基于自回归谱外推方法的TOFD检测盲区抑制

doi:10.3901/JME.2018.22.015

机械工程学报 ›› 2018, Vol. 54 ›› Issue (22): 15-20.doi: 10.3901/JME.2018.22.015

扫码分享

基于自回归谱外推方法的TOFD检测盲区抑制

孙旭¹, 金士杰¹, 张东辉², 刘丽丽², 杨会敏³, 林莉¹

1. 大连理工大学无损检测研究所大连 116085;
2. 中国核工业二三建设有限公司北京 101300;
3. 核工业工程研究设计有限公司北京 101300

收稿日期:2018-02-02 修回日期:2018-07-03 出版日期:2018-11-20 发布日期:2018-11-20
通讯作者: 林莉(通信作者),女,1970年出生,博士,教授,博士研究生导师。主要研究方向为材料无损检测与评价。E-mail:linli@dlut.edu.cn
作者简介:孙旭,男,1993年出生。主要研究方向为超声无损检测信号处理。E-mail:v004sunxu@mail.dlut.edu.cn
基金资助:
国家重点基础研究发展计划（973计划，2015CB057306）和中央高校基本科研业务费专项资金（DUT17RC（4）02）资助项目。

Suppressionof Dead Zone in TOFD with Autoregressive#br# Spectral Extrapolation

SUN Xu¹, JIN Shijie¹, ZHANG Donghui², LIU Lili², YANG Huimin³, LIN Li¹

1. NDT & E Laboratory, Dalian University of Technology, Dalian 116085;
2. China Nuclear Industry 23 Construction Co., Ltd., Beijing 101300;
3. Nuclear Industry Research and Engineering Co., Ltd., Beijing 101300

Received:2018-02-02 Revised:2018-07-03 Online:2018-11-20 Published:2018-11-20

摘要/Abstract

摘要： 结合自回归谱外推方法与超声衍射时差法（Time of flight diffraction，TOFD），抑制直通波脉冲宽度造成的近表面检测盲区。建立碳钢试块模型，并设置上尖端埋深d依次为2.5 mm、3.0 mm、5.0 mm及7.0 mm的底面开口槽，模拟选用中心频率5 MHz、探头中心距34.0 mm的TOFD探头实施检测。利用自回归谱外推方法扩宽傅里叶变换后的混叠信号频带，压缩时域脉冲宽度，分离了混叠的直通波与衍射波，将TOFD检测盲区深度由8.3 mm抑制到2.5 mm以内，实现四个底面开口槽的同时检出与定位。针对碳钢试块中埋深3.0 mm底面开口槽进行试验验证，定位误差为0.30 mm。与常规TOFD和频谱分析方法相比，自回归谱外推方法以高信噪比频带为基础，外推有效频带外的高频与低频范围数据，提高时间分辨率，为TOFD检测盲区内缺陷定位提供了新思路。

关键词: 超声衍射时差法, 盲区, 缺陷定位, 自回归谱外推

Abstract: Combining the autoregressive spectral extrapolation method with the ultrasonic time of flight diffraction method, the near surface detection blind area caused by the pulse width of lateral wave is suppressed. A carbon steel test block model having bottom notches with depth of 2.5 mm, 3 mm, 5 mm and 7 mm is set up. In the simulation, the model is detected using TOFD probes with 5 MHz center frequency and 34.0 mm probe center spacing (PCS). Autoregressive spectral extrapolation method extends the frequency band, compresses time-domain pulse width and separates the overlapping signal. The depth of dead zone is reduced from 8.3 mm to 2.5 mm and four bottom notchesare detected and positioned. Bottom notch having 3.0 mm depth is calculated with the same testing parameters in experiment, and the detected result has an absolute error of 0.30 mm. Compared with conventional TOFD and spectrum analysis methods, autoregressive spectral extrapolation method based on high SNR frequency bands and extrapolate the high frequency and low frequency range data outside the effective band, achieves the goal of improving time resolution and provides a new way for TOFD to detect defects in blind areas.

Key words: autoregressive spectral extrapolation, dead zone, defect positioning, time of flight diffraction

中图分类号:

TG115

孙旭, 金士杰, 张东辉, 刘丽丽, 杨会敏, 林莉. 基于自回归谱外推方法的TOFD检测盲区抑制[J]. 机械工程学报, 2018, 54(22): 15-20.

SUN Xu, JIN Shijie, ZHANG Donghui, LIU Lili, YANG Huimin, LIN Li. Suppressionof Dead Zone in TOFD with Autoregressive#br# Spectral Extrapolation[J]. Journal of Mechanical Engineering, 2018, 54(22): 15-20.

参考文献

[1] BASKARAN G,BALASUBRAMANIAM K,KRISHNAMURTHY C V. TOFD imaging:Ultrasonic TOFD flaw sizing and imaging in thin plates using embedded signal identification technique (ESIT)[J]. Insight-Non-Destructive Testing and Condition Monitoring,2004,46(9):537-542.
[2] 迟大钊,刚铁,盛朝阳. 超声渡越时差法检测图像中裂纹端部信号的识别[J]. 机械工程学报,2007,43(10):103-107. CHI Dazhao,GANG Tie,SHENG Chaoyang. Method for crack tip recognition in an ultrasonic time of flight diffraction image[J]. Journal of Mechanical Engineering,2007,43(10):103-107.
[3] 谢雪,祝美丽,杨会敏,等. 合成孔径聚焦技术在超声衍射时差法缺陷长度定量中的应用研究[J]. 机械工程学报,2015,51(18):20-25. XIE Xue,ZHU Meili,YANG Huimin,et al. Research of synthetic aperture focusing technology in the application of crack length sizing by time of flight diffraction technique[J]. Journal of Mechanical Engineering,2015,51(18):20-25.
[4] MERAZI-MEKSEN T,BOUDRAA M,BOUDRAA B. Mathematical morphology for TOFD image analysis and automatic crack detection[J]. Ultrasonics,2014,54(6):1642-1648.
[5] 丁宁,金士杰,张东辉,等. 基于波型转换的TOFD近表面盲区抑制研究[J]. 机械工程学报,2017,53(16):120-124. DING Ning,JIN Shijie,ZHANG Donghui,et al. Research on near surface dead zone reduction of TOFD based on mode-converted theory[J]. Journal of Mechanical Engineering,2017,53(16):120-124.
[6] 谢雪. 提高压力容器焊缝TOFD检测分辨率方法的研究[D]. 大连:大连理工大学,2015. XIE Xue. Research of improving TOFD resolution based on pressure vessel welds[D]. Dalian:Dalian University of Technology,2015.
[7] 崔哲. 不锈钢堆焊层结构超声TOFD检测参数优化试验研究[D]. 大连:大连理工大学,2015. CUI Zhe. Experimental research of parameters optimization on the stainless steel cladding layer using TOFD technique[D]. Dalian:Dalian University of Technology,2015.
[8] 卢超,王鑫,陈振华. 近表面缺陷的超声TOFDR和TOFDW检测[J]. 失效分析与预防,2012,7(3):153-157. LU Chao,WANG Xin,CHEN Zhenhua. Ultrasonic TOFDR and TOFDW for near surface defect detection[J]. Failure Analysis & Prevention,2012,7(3):153-157.
[9] 迟大钊,刚铁,姚英学,等. 一种基于超声TOFD法的近表面缺陷检测模式[J]. 焊接学报,2011,32(2):25-28. CHI Dazhao,GANG Tie,YAO Yingxue,et al. Mode for near surface defect detection based on ultrasonic TOFD[J]. Transactions of the China Welding Institution,2011,32(2):25-28.
[10] YANG Chenlong,WANG Liqiu,XU Zhinong. Improved Hilbert transform to process the ultrasonic TOFD signal[C]//Control Conference IEEE,2010,Beijing,China.
[11] 赵烨,方正中,郑鼎鼎,等. 小波匹配追踪技术在超声TOFD图像处理中的应用[J]. 杭州电子科技大学学报,2016,36(5):26-30. ZHAO Ye,FANG Zhengzhong,ZHENG Dingding,et al. Application of wavelet matching pursuit technique in ultrasonic TOFD image processing[J]. Journal of Hangzhou Dianzi University,2016,36(5):26-30.
[12] 张树潇,谢雪,刘丽丽,等. 基于频谱分析原理减小TOFD检测近表面盲区的方法[J]. 无损探伤,2013,37(6):20-21. ZHANG Shuxiao,XIE Xue,LIU Lili,et al. Decreasing near surface dead zone of TOFD method based on spectral analysis[J]. Nondestructive Test,2013,37(6):20-21.
[13] ZHAO Yang,LIN Li,LI Ximeng. Simultaneous determination of the coating thickness and its longitudinal velocity by ultrasonic nondestructive method[J]. NDT & E International,2010,43(7):579-585.
[14] LINES L R,CLAYTON R W. A new approach to vibroseisdeconvolution[J]. Geophysical Prospecting,1977,25(3):417-433.
[15] HONARVAR F,SHEIKHZADEH H,MOLES M. Improving the time-resolution and signal-to-noise ratio of ultrasonic NDE signals[J]. Ultrasonics,2004,41(9):755-763.
[16] 张树潇,谢雪,刘丽丽,等. 核反应堆厚壁压力容器焊缝TOFD检测缺陷高度分辨率探究[J]. 压力容器,2014,31(6):64-69. ZHANG Shuxiao,XIE Xue,LIU Lili,et al. Inquiry of height resolution of heavy walled nuclear reactor pressure vessels in TOFD testing[J]. Pressure Vessel Technology,2014,31(6):64-69.
[17] GUO J,XIN Y. Reconstructing outside pass-band data to improve time resolution in ultrasonic detection[J]. NDT & E International,2012,50:50-57.
[18] HERRERA R H,LIU Z,RAFFA N. Improving time estimation by blind deconvolution:With applications to TOFD and backscatter sizing[C]//Canada's NDT Conference,2015,Edmonton,Canada.
[19] KARSL H. Further improvement of temporal resolution of seismic data by autoregressive (AR) spectral extrapolation[J]. Journal of Applied Geophysics,2006,59(4):324-336.
[20] DASGUPTA S,NOWACK R L. Frequency extrapolation to enhance the deconvolution of transmitted seismic waves[J]. Journal of Geophysics & Engineering,2008,5(1):118-127.
[21] 强天鹏,肖雄,李智军,等. TOFD技术的检测盲区计算和分析[J]. 无损检测,2008,30(10):77-79. QIANG Tianpeng,XIAO Xiong,LI Zhijun,et al. Calculation for the blind zone of TOFD testing technology and its characteristic analysis[J]. Nondestructive Testing,2008,30(10):77-79.
[22] KAY S M,MARPLE S L J. Spectrum analysis-a modern perspective[J]. Proceedings of the IEEE,1981,69(11):1380-1419.

基于自回归谱外推方法的TOFD检测盲区抑制

Suppressionof Dead Zone in TOFD with Autoregressive#br# Spectral Extrapolation

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 7

编辑推荐

Metrics

本文评价

[1]	金士杰, 张波, 孙旭, 王志诚, 林莉. 基于TOFD周向扫查图像特征的管道缺陷超声检测[J]. 机械工程学报, 2023, 59(4): 18-24.
[2]	杨庆宁, 解社娟, 何琨, 王凯强, 仝宗飞, 陈洪恩, 陈振茂. 一种新型环向偏心涡流探头及其在小径管缺陷检测中的应用[J]. 机械工程学报, 2021, 57(12): 109-117.
[3]	林莉, 史思琪, 孙旭, 马志远, 张晓峰, 刘丽丽, 金士杰. 基于自回归谱外推的全聚焦成像分辨力提升[J]. 机械工程学报, 2020, 56(22): 8-13,23.
[4]	吕广强,沙尧. 基于参数自适应的孤岛检测算法研究[J]. 电气工程学报, 2017, 12(5): 8-14.
[5]	丁宁, 金士杰, 张东辉, 康达, 张树潇, 雷明凯, 刘丽丽, 林莉. 基于波型转换的TOFD近表面盲区抑制研究[J]. 机械工程学报, 2017, 53(16): 120-124.
[6]	黎敏, 宋亚男, 周通, 徐金梧. 基于数学形态学的超声信号盲区内缺陷特征提取方法[J]. 机械工程学报, 2016, 52(12): 16-22.
[7]	谢雪, 祝美丽, 杨会敏, 崔哲, 张东辉, 林莉, 张树潇, 刘丽丽. 合成孔径聚焦技术在超声衍射时差法缺陷长度定量中的应用研究[J]. 机械工程学报, 2015, 51(18): 20-25.