基于非线性动力学模型高速球轴承摩擦力矩研究

doi:10.3901/JME.2022.17.181

机械工程学报 ›› 2022, Vol. 58 ›› Issue (17): 181-190.doi: 10.3901/JME.2022.17.181

扫码分享

基于非线性动力学模型高速球轴承摩擦力矩研究

常红阳^1,2, 邓松^1,2,3, 钱东升⁴, 华林^1,2, 王丰^1,2

1. 武汉理工大学现代汽车零部件技术湖北省重点实验室武汉 430070;
2. 武汉理工大学汽车零部件技术湖北省协同创新中心武汉 430070;
3. 洛阳轴承研究所有限公司洛阳 471039;
4. 武汉理工大学湖北省材料绿色精密成形工程技术研究中心武汉 430070

收稿日期:2021-04-02 修回日期:2022-05-08 发布日期:2022-11-07
作者简介:常红阳,男,1997年出生。主要研究方向为轴承设计及理论。E-mail:1982411341@qq.com;王丰,男,1992年出生,博士,博士后。主要研究方向为轴承动力学及设计理论。E-mail:wangfengwhut@163.com

Study on Friction Moments of High Speed Ball Bearings Based on Nonlinear Dynamic Model

CHANG Hongyang^1,2, DENG Song^1,2,3, QIAN Dongsheng⁴, HUA Lin^1,2, WANG Feng^1,2

1. Hubei Key Laboratory of Advanced Technology for Automotive Components, Wuhan University of Technology, Wuhan 430070;
2. Hubei Collaborative Innovation Center for Automotive Components Technology, Wuhan University of Technology, Wuhan 430070;
3. Luoyang Bearing Research Institute Co., Ltd., Luoyang 471039;
4. Hubei Engineering Research Center for Green Precision Material Forming, Wuhan University of Technology, Wuhan 430070

Received:2021-04-02 Revised:2022-05-08 Published:2022-11-07
Contact: 湖北省重点研发计划(2021BAA019)和国家重点研发计划(2019YFB2004304)资助项目。

摘要/Abstract

摘要： 针对钢球滚动周期内钢球滑滚比实时变化，采用粗糙摩擦系数与滑滚比关系方程实时修正钢球与滚道的摩擦系数。针对高速轻载时钢球粗糙摩擦牵引和润滑牵引显著增大且赫兹接触力明显减小，建立考虑钢球摩擦牵引和润滑牵引的高速球轴承非线性动力学模型。基于该模型结合经典的六类摩擦力矩经验公式计算轴承总摩擦力矩。根据不同载荷下钢球角速度和轴承摩擦力矩证明了该模型是有效的，进而研究了轴承高低速、轻重载和初始接触角对轴承摩擦力矩的影响规律，揭示了不同工况和初始接触角时六类摩擦力矩的影响权重和诱因。分析结果表明：在轻重载条件下，低速时，差动滑动摩擦力矩主要影响总摩擦力矩，高速时，润滑黏度摩擦力矩主要影响总摩擦力矩。在较大径轴向载荷作用下，高速轴承产生较大的自旋摩擦力矩，其次是润滑黏度摩擦力矩。

关键词: 高速球轴承, 非线性动力学模型, 摩擦力矩, 粗糙摩擦牵引, 润滑牵引

Abstract: In view of the real-timely variation of slide-to-roll ratio of balls, the relation of asperity friction coefficient with the slide-to-roll ratio is adopted to adjust the asperity friction between balls and raceways. At high speeds and light loads, asperity friction traction and lubricant traction of balls are intensified significantly and the Hertz contact force is decreased markedly, which is emphasized to develop a nonlinear dynamic model of high speed ball bearings. Then, combining this model with these classic empirical formulas of six kinds of friction moments to calculate the total friction moment. This model is proved to be effective according to the angular velocity of steel ball and the friction moment of bearing under different loads. Subsequently, the effects of high and low speeds, light and heavy loads, and initial contact angles on friction moments are analyzed, and the influence weights and inducements of six kinds of friction moments under different working conditions and initial contact angles are revealed. The results show that under the condition of light and heavy loads, differential sliding friction moment mainly affects the total friction moment at low speeds, while viscous friction moment mainly contributes to the total friction moment at high speeds. Moreover, under combined loads, spinning friction crucially effects the total friction moment for high speed bearings, and the next is viscous friction moment.

Key words: high speed ball bearings, nonlinear dynamic model, friction moments, asperity friction traction, lubricant traction

中图分类号:

TH132

常红阳, 邓松, 钱东升, 华林, 王丰. 基于非线性动力学模型高速球轴承摩擦力矩研究[J]. 机械工程学报, 2022, 58(17): 181-190.

CHANG Hongyang, DENG Song, QIAN Dongsheng, HUA Lin, WANG Feng. Study on Friction Moments of High Speed Ball Bearings Based on Nonlinear Dynamic Model[J]. Journal of Mechanical Engineering, 2022, 58(17): 181-190.

导出引用管理器 EndNote|Reference Manager|ProCite|BibTeX|RefWorks

链接本文: http://www.cjmenet.com.cn/CN/10.3901/JME.2022.17.181

http://www.cjmenet.com.cn/CN/Y2022/V58/I17/181

参考文献

[1] BRECHER C，HASSIS A，ROSSAINT J. Cage friction in high-speed spindle bearings[J]. Tribology Transactions，2014，57：77-85.
[2] GHANBARI A，KHANMOHAMADI S. A new test rig for frictional torque measurement in ball bearings[J]. WSEAS Transactions on Systems，2006，5(9)： 2172-2177.
[3] TOWNSEND D P，ALLEN C W，ZARETSKY E V. Study of ball bearing torque under elasto-hydrodynamic lubrication[J]. Journal of Lubrication Technology，1974, 96(4)：561-71.
[4] TIAN Shenli， CHEN Xiaoan，CHEN Tianchi，et al. Experimental analysis and modeling of the effects of oil–air lubrication parameters on bearings friction loss of high-speed motorized spindle[J]. Tribology Transactions, 2019，62(3)：524-534.
[5] 宁峰平，陈然，夭银银，等. 预紧力与装配偏差对航天轴承摩擦力矩的影响研究[J]. 兵工学报，2018, 39(7)：191-197. NING Fengping，CHEN Ran，YAO Yinyin, et al. Influences of preload and assembly deviation on friction torque of aerospace bearing[J]. Acta Armamentarii, 2018，39(7)：191-197.
[6] 邓四二，华显伟，张文虎. 陀螺角接触球轴承摩擦力矩波动性分析[J]. 航空动力学报，2018，33(7)： 1713-1724. DENG Sier，HUA Xianwei，ZHANG Wenhu. Analysis on friction torque fluctuation of angular contact ball bearing in gyro motor[J]. Journal of Aerospace Power，2018，33(7)：1713-1724.
[7] 邓四二，李兴林，汪久根，等. 角接触球轴承摩擦力矩特性研究[J]. 机械工程学报，2011，47(5)：118-124. DENG Sier，LI Xinglin，WANG Jiugen， et al. Frictional torque characteristic of angular contact ball bearings[J]. Journal of Mechanical Engineering，2011，47(5)：114-120.
[8] LI Junning，CHEN Wei. Design and implementation of analysis system for skid damage of high speed rolling bearing based on VB and VC[J]. Lubrication Engineering，2011，36(1)：4-8.
[9] BIZARRE L，NONATO F，CAVALCA K L. Formulation of five degrees of freedom ball bearing model accounting for the nonlinear stiffness and damping of elastohydrodynamic point contacts[J]. Mechanism and Machine Theory，2018，124：179-196.
[10] HAN Qinkai，CHU Fulei. Nonlinear dynamic model for skidding behavior of angular contact ball bearings[J]. Journal of Sound and Vibration，2015，354：219-235.
[11] GAO S，CHATTERTON S，NALDI L，et al. Ball bearing skidding and over-skidding in large-scale angular contact ball bearings：Nonlinear dynamic model with thermal effects and experimental results[J]. Mechanical Systems and Signal Processing，2021，147：107120.
[12] 邓四二，盛明杰，邓凯文，等. 双列调心滚子轴承摩擦力矩的特性[J]. 航空动力学报，2017，32(7)：1666-1675. DENG Sier，SHENG Mingjie，DENG Kaiwen，et al. Friction torque of double-row spherical roller bearings[J]. Journal of Aerospace Power，2017，32(7)：1666-1675.
[13] LIU Jing，LI Xinbin，DING Shizhao，et al. A time-varying friction moment calculation method of an angular contact ball bearing with the waviness error[J]. Mechanism and Machine Theory，2020，148：103799.
[14] 邓四二，贾群义. 滚动轴承设计原理[M]. 北京：中国标准出版社，2014. DENG Sier，JIA Qunyi. Design priciple of rolling bearing[M]. Beijing：China Standards Press，2014.
[15] TONG V C，HONG S W. Improved formulation for running torque in angular contact ball bearings[J]. International Journal of Precision Engineering and Manufacturing，2018，19(1)：47-56.
[16] HARRIS T A，KOTZALAS M N. Advanced concepts of bearing technology[M]. Boca Raton：Taylor & Francis， 2007.
[17] MASJEDI M，KHONSARI M M. Theoretical and experimental investigation of traction coefﬁcient in line-contact EHL of rough surfaces[J]. Tribology International，2014，70：179-89.
[18] WANG Y，WANG W，ZHANG S，et al. Investigation of skidding in angular contact ball bearings under high speed[J]. Tribology International，2015，92：404-417.
[19] NONATO F X，CAVALCA K L. On the non-linear dynamic behavior of elastohydrodynamic lubricated point contact[J]. Journal of Sound and Vibration，2010，329(22)：4656-4671.
[20] PASDARI M，GENTLE C R. Effect of lubricant starvation on the minimum load condition in a thrust-loaded ball bearing[J]. ASLE Transactions，1987，30 (3)：355-359.
[21] HAO Lina，DENG Song，QIAN Dongsheng，et al. Accurate prediction method of initial value of high-speed ball bearing model and gyroscopic torque analysis[J]. Journal of Mechanical Science and Technology，2020，34(9)：3745-3755.

基于非线性动力学模型高速球轴承摩擦力矩研究

Study on Friction Moments of High Speed Ball Bearings Based on Nonlinear Dynamic Model

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	郭万金, 利乾辉, 徐明坤, 侯旭栋, 刘孝恒, 曹雏清, 赵立军. 高抗干扰性的无力传感器工业机器人外力估计方法[J]. 机械工程学报, 2026, 62(3): 366-383.
[2]	栾雯霖, 王园丁, 王浩明, 刘艳, 李祥龙, 徐方程. 螺旋槽结构参数对新型混合式螺旋槽气体止推箔片轴承静态特性影响的理论分析[J]. 机械工程学报, 2025, 61(9): 358-371.
[3]	赵礼辉, 王震, 刘天胤, 刘东俭, 翁硕, 张东东. 随机载荷下电驱动系统高速球轴承疲劳寿命预测方法研究[J]. 机械工程学报, 2025, 61(8): 214-227.
[4]	包倩倩, 周俊杰, 荆崇波, 廖文博, 杜善霄, 张祝. 液压变压器自由转子的摩擦力矩模型与试验验证[J]. 机械工程学报, 2025, 61(6): 308-315.
[5]	赵佳佳, 宋现春, 姜洪奎, 林明星, 宋丽伟. 考虑热弹流润滑作用的滚珠丝杠副摩擦力矩建模与分析[J]. 机械工程学报, 2023, 59(3): 176-188.
[6]	侯正航, 何卫平, 王淑侠, 胡余彭, 肖一帆. 基于数字孪生的弧齿型导引头伺服机构动态装调技术研究[J]. 机械工程学报, 2023, 59(22): 433-443.
[7]	樊赛生, 郭峰, 荆兆刚, 栗心明, 刘海超, POLL G. 硬脂酸吸附对轴承限量供油润滑影响[J]. 机械工程学报, 2023, 59(15): 197-203.
[8]	邱烁现, 徐方程. 平箔片凹陷对止推箔片轴承性能影响试验研究[J]. 机械工程学报, 2022, 58(15): 226-232,242.
[9]	徐方程, 侯留凯, 吴斌, 何波. 楔形入口高度对气体止推箔片轴承性能仿真和试验研究[J]. 机械工程学报, 2021, 57(9): 51-60.
[10]	姜仁华, 刘闯, 宁银行. 雷达伺服系统的自适应摩擦力矩补偿控制策略[J]. 机械工程学报, 2019, 55(18): 187-195.
[11]	吴伟, 尚建忠, 罗自荣, 曹玉君, 于乃辉. 面向弧形框架式导引头伺服机构的摩擦力矩测量系统及精密装配工艺[J]. 机械工程学报, 2018, 54(11): 77-84.
[12]	马子魁, 陈文华. 基于滚动蠕滑理论的球轴承摩擦力矩计算方法[J]. 机械工程学报, 2017, 53(22): 219-224.
[13]	胡华君, 潘博, 孙京. 航天器驱动机构轴系摩擦力矩建模与分析研究[J]. 机械工程学报, 2017, 53(11): 75-80.
[14]	王亚泰, 闫柯, 朱永生, 洪军, 张优云. 保持架不同引导方式下角接触球轴承腔内气相流动分析^*[J]. 机械工程学报, 2017, 53(1): 72-78.
[15]	王恒, 张俊杰, 王永泉, 陈花玲. 考虑反向器影响的滚珠丝杠副摩擦力矩计算模型[J]. 机械工程学报, 2016, 52(7): 97-103.