基于波型转换的TOFD近表面盲区抑制研究

doi:10.3901/JME.2017.16.120

机械工程学报 ›› 2017, Vol. 53 ›› Issue (16): 120-124.doi: 10.3901/JME.2017.16.120

• 特邀专栏：汽车先进动力系统的设计、优化与控制（下） • 上一篇下一篇

扫码分享

基于波型转换的TOFD近表面盲区抑制研究

丁宁¹, 金士杰¹, 张东辉², 康达¹, 张树潇², 雷明凯³, 刘丽丽², 林莉¹

1. 大连理工大学无损检测研究所大连 116024;
2. 中国核工业二三建设有限公司北京 101300;
3. 大连理工大学材料科学与工程学院大连 116024

收稿日期:2016-11-23 修回日期:2017-04-17 发布日期:2017-08-20
通讯作者: 林莉(通信作者),女,1970年出生,博士,教授,博士研究生导师。主要研究方向为材料无损检测与评价,已发表论文100余篇。E-mail:linli@dlut.edu.cn E-mail:linli@dlut.edu.cn
作者简介:丁宁,女,1992年出生。主要研究方向为TOFD检测技术。E-mail:dlutdning@163.com.
基金资助:
国家重点基础研究发展计划资助项目（973计划，2015CB057306）

Research on Near Surface Dead Zone Reduction of TOFD Based on Mode-converted Theory

DING Ning¹, JIN Shijie¹, ZHANG Donghui², KANG Da¹, ZHANG Shuxiao², LEI Mingkai³, LIU Lili², LIN Li¹

1. NDT & E Laboratory, Dalian University of Technology, Dalian 116024;
2. China Nuclear Industry 23 Construction Co., Ltd., Beijing 101300;
3. School of Materials Science and Engineering, Dalian University of Technology, Dalian 116024

Received:2016-11-23 Revised:2017-04-17 Published:2017-08-20

摘要/Abstract

摘要： 针对超声衍射时差法（Time of flight diffraction，TOFD）存在的近表面盲区问题，基于波型转换理论，提出盲区抑制方法。根据TOFD平行扫查时变型波变化规律，明确裂纹深度d与变型波声程最短时缺陷偏心距△S之间的理论关系。考虑到△S读数误差较大的问题，引入直通波与变型波声程最短位置点间的垂直距离d'，从而实现近表面盲区抑制。选用中心频率10 MHz、折射角度70°；以及探头中心间距（Probe center spacing，PCS）17.00 mm的TOFD探头对，通过模拟与试验的方法对厚度35.00 mm碳钢试块中深度1.00~6.00 mm的底面开口槽进行平行扫査和定位检测。结果表明，该方法可将近表面盲区抑制到1.00 mm，深度2.00 mm底面开口槽定位误差最大，误差绝对值为0.24 mm。

关键词: 变型波, 超声衍射时差法, 近表面盲区, 缺陷定位

Abstract: To reduce the near surface dead zone in time of flight diffraction(TOFD), one method is proposed based on mode-converted theory. According to the variation of mode-converted waves in parallel scanning of TOFD, the theoretical relationship between flaw depth d and offset distance △S is confirmed. Considering the reading error of △S, the vertical distance d' between lateral wave and mode-converted wave having a shortest ultrasonic path is introduced to achieve the reduction of near surface dead zone. Selecting a pair of TOFD probes with 10 MHz center frequency, 70° refraction angle and 17.00 mm Probe center spacing(PCS), surface breaking notches at bottom, whose depths are from 1.00 mm to 6.00 mm in carbon steel, are inspected in parallel way and located by simulation and experiment. The result shows that near surface dead zone can be suppressed to 1.00 mm, and the biggest absolute located error is 0.24 mm when the notch depth is 2.00 mm.

Key words: flaw localization, mode-converted waves, near surface dead zone, time of flight diffraction

中图分类号:

TG156

丁宁, 金士杰, 张东辉, 康达, 张树潇, 雷明凯, 刘丽丽, 林莉. 基于波型转换的TOFD近表面盲区抑制研究[J]. 机械工程学报, 2017, 53(16): 120-124.

DING Ning, JIN Shijie, ZHANG Donghui, KANG Da, ZHANG Shuxiao, LEI Mingkai, LIU Lili, LIN Li. Research on Near Surface Dead Zone Reduction of TOFD Based on Mode-converted Theory[J]. Journal of Mechanical Engineering, 2017, 53(16): 120-124.

参考文献

[1] 盛朝阳,刚铁,迟大钊. 基于分水岭方法的超声TOFD检测图像分割[J].机械工程学报, 2011, 47(8):35-40. SHENG Chaoyang, GANG Tie, CHI Dazhao. Segmentation of ultrasonic TOFD testing image based on watershed method[J]. Journal of Mechanical Engineering, 2011, 47(8):35-40.
[2] 谢雪,祝美丽,杨会敏,等. 合成孔径聚焦技术在超声衍射时差法缺陷长度定量中的应用研究[J].机械工程学报, 2015, 51(18):20-25. XIE Xue, ZHU Meili, YANG Huimin, et al. Research of synthetic aperture focusing technology in the application of crack length sizing by time of flight diffraction techinique[J]. Journal of Mechanical Engineering, 2015, 51(18):20-25.
[3] MERAZI M, BOUDRAA M, BOUDRAA B. Mathematical morphology for TOFD image analysis and automatic crack detection[J]. Ultrasonics, 2014, 54(6):1642-1648.
[4] BASKARAN G, BALASUBRAMANIAM K, KRISHNAMURTHY C, et al. Ultrasonic TOFD flaw sizing and imaging in thin plates using embedded signal identification technique(ESIT)[J]. Insight Non-Destru ctive Testing and Condition Monitoring, 2004, 46(9):1-6.
[5] 张树潇,谢雪,刘丽丽,等. 基于频谱分析原理减小TOFD检测近表面盲区的方法[J]. 无损探伤, 2013, 37(6):20-22. ZHANG Shuxiao, XIE Xue, LIU Lili, et al. Decreasing near surface dead zone of TOFD method based on spectral analysis[J]. Nondestructive Test, 2013, 37(6):20-22.
[6] 白艳, 邢涛. TOFD技术检测盲区的研究[J]. 森林工程, 2010, 26(4):50-53. BAI Yan, XING Tao. Research on TOFD technology to detect the blind zone[J]. Forest Engineering, 2010, 26(4):50-53.
[7] 谢雪. 提高压力容器焊缝TOFD检测分辨率方法的研究[D]. 大连:大连理工大学, 2015. XIE Xue. Research of improving TOFD resolution based on pressure vessel welds[D]. Dalian:Dalian University of Technology, 2015.
[8] 陈天璐, 阙沛文. 基于超声衍射反射回波渡越时间的缺陷识别技术[J]. 化工自动化及仪表, 2006, 33(4):50-52. CHEN Tianlu, QUE Peiwen. The technology of recognizing defect based on ultrasonic time of flight diffraction[J]. Control and Instruments in Chemical Industry, 2006, 33(4):50-52.
[9] CHI D, GANG T. Shallow buried defect testing method based on ultrasonic TOFD[J]. Journal of Nondestructive Evaluation, 2013, 32(2):164-171.
[10] BASKARAN G, BALASUBRAMANIAM K, LASKHMAN RAO C. Shear-wave time of flight diffraction(S-TOFD) technique[J]. NDT & E International, 2006, 39(6):458-467.
[11] 林乃昌. 基于变型波的超声TOFD近表面检测新方法[J].机电工程, 2013, 30(8):967-970. LIN Naichang. New near surface detection method of ultrasonic TOFD based on transformed wave[J]. Journal of Mechanical & Electrical Engineering, 2013, 30(8):967-970.
[12] KECHIDA A, DRAI R, BENAMMAR A. Image processing and wavelets transform for sizing of weld defects using ultrasonic TOFD images[J]. Journal of the Acoustical Society of America, 2008, 123(5):1079-1084.
[13] 强天鹏,肖雄,李智军,等. TOFD技术的检测盲区计算和分析[J]. 无损检测, 2008, 30(10):738-740. QIANG Tianpeng, XIAO Xiong, LI Zhijun, et al. Calculation for the blind zone of TOFD testing technology and its characteristic analysis[J]. Nondestructive Testing, 2008, 30(10):738-740.
[14] 孙忠波,郑红霞,张平. TOFD检测中借助变型波确定缺陷偏心距及缺陷精确深度的探讨[J]. 无损检测, 2010, 32(7):500-503. SUN Zhongbo, ZHENG Hongxia, ZHANG Ping. The disscussion on defining the eccentricity and accurate depth of defect by TOFD transformed wave[J]. Nondestructive Testing, 2010, 32(7):500-503.
[15] 史亦韦. 超声检测[D]. 北京:机械工业出版社, 2005. SHI Yiwei. Ultrasonic testing[D]. Beijing:China Machine Press, 2005.

基于波型转换的TOFD近表面盲区抑制研究

Research on Near Surface Dead Zone Reduction of TOFD Based on Mode-converted Theory

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 4

编辑推荐

Metrics

本文评价

[1]	金士杰, 张波, 孙旭, 王志诚, 林莉. 基于TOFD周向扫查图像特征的管道缺陷超声检测[J]. 机械工程学报, 2023, 59(4): 18-24.
[2]	杨庆宁, 解社娟, 何琨, 王凯强, 仝宗飞, 陈洪恩, 陈振茂. 一种新型环向偏心涡流探头及其在小径管缺陷检测中的应用[J]. 机械工程学报, 2021, 57(12): 109-117.
[3]	孙旭, 金士杰, 张东辉, 刘丽丽, 杨会敏, 林莉. 基于自回归谱外推方法的TOFD检测盲区抑制[J]. 机械工程学报, 2018, 54(22): 15-20.
[4]	谢雪, 祝美丽, 杨会敏, 崔哲, 张东辉, 林莉, 张树潇, 刘丽丽. 合成孔径聚焦技术在超声衍射时差法缺陷长度定量中的应用研究[J]. 机械工程学报, 2015, 51(18): 20-25.