直线伺服系统时滞参数辨识与补偿研究

doi:10.3901/JME.2018.05.193

机械工程学报 ›› 2018, Vol. 54 ›› Issue (5): 193-201.doi: 10.3901/JME.2018.05.193

扫码分享

直线伺服系统时滞参数辨识与补偿研究

杨亮亮^1,2, 时军^1,2, 鲁文其^1,2, 史伟民^1,2

1. 浙江理工大学浙江省现代纺织装备技术重点实验室杭州 310018;
2. 浙江理工大学教育部现代纺织装备技术工程研究中心杭州 310018

收稿日期:2017-01-09 修回日期:2017-10-17 出版日期:2018-03-05 发布日期:2018-03-05
通讯作者: 史伟民(通信作者),男,1965年出生,博士,教授,博士研究生导师。主要研究方向为机电控制技术。E-mail:swm@zstu.edu.cn
作者简介:杨亮亮,男,1978年出生,博士,副教授。主要研究方向为高速高精度运动控制、机器人控制技术和数控技术。E-mail:yangliangliang@zstu.edu.cn
基金资助:
国家自然科学基金资助项目（51305404）。

Research on Identification and Compensation of Linear Servo System Time Delay Parameter

YANG Liangliang^1,2, SHI Jun^1,2, LU Wenqi^1,2, SHI Weimin^1,2

1. Zhejiang Provincial Key Lab of Modern Textile Machinery & Technology, Zhejiang Sci-Tech University, Hangzhou 310018;
2. The Research Center of Modern Textile Machinery Technology of the Ministry of Education, Zhejiang Sci-Tech University, Hangzhou 310018

Received:2017-01-09 Revised:2017-10-17 Online:2018-03-05 Published:2018-03-05

摘要/Abstract

摘要： 为解决直线伺服固有时滞特性对轨迹跟踪性能的影响，以典型的前馈加反馈二自由度控制结构为基础，分析直线伺服时滞特性对其轨迹跟踪精度的影响。在此基础上设计了前馈环节上的时滞控制器，之后针对时滞控制器位于前馈通道时作为一个超前环节控制上无法实现的问题，将时滞参数分为两部分，分别调节理想轨迹指令按照整数倍伺服周期延时及前馈控制信号滤波延时以达到时滞补偿的目的，引入牛顿迭代寻优进行最优时滞参数辨识。仿真与试验结果表明，在前馈加反馈二自由度控制的基础上加入时滞控制器可以有效减小直线伺服系统的闭环位置跟踪误差，特别是显著减小非零加加速度段的闭环位置跟踪误差，提高轨迹跟踪性能。

关键词: 迭代学习优化, 牛顿迭代法, 时滞控制, 直线伺服系统

Abstract: To eliminate the negative influence of intrinsic linear servo system time delay on the trajectory tracking performance, the reason behind the negative influence of linear servo system time delay on the tracking accuracy designed based on a typical two-degree-of-freedom controller structure with feedforward-feedback controller is theoretically analyzed. And then a time delay controller is designed to compensate the delay effect based on analysis. To conquer the non-realization of delay controller located in the feedforward path as a lead link the time delay is divided into two parts, one is a integrally multiple of servo cycle for adjusting the ideal trajectory command delay and located in the path of ideal trajectory command, another acts as a time parameter of feedforward control signal filter. And then the Newton iteration method is introduced to identify the optimal time delay control parameter. Simulation and experimental results show that the position tracking error of closed loop linear servo system can be reduced by adding the time-delay controller to the two degree of freedom controllers. Particularly the tracking error of nonzero jerk phases in trajectory is significantly reduced and finally the tracking performance is improved.

Key words: iterative learning optimization, linear servo system, newton iteration method, time delay control

中图分类号:

TP391

杨亮亮, 时军, 鲁文其, 史伟民. 直线伺服系统时滞参数辨识与补偿研究[J]. 机械工程学报, 2018, 54(5): 193-201.

YANG Liangliang, SHI Jun, LU Wenqi, SHI Weimin. Research on Identification and Compensation of Linear Servo System Time Delay Parameter[J]. Journal of Mechanical Engineering, 2018, 54(5): 193-201.

参考文献

[1] 张倩,万里冰,赵彤.直线电动机在高档数控机床上的应用现状[J].航空制造技术,2013(5):52-54. ZHANG Qian,WAN Libing,ZHAO Tong. Application of linear motor in high-end machine tool[J]. Aeronautical Manufacturing Technology,2013(5):52-54.
[2] 陈兴林,刘川,耿长青,等.光刻机工件台直线电动机的完全跟踪控制[J].中南大学学报,2015,46(9):3238-3244 CHEN Xinglin,LIU Chuan,GENG Changqing,et al. Perfect tracking control for linear motor in wafer stage of lithography[J]. Journal of Central South University,2015,46(9):3238-3244.
[3] 王丽梅,李兵.直线电动机驱动XY平台的速度场轨迹规划与控制研究[J].中国电动机工程学报,2014,34(3):438-444. WANG Limei,LI Bing. Research on trajectory planning of contour control for a linear motor drive XY table based on velocity field[J]. Proceedings of the CSEE,2014,34(3):438-444.
[4] 石阳春,周云飞,李鸿,等.长行程直线电动机的迭代学习控制[J].中国电动机工程学报,2007,27(24):92-96. SHI Yangchun,ZHOU Yunfei,LI Hong,et al. Research on Iterative learning control to long stroke linear motor[J]. Proceedings of the CSEE,27(24):92-96.
[5] 张刚,刘品宽,张波,等.直线电动机精密运动平台轨迹跟踪控制器设计[J].光学精密工程,2013,12(2):371-379. ZHANG Gang,LIU Pinkuan,ZHANG Bo,et al. Design of trajectory tracking controller for precision positioning table driven by linear motor[J]. Optics and Precision Engineering,2013,12(2):371-379.
[6] 陈兴林,刘川,周乃新,等.基于ZPETC-FF和DOB的精密运动平台控制[J].哈尔滨工业大学学报,2014,46(1):1-6. CHEN Xinglin,LIU Chuan,ZHOU Naixin,et al Controller design based on ZPETC-FF and DOB for precision motion platform[J]. Journal of Harbin Institute of Technology,2014,46(1):1-6.
[7] 陶大锦,柯大观,袁柳斌,等. 直线伺服系统模型参数辨识及其试验研究[J]. 中国机械工程,2013,24(7),915-921. TAO Dajin,KE Daguan,YUAN Liubin,et al. Parameter identification and experimental research of a linear servo system[J]. China Mechanical Engineering,2013,24(7),915-921.
[8] 陈兴林,杨天博,刘杨. 直线电动机定位力波动的辨识及迭代补偿方法[J]. 电动机与控制学报,2015, 19(2):60-65. CHEN Xinglin,YANG Tianbo,LIU Yang. Method of cogging Force compensation for linear motor based on model identification and iterative learning[J]. Electric Machines and Control,2015,19(2):60-65.
[9] YAO Bin,XU Li. Adaptive robust motion control of linear motors for precision manufacturing[J]. Mechatronics,2002,12:595-616.
[10] HODAY S,SANDIPAN M,MASAYOSHI T. Iterative tuning of feedforward controller with force ripple compensation for wafer stage[J]. IEEE,2008:234-239.
[11] ZHAO S,TAN K K. Adaptive feedforward compensation of force ripples in linear motors[J]. Control Engineering Practice 13,2005:2081-1092.
[12] MARCEL H,DAAN H,MAARTEN S. MIMO feed-forward design in wafer scanners using a gradient approximation-based algorithm[J]. Control Engineering Practice18,2010:495-506.
[13] PAUL L,MATTHIJS B,MAARTEN S. Trajectory planning and feedforward design for electromechanical motion systems[J]. Control Engineering Practice,2005,13:145-157.
[14] STAN H,van der MEULEN. Fixed structure feedforward control design exploiting iterative trials:Application to a water stage and a desktop printer[J]. ASME Journal of Dynamic Systems,Measurement,and Control,2008,130:1-16.
[15] 杨亮亮,武晓虎,史伟民,等. 基于正交投影迭代学习的高频响闭环运动控制系统模型参数辨识研究[J]. 机械工程学报,2015,51(1):188-195. YANG Liangliang,WU Xiaohu,SHI Weimin,et al. Research on model parameters identification of closed-loop high frequency motion control system based on iterative learning of orthogonal projection[J]. Journal of Mechanical Engineering,2015,51(1),188-195.

直线伺服系统时滞参数辨识与补偿研究

Research on Identification and Compensation of Linear Servo System Time Delay Parameter

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 1

编辑推荐

Metrics

本文评价