超临界流体辅助微孔发泡注塑技术及其熔体发泡行为

doi:10.3901/JME.2018.18.042

机械工程学报 ›› 2018, Vol. 54 ›› Issue (18): 42-48.doi: 10.3901/JME.2018.18.042

超临界流体辅助微孔发泡注塑技术及其熔体发泡行为

董桂伟, 赵国群, 管延锦, 王桂龙, 侯俊吉, 吴昊

山东大学材料液固结构演变与加工教育部重点实验室济南 250061

收稿日期:2018-01-21 修回日期:2018-04-24 出版日期:2018-09-20 发布日期:2018-09-20
作者简介:董桂伟,男,1981年出生,博士研究生。主要研究方向为微孔塑料成型工艺与技术。E-mail:gwdong@sdu.edu.cn;赵国群,男1962年出生,教授,博士研究生导师。主要研究方向为塑性成形理论、数值模拟方法、模具CAD/CAM/CAE。E-mail:zhaogq@sdu.edu.cn
基金资助:
山东省优秀创新团队（2012-136）、中国博士后科学基金（2018M632671）和材料成形与模具技术国家重点试验室开放课题研究基金（P2018-002）资助项目。

Supercritical Fluid Assisted Microcellular Injection Molding and the Melt Foaming Behaviors

DONG Guiwei, ZHAO Guoqun, GUAN Yanjin, WANG Guilong, HOU Junji, WU Hao

Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials of Ministry of Education, Shandong University, Jinan 250061

Received:2018-01-21 Revised:2018-04-24 Online:2018-09-20 Published:2018-09-20

摘要/Abstract

摘要： 开发一种超临界流体辅助微孔发泡注塑新技术，研制相应的超临界流体发生与计量控制技术系统，构建超临界流体辅助微孔发泡注塑试验线，并对超临界流体辅助微孔发泡注塑熔体的发泡行为进行研究。结果表明，超临界流体辅助微孔发泡注塑熔体的发泡过程包括“填充过程中发泡”和“填充结束后发泡”两个过程，分别对应成型产品内部的变形椭球形泡孔和规则球形泡孔两种不同的泡孔结构形态，而熔体“填充过程中发泡”形成的泡孔，受熔体剪切和喷泉流动行为的影响而发生变形，并在熔体流动前锋处破裂、涌出，与冷的模具表面接触后冷凝遗留在产品表面，形成表面气泡痕。所揭示的发泡演变过程和缺陷产生机理对微孔发泡注塑工艺原理和质量控制有较高的参考意义和工程应用价值。

关键词: 超临界流体, 发泡行为, 熔体, 微孔发泡注塑技术

Abstract: A new supercritical fluid assisted microcellular injection molding technique and the corresponding supercritical fluid generation, measurement and monitoring systems are developed. The supercritical fluid assisted microcellular injection molding test line is constructed. The melt foaming behaviors in supercritical fluid assisted microcellular injection molding are investigated. The results show that the melt foaming process in supercritical fluid assisted microcellular injection molding contains two processes:"foam during injection" and "foam after injection", respectively corresponding to the two different cell morphologies of distorted ellipsoidal cells and the regular spherical cells in the microcellular injection molded parts. The cells formed in "foam during injection" process are stretched by the shear flow and fountain flow behaviors, then broken, pushed out and turned over to both sides of the melt flow front, and finally contacted with the cold mold cavity surface and solidified to form surface bubble marks on the molded parts. The revealed foaming processes and defects generation mechanism have higher reference significance and engineering application value for technological principle and quality control of microcellular injection molding.

Key words: foaming behavior, melt, microcellular injection molding, supercritical fluid

中图分类号:

TQ328

董桂伟, 赵国群, 管延锦, 王桂龙, 侯俊吉, 吴昊. 超临界流体辅助微孔发泡注塑技术及其熔体发泡行为[J]. 机械工程学报, 2018, 54(18): 42-48.

DONG Guiwei, ZHAO Guoqun, GUAN Yanjin, WANG Guilong, HOU Junji, WU Hao. Supercritical Fluid Assisted Microcellular Injection Molding and the Melt Foaming Behaviors[J]. Journal of Mechanical Engineering, 2018, 54(18): 42-48.

参考文献

[1] MARTINI J E,WALDMAN F A,SUH N P. The production and analysis of microcellular thermoplastic foam[J]. SPEANTEC Tech Papers,1982,28:674-676.
[2] AMELI A,JAHANI D,NOFAR M,et al. Development of high void fraction polylactide composite foams using injection molding:Mechanical and thermal insulation properties[J]. Composites Science & Technology,2014,90(2):88-95.
[3] MI H Y,JING X,SALICK M R,et al. Fabrication of thermoplastic polyurethane tissue engineering scaffoldby combining microcellular injection molding and particle leaching[J]. Journal of Materials Research,2014,29(8):911-922.
[4] LIVI S,LINS L C,SAR G,et al. Supercritical CO₂-Ionic liquids:A successful wedding to prepare biopolymer foams[J]. Acs Sustainable Chemistry & Engineering,2016,4(2):461-470.
[5] MILLER D,KUMAR V. Microcellular extrusion of PLA utilizing solid-state nucleation in the gas-saturated pellet extrusion process[J]. Journal of Applied Polymer Science,2013,127(3):1967-1973.
[6] DING W D,JAHANI D,CHANG E,et al. Development of PLA/cellulosic fiber composite foams using injection molding:crystallization and foaming behaviors[J]. Composites Part A-Applied Science and Manufacturing,2016,83:130-139.
[7] YUSA A,YAMAMOTO S,GOTO H,et al. A new microcellular foam injection-molding technology using non-supercritical fluid physical blowing agents[J]. Polymer Engineering and Science,2017,57(1):105-113.
[8] XU J Y. Microcellular Injection molding[M]. New Jersey:Wiley Series on Polymer Engineering and Technology,2010.
[9] TURNG L S,KHARBAS H. Development of a hybrid solid-microcellular co-injection molding process[J]. International Polymer Processing,2004,19(1):77-86.
[10] YOON J D,HONG S K,KIM J H,et al. A mold surface treatment for improving surface finish of injection molded microcellular parts[J]. Cellular Polymers,2004,23(1):39-47.
[11] CHEN S C,LIN Y W,CHIEN R D,et al. Variable mold temperature to improve surface quality of microcellular injection molded parts using induction heating technology[J]. Advances in Polymer Technology,2008,27(4):224-232.
[12] CHEN S C,HSU P S,HWANG S S. The effects of gas counter pressure and mold temperature variation on the surface quality and morphology of the microcellular polystyrene foams[J]. Journal of Applied Polymer Science,2013,127(6):4769-4776.
[13] 李帅,赵国群,管延锦,等. 模具型腔气体压力对微发泡注塑件表面质量的影响[J]. 机械工程学报,2015,51(10):79-85. LI Shuai,ZHAO Guoqun,GUAN Yanjin,et al. Influence of mold cavity gas pressure on the surface quality of a microcellular injection molding part[J]. Journal of Mechanical Engineering,2015,51(10):79-85.
[14] HOU J J,ZHAO G Q,WANG G L,et al. A novel gas-assisted microcellular injection molding method for preparing lightweight foams with superior surface appearance and enhanced mechanical performance[J]. Materials & Design,2017,127(5):115-125.
[15] ZHAI M,XIE Y. Investigation of the effect of process conditions on cell size of microcellular injection molded part[J]. Kgk-Kautschuk Gummi Kunststoffe,2010,63(3):85-88.
[16] GOMEZ-GOMEZ J F,ARENCON D,SANCHEZ-SOTO M A,et al. Influence of the injection moulding parameters on the microstructure and thermal properties of microcellular polyethylene terephthalate glycol foams[J]. Advances in Polymer Technology,2013,49(1):47-63.
[17] LI K,CUI Z X,SUN X F,et al. Effects of nanoclay on the morphology and physical properties of solid and microcellular injection molded polyactide/poly(butylenes adipate-co-terephthalate) (PLA/PBAT) nanocomposites and blends[J]. Journal of Biobased Materials and Bioenergy,2011,5(4):442-451.
[18] KUBOKE T. Mechanical properties and foaming behavior of injection molded cellulose fiber reinforced polypropylene composite foams[J]. Journal of Cellular Plastics,2014,50(2):129-143.

超临界流体辅助微孔发泡注塑技术及其熔体发泡行为

Supercritical Fluid Assisted Microcellular Injection Molding and the Melt Foaming Behaviors

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 10

编辑推荐

Metrics

本文评价

[1]	于同敏, 武永强, 王敏杰. 超声外场对微通道中熔体黏性耗散效应的影响[J]. 机械工程学报, 2015, 51(20): 79-85.
[2]	孔繁余;何玉洋;张慧;夏斌;谭林伟. 熔体齿轮泵热特性分析[J]. , 2014, 50(6): 150-155.
[3]	杨晓东;李倩;申长雨. 基于黄金分割法的聚合物熔体黏度模型数据拟合[J]. , 2014, 50(2): 70-76.
[4]	刘东雷;曹文华;辛勇. 注射成型聚合物充模取向应力场模型化理论研究：考虑熔体的可压缩性[J]. , 2014, 50(12): 75-82.
[5]	李大勇;肖鹏;马旭梁;王利华. 铝镁合金熔体氢含量快速定量检测技术研究进展[J]. , 2013, 49(20): 36-41.
[6]	陈佳佳;瞿金平;刘环裕;张桂珍;谭斌. 叶片熔体输运过程拉伸形变速率的研究[J]. , 2013, 49(14): 74-79.
[7]	李凌丰;茅旭飞;管灵波;张振然. 螺槽内塑料熔体传热及温度的数值模拟[J]. , 2013, 49(14): 23-30.
[8]	王敏杰;田慧卿;赵丹阳. 聚合物熔体微尺度剪切黏度测量方法与黏度模型[J]. , 2012, 48(16): 21-29.
[9]	徐斌;王敏杰;于同敏;赵丹阳. 微尺度效应下的聚合物熔体粘度理论及试验[J]. , 2010, 46(19): 125-132.
[10]	徐斌;于同敏;王敏杰;赵丹阳. 微尺度聚合物熔体粘性耗散效应对流变行为的影响[J]. , 2010, 46(14): 47-52.