steel at high temperature，the crystal plastic constitutive model was established by considering the effect of temperature on slip and twinning of TWIP steel，and the flow law and hardening law of considering temperature effect were proposed. The crystal plastic finite element model of TWIP steel during hot deformation was established by in-situ SEM high temperature tensile tests under 500 ℃ and 750 ℃. The stress-strain curves，strain hardening rates and twin volume fraction at different temperatures obtained by simulation were in agreement with the experimental results，which verified the correctness of the model. Based on the model，the effect of temperature on the slip，twinning and strain hardening of TWIP steel during plastic deformation was researched，the results show that the slip resistance，twinning resistance and strain hardening rate decrease unevenly with the increase of temperature，and the elongation after breaking decreases abnormally，from 53.4% at 25 ℃ to 16.5% at 750 ℃. With the increase of temperature，the twinning is restrained while the slip process is less affected by temperature，which shows the plastic deformation mechanism dominated by slip.

Key words: TWIP steel, plastic deformation, crystal plasticity, temperature effect, in-situ SEM high temperature tensile

中图分类号:

TG142

蔡旺, 王春晖, 孙朝阳, 马晋遥, 李月敏, 姜军, 张跃飞. 耦合温度效应晶体塑性的TWIP钢变形行为研究[J]. 机械工程学报, 2022, 58(20): 283-293.

CAI Wang, WANG Chunhui, SUN Chaoyang, MA Jinyao, LI Yuemin, JIANG Jun, ZHANG Yuefei. Investigation of Deformation Behavior of TWIP Steel Using Crystal Plasticity Coupling Temperature Effect[J]. Journal of Mechanical Engineering, 2022, 58(20): 283-293.

参考文献

[1] DE COOMAN B C，ESTRIN Y，KIM S K. Twinning-induced plasticity (TWIP) steels[J]. Acta Materialia，2018，142:283-362.
[2] GRASSEL O，KRUGER L，FROMMEYER G，et al. High strength Fe-Mn-(Al, Si) TRIP/TWIP steels development-properties-application[J]. International Journal of Plasticity，2000，16(10):1391-1409.
[3] 孙朝阳，郭祥如，黄杰，等. 耦合孪生的TWIP钢单晶体塑性变形行为模拟研究[J]. 金属学报，2015，51(3):357-363. SUN Chaoyang，GUO Xiangru，HUANG Jie，et al. Modelling of plastic deformation on coupling twinning of single crystal TWIP steel[J]. Acta Metallurgica Sinica，2015，51(3):357-363.
[4] SHTERNER V，TIMOKHINA I B，BELADI H. On the work-hardening behaviour of a high manganese TWIP steel at different deformation temperatures[J]. Materials Science and Engineering:A，2016，669:437-446.
[5] CURTZE S，KUOKKALA V T. Dependence of tensile deformation behavior of TWIP steels on stacking fault energy，temperature and strain rate[J]. Acta Materialia，2010，58(15):5129-5141.
[6] 周兵营，邵健，何安瑞，等. 热轧高强带钢纵切后侧弯缺陷及其内应力重分布[J]. 机械工程学报，2020，56(18):43-50. ZHOU Bingying，SHAO Jian，HE Anrui，et al. Lateral bending and stress redistribution of high strength steel strip after longitudinal slitting[J]. Journal of Mechanical Engineering，2020，56(18):43-50.
[7] 赵明杰，黄亮，李昌民，等. 300M钢的热变形行为及热锻成形工艺研究现状[J]. 精密成形工程，2020，12(6):16-27. ZHAO Mingjie，HAUNG Liang，LI Changmin，et al. Research status of the hot deformation behaviors and hot forging process of 300M steel[J]. Journal of Netshape Forming Engineering，2020，12(06):16-27.
[8] 刘文权，盈亮，王丹彤，等. 热冲压成形过程细观损伤演化机理研究[J]. 机械工程学报，2016，52(14):31-39. LIU Wenquan，YING Liang，WANG Dantong，et al. Investigation of mesoscopic damage evolution mechanism of high strength steel in hot stamping process[J]. Journal of Mechanical Engineering，2016，52(14):31-39.
[9] ALLAIN S，BOUAZIZ O，CHATEAU J P. Thermally activated dislocation dynamics in austenitic FeMnC steels at low homologous temperature[J]. Scripta Materialia，2010，62(7):500-503.
[10] IMANDOUST A，ZAREI-HANZAKI A，SABET M，et.al. An analysis of the deformation characteristics of a dual phase twinning-induced plasticity steel in warm working temperature regime[J]. Materials & Design，2012，40:556-561.
[11] JUNG I C，DE COOMAN B C. Temperature dependence of the flow stress of Fe-18Mn-0.6C-xAl twinning-induced plasticity steel[J]. Acta Materialia，2013，61(18):6724-6735.
[12] LIANG Z Y，LUO Z C，HUANG M X. Temperature dependence of strengthening mechanisms in a twinning-induced plasticity steel[J]. International Journal of Plasticity，2019，116:192-202.
[13] DANCETTE S，DELANNAY L，RENARD K，et al. Crystal plasticity modeling of texture development and hardening in TWIP steels[J]. Acta Materialia，2012，60(5):2135-2145.
[14] LU X，ZHAO J，WANG Z，et al. Crystal plasticity finite element analysis of gradient nanostructured TWIP steel[J]. International Journal of Plasticity，2020，130:102703.
[15] SUN C Y，GUO N，FU M W，et al. Modeling of slip，twinning and transformation induced plastic deformation for TWIP steel based on crystal plasticity[J]. International Journal of Plasticity，2016，76:186-212.
[16] ZHANG X，SAWAGUCHI T，OGAWA K，et al. Temperature dependence of intersection reactions of e martensite plates in an Fe-30Mn-4Si-2Al TRIP/TWIP steel[J]. Journal of Alloys and Compounds，2013，577: S533-S537.
[17] LIU F，DAN W J，ZHANG W G. Strain hardening model of twinning induced plasticity steel at different temperatures[J]. Materials & Design，2015，65:737-742.
[18] MADIVALA M，SCHWEDT A，WONG S L，et al. Temperature dependent strain hardening and fracture behavior of TWIP steel[J]. International Journal of Plasticity，2018，104:80-103.
[19] DE MADDIS M，RUSSO S P. Plastic flow behavior of twinning induced plasticity steel from low to warm temperatures[J]. Journal of Materials Research and Technology，2020，9(2):1708-1719.
[20] WANG J，LU J，YOU X，et al. In-situ comparison of deformation behavior at 23 ℃ and 650 ℃ of laser direct melting deposited Ti-6Al-4V alloy[J]. Materials Science and Engineering:A，2019，749:48-55.
[21] BOUAZIZ O，GUELTON N. Modelling of TWIP effect on work-hardening[J]. Materials Science and Engineering:A，2001，319-321:246-249.
[22] KHAN R，ALFOZAN A. Modeling of twinning-induced plasticity using crystal plasticity and thermodynamic framework[J]. Acta Mechanica，2019，230(8):2687-2715.
[23] SALEN A A，KALIDINDI S R，SEMIATIN S L. Strain hardening due to deformation twinning in α-titanium: Constitutive relations and crystal-plasticity modeling[J]. Acta Materialia，2005，53(12):3495-3502.
[24] LI Y Z，LUO Z C，LIANG Z Y，et al. Effect of carbon on strain-rate and temperature sensitivity of twinning-induced plasticity steels:Modeling and experiments[J]. Acta Materialia，2019，165:278-293.
[25] LIU X，SUN W K，LIEW K M. Multiscale modeling of crystal plastic deformation of polycrystalline titanium at high temperatures[J]. Computer Methods in Applied Mechanics and Engineering，2018，340:932-955.
[26] 章海明，徐帅，李倩，等. 晶体塑性理论及模拟研究进展[J]. 塑性工程学报，2020，27(5):12-32. ZHANG Haiming，XU Shuai，LI Qian，et al. Progress of crystal plasticity theory and simulations[J]. Journal of Plasticity Engineering，2020，27(5):12-32.
[27] HAN M C，SUN C Y，SHI B，et al. Strain rate and orientation-dependent strain hardening of Mg-9Li-Al using crystal plasticity[J]. Materials Science & Technology，2017，34(4):440-454.
[28] GUTIERREZ-URRURIA I，RAABE D. Multistage strain hardening through dislocation substructure and twinning in a high strength and ductile weight-reduced Fe-Mn-Al-C steel[J]. Acta Materialia，2012，60(16):5791-5802.
[29] SU Z X，LI N，SUN C Y，et al. Strain rate-dependent hardening with dislocation-twin interaction of Fe-Mn-Al-C steel using crystal plasticity[J]. Materials Science and Technology，2019，35(12):1436-1447.
[30] 郭宁. 高锰钢塑性变形机制的晶体塑性建模研究及应用[D]. 北京:北京科技大学，2018. GUO Ning. Crystal plasticity modeling of plastic deformation mechanism for high manganese steel and its application[D]. Beijing:University of Science & Technology Beijing，2018.
[31] PIERCE D T，NOWAG K，MONTAGNE A，et al. Single crystal elastic constants of high-manganese transformation-and twinning-induced plasticity steels determined by a new method utilizing nanoindentation[J]. Materials Science and Engineering:A，2013，578:134-139.
[32] GEBHARDT T，MUSIC D，KOSSMANN D，et al. Elastic properties of fcc Fe-Mn-X (X=Al，Si) alloys studied by theory and experiment[J]. Acta Materialia，2011，59(8):3145-3155.
[33] KALIDINDI S R. Modeling anisotropic strain hardening and deformation textures in low stacking fault energy fcc metals[J]. International Journal of Plasticity，2001，17(6):837-860.
[34] 杨竞，黄杰，孙朝阳，等. 耦合孪生晶体塑性模型硬化参数的灵敏度分析[J]. 工程科学学报，2015，37(8):1076-1083. YANG Jing，HUANG Jie，SUN Chaoyang，et al. Sensitivity analysis of hardening parameters in the crystal plasticity model exhibiting deformation twinning[J]. Chinese Journal of Engineering，2015，37(8):1076-1083.
[35] QUEY R，DAWSON P R，BARBE F. Large-scale 3D random polycrystals for the finite element method: Generation，meshing and remeshing[J]. Computer Methods in Applied Mechanics and Engineering，2011，200(17-20):1729-1745.
[36] 孙朝阳，郭祥如，郭宁，等. 耦合孪生的TWIP钢多晶体塑性变形行为研究[J]. 金属学报，2015，51(12):1507-1515. SUN Chaoyang，GUO Xiangru，GUO Ning，et al. Investigation of plastic deformation behavior on coupling twinning of polycrystal TWIP steel[J]. Acta Metallurgica Sinica，2015，51(12):1507-1515.
[37] SPANNRAFT L，EKH M，LARSSON F，et al. Grain boundary interaction based on gradient crystal inelasticity and decohesion[J]. Computational Materials Science，2020，178:109604.
[38] DING J，SHANG Z，LI J，et al. Microstructure and tensile behavior of nanostructured gradient TWIP steel[J]. Materials Science and Engineering:A，2020，785:139346.

耦合温度效应晶体塑性的TWIP钢变形行为研究

Investigation of Deformation Behavior of TWIP Steel Using Crystal Plasticity Coupling Temperature Effect

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	蒋飞, 赵升吨, 范淑琴, 王可心, 陈超. 剥肋滚压复合工艺及其设备研究[J]. 机械工程学报, 2024, 60(8): 132-142.
[2]	崔学习, 万敏, 吴向东, 关铂镔, 周兵营. 基于应变演化的集中性失稳确定方法[J]. 机械工程学报, 2023, 59(22): 234-244.
[3]	李涛, 黄惟琦, 龙归, 杨思铄, 张建国, 肖峻峰, 许剑锋. 单晶硅的激光抛光表面形貌演化[J]. 机械工程学报, 2023, 59(21): 52-64.
[4]	杨博文, 高强, 王硕, 霍军周. 基于面面接触结构的高温微动疲劳寿命预测研究[J]. 机械工程学报, 2023, 59(18): 165-174.
[5]	冀寒松, 宋清华, 杜宜聪, 刘战强. Inconel-718微构件晶粒尺度伪随机建模与仿真[J]. 机械工程学报, 2023, 59(17): 232-240.
[6]	郑战光, 覃里杜, 谢昌吉, 潘淑琴, 孙腾. 晶体塑性疲劳指示因子研究方法综述[J]. 机械工程学报, 2022, 58(8): 105-116.
[7]	韩建超, 姚昊明, 贾燚, 谢广明, 王涛. 新型三相TiAl合金高温塑性变形行为及流动软化研究[J]. 机械工程学报, 2022, 58(16): 77-88.
[8]	王姝予, 宋世杰, 陆晓翀, 阚前华, 康国政, 张旭. CrMnFeCoNi高熵合金拉伸断裂的晶体塑性有限元模拟[J]. 机械工程学报, 2021, 57(22): 43-51.
[9]	郭晓曦, 李恒, 冯振勇, 张铎. 铝合金管弯曲成形表面粗化宏细观耦合建模仿真[J]. 机械工程学报, 2021, 57(22): 209-217.
[10]	李银银, 蒋玮. 基于纳米压痕的激光修复层晶体材料常数反演方法[J]. 机械工程学报, 2021, 57(2): 97-104.
[11]	孙李刚, 凌超, 陈浩, 李东风. 结构完整性分析中的多尺度力学方法[J]. 机械工程学报, 2021, 57(16): 106-121.
[12]	孙莉, 郭素娟, 苑光健, 陈杨熙, 张显程, 涂善东. 宏/微观循环本构模型及其在工程结构中的应用[J]. 机械工程学报, 2021, 57(16): 198-217.
[13]	安琪, 索双富, 林福严, 白玉柱, 耿海旭, 时剑文. 平面磨削粗糙表面的微观接触模型[J]. 机械工程学报, 2020, 56(7): 240-248.
[14]	胡志力, 范新欣, 华林. 高强铝合金FSW拼焊板变形规律与成形技术[J]. 机械工程学报, 2020, 56(6): 206-212.
[15]	陈翔, 陈伟, 禄盛, 金晓清, 马文生, 赵洋. NiTiNb记忆合金热力学性能的试验及其唯象本构模型[J]. 机械工程学报, 2020, 56(4): 65-75.