现代产品主动再制造理论与设计方法

doi:10.3901/JME.2016.07.133

机械工程学报 ›› 2016, Vol. 52 ›› Issue (7): 133-141.doi: 10.3901/JME.2016.07.133

扫码分享

现代产品主动再制造理论与设计方法

宋守许, 刘明, 刘光复, 柯庆镝

合肥工业大学机械与汽车工程学院合肥 230009

出版日期:2016-04-05 发布日期:2016-04-05
作者简介:宋守许,男,1964年出生,博士,教授。主要研究方向为绿色设计与绿色制造、再制造工程、产品再资源化。E-mail：shouxus@163.com;刘明(通信作者),男,1989年出生。主要研究方向为机电产品绿色设计与绿色制造。E-mail：lm200809@sina.com;刘光复,男,1945年出生,教授,博士研究生导师。主要研究方向为机电产品绿色设计与绿色制造、现代集成制造技术。E-mail：gfliu@hfut.deu.cn;柯庆镝,男,1984年出生,博士。主要研究方向为再制造工程、节能设计。E-mail：qri1001@163.com
基金资助:
国家重点基础研究发展计划(973计划,2011CB013406)和国家自然科学基金(51375133,51305119)资助项目

Theories and Design Methods for Proactive Remanufacturing of Modern Products

SONG Shouxu, LIU Ming, LIU Guangfu, KE Qingdi

School of Machinery and Automobile Engineering, Hefei University of Technology, Hefei 230009

Online:2016-04-05 Published:2016-04-05

摘要/Abstract

摘要： 再制造是再循环的最佳形式,但被动再制造毛坯数量和质量上的不确定阻碍了再制造工程的产业化。针对目前研究中仍存在的问题,提出主动再制造的概念,在分析产品再制造与其寿命周期的关系基础上,阐述主动再制造理论,介绍主动再制造中的相关概念,归纳主动再制造的主要特征。同时为了更加合理地实现主动再制造,针对产品中零部件间的关系,进行主动再制造设计的探讨,建立主动再制造设计理论与设计方法框架,阐述主动再制造设计的基础理论和基本流程,并且对应于主动再制造设计中的产品级设计、零部件级设计和结构级设计分别提出了寿命匹配、结构功能梯度和冗余强度,并进行了综合分析。以发动机曲轴-连杆系统为例,进行了主动再制造设计,结果表明,提出的设计理论与设计方法是有效、可行的。

关键词: 结构功能梯度, 冗余强度, 寿命匹配, 主动再制造

Abstract: Remanufacturing is the ultimate form of recycling. However, the uncertainties in quality and quantity of cores in reactive remanufacturing hinder the industrialization of remanufacturing. To meet with the issues, the concept of proactive remanufacturing is put forward. Based on the relationship between remanufacturing and the lifecycle of products, theories of proactive remanufacturing are expounded. Besides, the relevant concepts in proactive remanufacturing are presented, and the principal characters of proactive remanufacturing are concluded. Then, in order to realize proactive remanufacturing more reasonably, design for proactive remanufacturing, which aims at optimizing the relationship of components, is discussed. The structure of design theories and methods for proactive remanufacturing is established. The fundamental theories and basic process of design for proactive remanufacturing are presented. Meanwhile, the concepts of life matching, structural functionally gradient and residual strength, which respectively correspond to the design of product level, component level and structure level, are proposed. Finally, designs for proactive remanufacturing are demonstrated by taking the system of crankshaft and connecting rod for an example. The results show that, the design theories and methods are valid and feasible.

Key words: life matching, proactive remanufacturing, residual strength, structural functionally gradient

中图分类号:

TH122

宋守许, 刘明, 刘光复, 柯庆镝. 现代产品主动再制造理论与设计方法[J]. 机械工程学报, 2016, 52(7): 133-141.

SONG Shouxu, LIU Ming, LIU Guangfu, KE Qingdi. Theories and Design Methods for Proactive Remanufacturing of Modern Products[J]. Journal of Mechanical Engineering, 2016, 52(7): 133-141.

参考文献

[1] IJOMAH W L,CHILDE S J. A model of the operations concerned in remanufacture [J]. International Journal of Production Research,2007,45(24)：5857-5880.
[2] 朱胜,姚巨坤. 再制造设计理论及应用[M]. 北京：机械工业出版社,2009.
ZHU Sheng,YAO Jukun. Design theories and applications of remanufacturing [M]. Beijing：China Machine Press,2009.
[3] STEINHILPER R. Remanufacturing—the ultimate form of recycling [M]. Stuttgart：Fraunhofer IRB Verlag,1998.
[4] TEUNTER R H,FLAPPER S D P. Optimal core acquisition and remanufacturing policies under uncertain core quality fractions [J]. European Journal of Operational Research,2011,210(2)：241-248.
[5] SOUZA G C,KETZENBERG M,GUIDE V D R. Capacitated remanufacturing with service level constraints [J]. Production and Operations Management,2002,11(2)：231-248.
[6] FERGUSON M,GUIDE V D R,KOCA E,et al. The value of quality grading in remanufacturing [J]. Production and Operations Management,2009,18(3)：300-314.
[7] GUIDE V D R. Production planning and control for remanufacturing：Industry practice and research needs [J]. Journal of Operations Management,2000,18(4)：467-483.
[8] MUKHOPADKYAY S K,MA H. Joint procurement and production decisions in remanufacturing under quality and demand uncertainty [J]. International Journal of Production Economics,2009,120(1)：5-17.
[9] GALBRETH M R,BLACKBURN J D. Optimal acquisition quantities in remanufacturing with condition uncertainty [J]. Production and Operations Management,2010,19(1)：61-69.
[10] 杨继荣,段广洪,向东．面向再制造工程的绿色模块化设计方法研究[J]. 中国表面工程,2006,19(5)：67-70.
YANG Jirong,DUAN Guanghong,XIANG Dong. The research on the method of the green modular design for remanufacture engineering [J]. China Surface Engineering,2006,19(5)：67-70．
[11] CHARTER M,GRAY C. Remanufacturing and product design [J]. International Journal of Product Development,2008,6(3-4)：375-392.
[12] HATCHER G D,IJOMAH W L,WINDMILL J F C. Integrating design for remanufacture into the design process：The operational factors [J]. Journal of Cleaner Production,2012,39：200-208.
[13] SUNDIN E,LINDAHL M. Rethinking product design for remanufacturing to facilitate integrated product service offerings[C]// 2008 IEEE International Symposium on Electronics and the Environment,May 19-21,2008,San Francisco,CA,USA. New York：IEEE,2008：263-268.
[14] PIGOSSO D C A,ZANETTE E T,FILHO A G,et al. Ecodesign methods focused on remanufacturing [J]. Journal of Cleaner Production,2010,18 (1)：21-31.
[15] ZWOLINSKI P,BRISSAUD D. Remanufacturing strategies to support product design and redesign [J]. Journal of Engineering Design,2008,19 (4)：321-335.
[16] 宋守许,刘明,柯庆镝,等. 基于强度冗余的零部件再制造优化设计方法[J]. 机械工程学报,2013,49(9)：121-127.
SONG Shouxu,LIU Ming,KE Qingdi,et al. Components optimization design for remanufacturing based on residual strength [J]. Journal of Mechanical Engineering,2013,49(9)：121-127.
[17] 刘艺. 发动机连杆剩余疲劳寿命预测及再制造可行性研究[D]. 济南：山东大学,2010.
LIU Yi. Prediction for residual fatigue life of connecting rod and research on its remanufacturability [D]. Jinan：Shandong University,2010.

现代产品主动再制造理论与设计方法

Theories and Design Methods for Proactive Remanufacturing of Modern Products

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 5

编辑推荐

Metrics

本文评价

[1]	宋守许, 郁炯, 蔚辰, 张志旭. 考虑多辊修磨关系的轧辊主动再制造设计方法[J]. 机械工程学报, 2022, 58(13): 203-212.
[2]	柯庆镝, 王辉, 宋守许, 刘光复. 产品全生命周期主动再制造时域抉择方法[J]. 机械工程学报, 2017, 53(11): 134-143.
[3]	宋守许, 汪伟, 柯庆镝. 基于结构功能衍生系数的主动再制造设计[J]. 机械工程学报, 2017, 53(11): 175-183.
[4]	鲍宏, 刘志峰, 胡迪, 柯庆镝, 张城. 应用TRIZ的主动再制造绿色创新设计研究[J]. 机械工程学报, 2016, 52(5): 33-39.
[5]	刘光复;刘涛;柯庆镝;宋守许;周丹. 基于博弈论及神经网络的主动再制造时间区域抉择方法研究[J]. , 2013, 49(7): 29-35.