• CN:11-2187/TH
  • ISSN:0577-6686

机械工程学报 ›› 2026, Vol. 62 ›› Issue (17): 413-429.doi: 10.3901/JME.260549

• 数字化设计与制造 • 上一篇    

扫码分享

基于改进SOTA法的飞机四连杆舱门三维公差分析

杨睿, 杨林凯, 韦磊, 孙士勇   

  1. 大连理工大学机械工程学院 大连 116024
  • 收稿日期:2025-04-01 修回日期:2026-03-25 发布日期:2026-11-20
  • 作者简介:杨睿,男,1974年出生,博士,教授,博士研究生导师。主要研究方向为复杂装备的非线性三维公差分析。E-mail:yangrui@dlut.edu.cn;孙士勇(通信作者),男,1981年出生,博士,副教授,博士研究生导师。主要研究方向为先进飞行器功能结构设计与制造技术。E-mail:sunshy@dlut.edu.cn
  • 基金资助:
    中央高校基本科研业务费专项资金(DUT25GF303)和国家自然科学基金(51675082)资助项目。

3D Tolerance Analysis of Aircraft Four-bar Linkage Doors Based on an Improved SOTA Method

YANG Rui, YANG Linkai, WEI Lei, SUN Shiyong   

  1. School of Mechanical Engineering, Dalian University of Technology, Dalian 116024
  • Received:2025-04-01 Revised:2026-03-25 Published:2026-11-20

摘要: 针对飞机四连杆舱门等由多个并联结构组成的复杂空间机构尚无有效的偏差建模与分析方法,导致装配偏差难以预测、公差设计方案没有有效验证手段的问题,提出了一种可以考虑多并联结构和机构运动特性的复杂装配体三维公差分析方法。该方法首先基于小位移旋量理论将并联结构偏差进行等效描述,从而将舱门从复杂空间机构简化为平面机构。同时考虑公差原则将配合偏差和几何特征偏差等效为综合偏差,以舱门关闭状态下机身与随动舱门的上下阶差为功能要求,建立了舱门的矢量环模型。其次,引入修正向前有限差分法提高泰勒展开影响系数的求解效率,采用奇异值分解解决欠定装配方程求解问题,改进了二阶公差分析方法(Second-order tolerance analysis, SOTA),以提高矢量环模型的求解效率和通用性。最后,利用所提方法对四连杆舱门进行了三维公差分析,给出了舱门的装配偏差累计结果,为公差设计方案的合理性评定提供了参考依据。

关键词: 三维公差分析, 二阶公差分析方法, 矢量环模型, 四连杆舱门

Abstract: An effective deviation modeling and analysis method for complex spatial mechanisms, such as aircraft four-bar linkage doors composed of multiple parallel structures, is currently unavailable. This results in difficulties in predicting assembly deviations and a lack of effective verification for tolerance design schemes. To address these issues, a 3D tolerance analysis method for complex assemblies that considers multiple parallel structures and mechanism motion characteristics is proposed. The deviations in parallel structures are first described equivalently based on the small displacement torsor theory, simplifying the door from a complex spatial mechanism into a planar mechanism. Tolerance principles are applied to equivalently combine mating deviations and geometric feature deviations into comprehensive deviations. The vector loop model of the door is established by considering the upper and lower steps between the fuselage and the follow-up door in the closed state as functional requirements. A modified forward finite difference method is then introduced to improve the efficiency of solving influence coefficients of Taylor expansion, and singular value decomposition is employed to resolve underdetermined assembly equations. The second-order tolerance analysis method is improved to enhance the efficiency and generality of solving the vector loop model. Finally, the proposed method is applied to perform a 3D tolerance analysis of the four-bar linkage door. The cumulative assembly deviations of the door are obtained, providing a reference for evaluating the rationality of tolerance design schemes.

Key words: 3D tolerance analysis, second-order tolerance analysis, vector loop model, four-bar linkage door

中图分类号: