基于各向异性的薄带冷轧变形区接触压力模型研究

doi:10.3901/JME.2025.08.127

机械工程学报 ›› 2025, Vol. 61 ›› Issue (8): 127-137.doi: 10.3901/JME.2025.08.127

• 材料科学与工程 • 上一篇

扫码分享

基于各向异性的薄带冷轧变形区接触压力模型研究

李伟^1,2, 黄紫藤^1,2, 李松松^1,2, 于辉^1,2, 罗许³

1. 燕山大学机械工程学院秦皇岛 066004;
2. 燕山大学国家冷轧板带装备及工艺工程技术研究中心秦皇岛 066004;
3. 攀钢集团攀枝花钢铁研究院有限公司攀枝花 617000

收稿日期:2024-04-22 修回日期:2024-09-25 发布日期:2025-05-10
作者简介:李伟，男，1995年出生，博士。主要研究方向为薄板带轧制变形理论。E-mail：liweiaedu@163.com;黄紫藤，女，2000年出生，硕士研究生。主要研究方向为机械超材料变形理论。E-mail：hziteng1002@163.com;李松松，男，1995年出生，博士研究生。主要研究方向为复合板轧制变形理论。E-mail：lss1252965104@163.com;于辉(通信作者)，男，1974年出生，教授，博士研究生导师。主要研究方向为金属加工成形机理及工艺优化。E-mail：yuhui@ysu.edu.cn;罗许，男，1982年出生，博士，教授级高级工程师。主要研究方向为材料加工工艺、钒钛新材料开发。E-mail：18982379352@163.com
基金资助:
河北省自然科学基金(E2021203237)和中央引导地方科技发展资金(216Z1002G)资助项目。

Research on Contact Pressure Model of Cold Rolled Deformation Zone of Thin Strip Based on Anisotropy

LI Wei^1,2, HUANG Ziteng^1,2, LI Songsong^1,2, YU Hui^1,2, LUO Xu³

1. College of Mechanical Engineering, Yanshan University, Qinhuangdao 066004;
2. National Engineering Research Center for Equipment and Technology of Cold Strip Rolling, Yanshan University, Qinhuangdao 066004;
3. Panzhihua Steel Group Panzhihua Iron and steel Research Institute Co., Ltd., Panzhihua 617000

Received:2024-04-22 Revised:2024-09-25 Published:2025-05-10

摘要/Abstract

摘要： 传统薄带轧制变形区理论中常将轧件假设为理想的各向同性材料，而并未考虑材料本身或后续处理过程中所引入的各向异性问题，导致理论预测精度大幅降低的同时也给后续工艺的合理制定带来巨大困难。为此采用理论分析、数值模拟和实验验证相结合的手段开展了屈服应力取值合理性和屈服判据差异性对变形区接触特征影响规律的研究。结果表明：屈服应力的不合理取值和屈服判据的差异会导致变形区轮廓、各分区临界点坐标和实际压下率等大幅偏离实际，表现为屈服应力取值更高的轧件的中性区出现得更早且宽度占比更大，而Mises各向同性屈服判据时等效应力的判别结果要比Hill48正交各向异性判据更早达到轧件屈服。以RD拉伸屈服应力为参考，由各向异性系数所修正的变形区接触压力模型能够较好地预测各向异性薄带轧制变形区的接触特征。

关键词: 薄带材, 轧制, 变形区理论, 屈服准则, 各向异性

Abstract: In the traditional thin strip rolling deformation zone theory, the rolling parts are often assumed to be ideal isotropic materials, without considering the anisotropy problem introduced in the material itself or the subsequent processing, which significantly reduces the accuracy of theoretical predictions and creates significant challenges for the rational formulation of the subsequent process. Therefore, to investigate the influence of the differences in yield criteria and the rationality of yield stress on the contact characteristics of the deformation zone, a combination of the theoretical analysis, numerical simulation, and experimental verification is used. The results show that the unreasonable value of yield stress and the difference of yield criterion will result in a significant deviation from the reality of the deformation zone profile, the coordinates of the critical point of each zone, and the actual compression rate. The neutral zone of the rolled piece with higher yield stress value appears earlier and the width proportion is larger, and the discrimination result of the equivalent stress of the MISES isotropic yield criterion reaches the yield of the rolled piece earlier than that of the HILL48 orthotropic criterion. The contact characteristics of the rolling deformation zone of the anisotropic thin strip can be more accurately predicted by the contact pressure model of the deformation zone modified by the anisotropy coefficient, using the RD tensile yield stress as a reference.

Key words: thin strip, rolling, deformation zone theory, yield criterion, anisotropy

中图分类号:

TG331

李伟, 黄紫藤, 李松松, 于辉, 罗许. 基于各向异性的薄带冷轧变形区接触压力模型研究[J]. 机械工程学报, 2025, 61(8): 127-137.

LI Wei, HUANG Ziteng, LI Songsong, YU Hui, LUO Xu. Research on Contact Pressure Model of Cold Rolled Deformation Zone of Thin Strip Based on Anisotropy[J]. Journal of Mechanical Engineering, 2025, 61(8): 127-137.

参考文献

[1] 任忠凯，郭雄伟，范婉婉，等. 精密极薄带轧制理论研究进展及展望[J]. 机械工程学报，2020，56(12)：73-84. REN Zhongkai，GUO Xiongwei，FAN Wanwan，et al. Research progress and prospects of precision ultra-thin strip rolling theory[J]. Journal of Mechanical Engineering，2020，56(12)：73-84.
[2] MISHRA M K，DUBEY V，MISHRA P M，et al. MEMS technology：a review[J]. Journal of Engineering Research and Reports，2019，4(1)：1-24.
[3] FU M，WANG J，KORSUNSKY A M. A review of geometrical and microstructural size effects in micro-scale deformation processing of metallic alloy components[J]. International Journal of Machine Tools & Manufacture，2016，109：94-125.
[4] 刘亚星，顾清，张文军，等. 超高强钢冷轧过程轧制力计算的改进模型[J]．钢铁，2021，56(10)：108-116. LIU Yaxing，GU Qing，ZHANG Wenjun，et al. Improved model for calculating rolling load of ultra-high strength steel in cold rolling process[J]. Iron and Steel，2021，56(10)：108-116.
[5] ALHARBI H F，MONIS L，EHAB E D，et al. Experimental and numerical study of texture evolution and anisotropic plastic deformation of pure magnesium under various strain paths[J]. Advances in Materials Science and Engineering，2018(1)：1-12.
[6] NIU L，WANG S，CHEN C，et al. Mechanical behavior and deformation mechanism of commercial pure titanium foils[J]. Materials Science and Engineering A，2017，707：435-442.
[7] PIRGAZI H，AKBARZADEH A，PETROV R，et al. Microstructure evolution and mechanical properties of AA1100 aluminum sheet processed by accumulative roll bonding[J]. Materials Science and Engineering A，2008，497：132-138.
[8] LOORENTZ，YOUNG G K. Microstructure evolution and mechanical properties of severely deformed Al alloy processed by differential speed rolling[J]. Journal of Alloys and Compounds，2012，536(S)：S122-S125.
[9] LI W，LI S S，YU H. Research on the anisotropy of plastic behavior and deformation mechanism of textured pure titanium[J]. Materials Characterization，2022，194：112483.
[10] LI W，LI S S，HUANG Z T，et al. Research on the anisotropic mechanism of plastic behavior during tensile process of textured pure titanium[J]. Materials Science and Engineering A，2024，894：146153.
[11] LI W，WANG S Z，HUANG Z T，et al. Anisotropic mechanism of cold-rolled pure titanium plate during the two-step tensile process of the variable path[J]. Materials Science and Engineering A，2024，906：146755.
[12] KARMAN T V. On the theory of rolling[J]. ZAMMZeitschrift fur Angewandte Mathematik und Mechanik，1925，5：139-141.
[13] FRESHWATER I J. Simplified theories of flat rolling-I. the calculation of roll pressure, roll force and roll torque[J]. International Journal of Mechanical Science，1996，38(6)：633-648.
[14] KUHN H A，Weinstein A S. Lateral distribution of pressure in thin strip rolling[J]. Journal of Engineering for Industry，1970，5：453-459.
[15] KUHN H A，Weinstein A S. The minimum gauge problem in thin strip rolling[J]. Journal of Engineering for Industry，1971，7：331-340.
[16] HITCHCOCK J H. Report of ASME special research committee roll neck bearings[R]. New York：ASME Research Publictions，1935.
[17] STONE M D. Rolling of thin strip partⅡ[J]. Iron and Steel Engineer，1956，33(12)：55-76.
[18] TATENO J，HIRUTA T，KATSURA S，et al. Experimental analysis of thickness reduction limits in ultra-thin stainless steel foil rolling[J]. ISIJ International，2011，51(5)：788-792.
[19] OROWAN E，ING D. The calculation of roll pressure in hot and cold flat rolling[J]. Proceedings Institute of Mechanical Engineering，1943，150(4)：140-167.
[20] FORD H，ELLIS F，BLAND D R. Cold rolling with strip tension[J]. Journal of the Iron and Steel Institute，1951，168(1)：57-72.
[21] FORD H，ALEXANDER J M. Rolling hard materials in thin gauges [J]. Journal of the Institute of Metals，1960，88(6)：193-199.
[22] BENTALL R H，JOHNSON K L. An elastic strip in plane rolling contact[J]. International Journal of Mechanical Science，1968，10(8)：637-663.
[23] JOHNSON K L，BENTALL R H. The onset of yield in the cold rolling of thin strip[J]. Journal of the Mechanics and Physics of Solids，1969，17(4)：253-264.
[24] FLECK N A，JOHNSON K L. Towards a new theory of cold rolling thin foil[J]. International Journal of Mechanical Sciences，1987，29(7)：507-524.
[25] FLECK N A，JOHNSON K L，Mear M E，et al. Cold rolling of foil[J]. Proceedings of The Institution of Mechanical Engineers Part B-Journal of Engineering Manufacture，1992，206(2)：119-131.
[26] LANGLANDS T A M，MCELWAIN D L S. A modifed hertzian foil rolling model approximations based on perturbation methods[J]. International Journal of Mechanical Sciences，2002，44(8)：1715-1730.
[27] LANGLANDS T A M，MCELWAIN D L S，Domanti S A. An approximate method for the solution of an influence function foil rolling model[J]. International Journal of Mechanical Sciences，2004，46(8)：1139-1156.
[28] LIU Y，LEE W H. Mathematical model for the thin strip cold rolling and temper rolling process with the influence function method[J]. ISIJ International，2005，45(8)：1173-1178.
[29] WU C H，ZHANG L C，QU P L，et al. Effect of the elastic deformation of rolls on the surface texture transfer in skin-pass rolling[J]. International Journal of Mechanical Sciences，2021，198：106358.
[30] XIAO H，REN Z K，LIU X. New mechanism describing the limiting producible thickness in ultra-thin strip rolling[J]. International Journal of Mechanical Sciences，2017，133：788-793.
[31] LIU X，XIAO H. Theoretical and experimental study on the producible rolling thickness in ultra-thin strip rolling[J]. Journal of Materials Processing Technology，2020，278(116537)：1-9.
[32] 刘晓，付伦，芦跃峰，等. 薄带材轧制的最小可轧厚度理论及数值模拟[J]. 钢铁，2021，56(11)：87-95. LIU Xiao，FU Lun，LU Yuefeng，et al. Theory and numerical simulation of minimum rolling thickness for thin strip rolling[J]. Iron and Steel，2021，56(11)：87-95.
[33] 李伟，李松松，于辉. 基于轧制力判定的薄带材极限可轧厚度理论研究[J/OL]. 工程力学，2023[2023-10-07]. https://link.cnki.net/urlid/11.2595.o3.20230928.1640.014. LI Wei，LI Songsong，YU Hui. Theoretical study on the limit rollable thickness of thin strip based upon rolling force[J/OL]. Engineering Mechanics，2023[2023-10-07]. https://link.cnki.net/urlid/11.2595.o3.20230928.1640.014.
[34] 李伟，于辉，李松松，等. 基于各向异性冷轧纯钛薄带的屈服行为研究[J]. 稀有金属材料与工程，2023，52(9)：3213-3220. LI Wei，YU Hui，LI Songsong，et al. Yield behavior of cold-rolled pure titanium thin strip based on anisotropy[J]. Rare Metal Materials and Engineering，2023，52(9)：3213-3220.

基于各向异性的薄带冷轧变形区接触压力模型研究

Research on Contact Pressure Model of Cold Rolled Deformation Zone of Thin Strip Based on Anisotropy

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	陈鑫, 龚颖颖, 杨立飞. 考虑各向异性和剪切行为的GTN损伤模型及其在成形极限预测中的应用[J]. 机械工程学报, 2025, 61(6): 141-150.
[2]	林艳丽, 王家明, 刘军鹏, 苏一博, 王硕, 何祝斌. 金属薄板杯形件拉深制耳定量预测理论模型[J]. 机械工程学报, 2025, 61(4): 96-106.
[3]	张坤, 白雪山, 孙进, 胡馨予, 林艳丽, 何祝斌. 各向异性屈服准则对铝合金挤压管液压成形仿真精度的影响[J]. 机械工程学报, 2025, 61(4): 167-175.
[4]	郑学斌, 韩龙帅, 李学涛, 鄂宏伟, 吴向东, 万敏. DP780双相钢U弯回弹预测影响因素研究[J]. 机械工程学报, 2024, 60(6): 197-206.
[5]	刘松, 李俊辉, 刘云飞, 计江, 谢维维, 窦锋, 刘江林, 柳宇. 特种合金极薄带轧制工艺与技术装备的研制[J]. 机械工程学报, 2024, 60(4): 357-368.
[6]	李少川, 肖贵坚, 曹华军, 汪迎新, 赵泽勇, 卓晓琴, 黄云. 基于相位调控的二维超声辅助砂带磨削方法及其对GH4169表面完整性研究[J]. 机械工程学报, 2024, 60(21): 349-364.
[7]	张玄, 刘源, 侯耀东, 张承双, 尹维龙, 邓清扬. 考虑几何非线性的正交各向异性层合板随机振动响应数值解[J]. 机械工程学报, 2024, 60(2): 224-233.
[8]	李帅, 楚志兵, 杨博文, 薛春, 拓雷锋. 新型三辊皮尔格曲面构型设计方法及成形效果分析研究[J]. 机械工程学报, 2024, 60(16): 130-140.
[9]	贺炜林, 孟宝, 万敏. GH4169合金超薄带材U形弯曲回弹行为研究[J]. 机械工程学报, 2024, 60(14): 174-184.
[10]	肖蜜, 李奇石, 高亮, 沙伟, 黄明喆. 基于各向异性材料插值的点阵散热结构跨尺度拓扑优化[J]. 机械工程学报, 2024, 60(13): 71-80.
[11]	张广冬, 黄翔. 以制品几何精度为目标的塑料挤出模具优化设计方法[J]. 机械工程学报, 2023, 59(8): 142-150.
[12]	姜晨, 高睿, 郑泽希. GaAs材料解理加工分子动力学分析及工艺实验[J]. 机械工程学报, 2023, 59(5): 317-324.
[13]	张国栋, 张鹏, 高健时, 余槐, 袁鸿, 丁宁, 熊华平. 电子束熔丝增材制造TC11钛合金组织及力学性能[J]. 机械工程学报, 2023, 59(4): 105-112.
[14]	黄庆学. 高品质钢铁板带轧制关键装备与技术研究进展[J]. 机械工程学报, 2023, 59(20): 34-63.
[15]	彭艳, 石宝东, 刘才溢, 邢建康. 板带轧制装备-工艺-产品质量综合控制融合发展综述[J]. 机械工程学报, 2023, 59(20): 96-118.