• CN:11-2187/TH
  • ISSN:0577-6686

机械工程学报 ›› 2017, Vol. 53 ›› Issue (1): 174-179.doi: 10.3901/JME.2017.01.174

• 数字化设计与制造 • 上一篇    下一篇

热缩刀杆装夹温度的影响因素*

周后明, 刘博, 张高峰, 周友行, 彭锐涛   

  1. 湘潭大学机械工程学院 湘潭 411105
  • 出版日期:2017-01-05 发布日期:2017-01-05
  • 作者简介:周后明(通信作者),男, 1970年出生,博士,副教授。主要研究方向为高速加工技术及其工具。E-mail:zhouhouming@xtu.edu.cn
  • 基金资助:
    * 国家自然科学基金(51375418,51375419,51275436)、湖南省自然科学基金(12JJ8015、13JJ8007)、湖南省高校创新平台开放基金(13K040)、深圳市科技计划(JCYJ20160415114050831)资助项目; 20151211收到初稿,20160909收到修改稿;

The Influence Factors of Shrink-fit Tool Holder Clamping Temperature

ZHOU Houming, LIU Bo, ZHANG Gaofeng, ZHOU Youhang, PENG Ruitao   

  1. School of Mechanical Engineering, Xiangtan University, Xiangtan 411105
  • Online:2017-01-05 Published:2017-01-05

摘要:

为得到热缩刀杆与刀具配合公差与其最小装夹温度之间的精确关系,对影响刀杆接触面最小热位移差值的感应加热长度、热缩刀杆壁厚、锥角、配合长度、内径等因素进行了研究。采用ANSYS参数化设计语言,构建具有过盈特征的刀杆与刀具配合的参数化有限元模型,通过试验验证了模型的可靠性。通过获取热缩刀杆接触面的位移分布,结合刀杆与刀具接触状态的表征方法对接触面上最小热位移差值进行了计算。计算结果表明,配合面最小热位移差值随着热缩刀杆壁厚、配合长度、锥角的增加而减小,随着内径的增大而增大,且适当增大感应加热长度也有利于刀具的装夹。最终建立了配合公差所对应的过盈量?与最小装夹温度T之间的计算关系式,对刀具在热缩刀杆中的装夹及刀杆的结构设计提供理论指导。

关键词: 参数化模型, 配合公差, 热缩刀杆, 装夹温度

Abstract: A research of the length of induction heating, shrink-fit tool holder thickness, cone angle, length of fit and inner diameter etc. for the influence of minimum contact surface displacement difference with the holder to find the exact relationship between tolerance and minimum clamping temperature. The interference characteristics of holder and tool with the parameterized finite element model by ANSYS parametric design language and verified by experiment for the reliability of the model is built. The minimum displacement difference is calculated by getting the displacement distribution of the contact surface on tool holder with the combination of characterization methods between holder and tool contact status. Calculations indicated that the minimum thermal displacement difference of the fitting surface will decrease with the increase of holder thickness, length of fit, cone angle; it will increase with the inner diameter increasing, and it is good for the clamping if increase the length of induction heating appropriately. Finally, we established the calculating formula between interferencef and the minimum clamping temperature T, it has a practical guiding significance for the clamping process of the cutting tool and the design of the holder.

 

Key words: fitting tolerance, parameterized model, shrink-fit tool holder, clamping temperature