三光束激光熔覆工艺参数对熔覆层几何特征影响

doi:10.3901/JME.2020.15.227

摘要/Abstract

摘要： 采用“三光束光内同轴送丝”激光熔覆新方法研究可以获得表面质量较高单道熔覆层的工艺参数组合方案。建立三光束激光熔覆工艺参数与熔覆层表面形貌关系以及几何特征变化规律的数学模型，通过激光提供的单位能量密度E₁与丝材所需的能量密度E₂之间比值关系判断熔覆层表面形貌状态，工艺参数和熔覆层几何特征关系的数学模型预测熔覆层几何特征变化规律，并采用单因素试验法进行验证。研究结果如下：E₁/E₂<1，熔池能量“不足”，1.1≥E₁/E₂≥1.0，熔池能量处于“不足”到“充足”过渡阶段，以及E₁/E₂>1.6，熔池能量“过剩”，这三种情况形成的熔覆层表面质量较差；只有当1.5≥E₁/E₂>1.1，熔池能量“充足”能够充分熔化进入熔池的丝材，且丝材能够以连续平稳的“搭桥过渡”方式熔入熔池，熔覆层表面连续光滑，质量较高；熔覆层几何特征变化规律：数学模型预测值变化趋势与试验值基本吻合，离焦量减小，熔覆层宽度W减小，高度H增大，宽高比a减小；激光功率增大，熔覆层宽度W增大，高度H减小，宽高比α增大。扫描速度增大，熔覆层宽度W减少，高度H减少，宽高比a略有增加。送丝速度增大，熔覆层宽度W和高度H都会增大，宽高比α减小。综上采用“三光束光内同轴送丝”新方法对不锈钢304材料的丝材和基材进行激光熔覆试验，工艺参数组合方案满足1.5≥E₁/E₂>1.1，可以制备出表面形貌佳熔覆层。

关键词: 激光熔覆, 三光束, 光内送丝, 工艺参数, 几何特征

Abstract: In order to obtain better combination scheme of process parameters of single cladding layer with high surface quality, a new forming method of “coaxial wire feeding inside three beams” is used. Mathematical model of relationship between process parameters of layer cladding and the surface morphology is established, between process parameters and geometric characteristics. The surface morphology state of cladding layer is judged by the ratio between the unit energy density provided by the laser E₁ and the required energy density of wire E₂.The mathematical model of the relationship between the process parameters and the geometric characteristics of cladding layer is used to predict the variation law of the geometric characteristics, and the single factor test method is used to make experimental verification. The experienced state of cladding layer surfacemorphology is that:E₁/E₂< 1, the molten pool energy is “insufficient”,1.1≥E₁/E₂≥1.0, the energy of molten pool is in the transition stage from “insufficient” to “sufficient”, E₁/E₂> 1.6, the energy of the molten pool is “excess”, the surface quality of the coating formed in these three cases is poor. Only when 1.5≥E₁/E₂>1.1, the “sufficient” energy of the molten pool can fully melt the wire, which can be melted into the molten pool in a continuous and stable way, the surface of cladding layer is continuously smooth and the quality is high. The variation law of cladding layer geometric characteristics: the predicted value of the mathematical model is in good agreement with the experimental value, the defocusing amount decreases, the width W decreases, the height H increases, and the ratio of width to height α decreases. Laser power increases, the width W increases, the height H decreases, and the ratio of width to height α increases. Scanning speed increases, the width W decreases, the height H decreases, and the ratio of width to height α increases slightly. Wire feeding speed increases, the width W and height H increases, and the ratio of width to height α decreases. Conclusion is that: make laser cladding test of stainless steel 304 wire and substrate by using new forming method of “coaxial wire feeding inside three beams”, selecting reasonable process parameters scheme, which meet 1.5≥E₁/E₂>1.1, better surface morphology can be achieved.

Key words: laser cladding, three beams, wire feeding inside beams, process parameter, geometric characteristics

中图分类号:

TN249
TF124

刘凡, 吉绍山, 傅戈雁, 石世宏. 三光束激光熔覆工艺参数对熔覆层几何特征影响[J]. 机械工程学报, 2020, 56(15): 227-237.

LIU Fan, JI Shaoshan, FU Geyan, SHI Shihong. The Influence of Process Parameters on Geometry Characteristics by Three Beams Laser Cladding[J]. Journal of Mechanical Engineering, 2020, 56(15): 227-237.

参考文献

[1] 董世运,马运哲,徐滨士,等. 激光熔覆材料研究现状[J].材料导报,2006,20(6):5-9. DONG Shiyun,MA Yunzhe,XU Binshi,et al. Current status of material for laser cladding[J].Material Review,2006,20(6):5-9.
[2] SYED W H H,LI Lin. Effects of wire feeding direction and location in multiple layer diode laser direct metal deposition[J]. Applied Surface Science,2005,248:518-524.
[3] 石世宏,傅戈雁,李龙,等. 中空激光光内同轴送丝熔覆工艺的实现及其试验研究[J].中国激光,2010,37(1):266-270. SHI Shihong,FU Geyan,LI Long,et al. Realization and research of laser cladding with method of internal wire feeding through a hollow laser beam[J].Chinese Journal of Laser,2010,37(1):266-270.
[4] 朱刚贤,石拓,傅戈雁,等. 中空光光内送丝熔覆工艺参数对熔覆层质量的影响[J]. 应用激光,2013,33(4):381-384. ZHU Gangxian,SHI Tuo,FU Geyan,et al. Effect of process parameters on the quality of the cladding layer by the inside-laser wire feeding[J]. Applied Laser,2013,33(4):381-384.
[5] LIU Shuang,LIU Wei,HAROONI M,et al. Real-time monitoring of laser hot-wire cladding of Inconel 625[J]. Optics and Laser Technology,2014,62:124-134.
[6] SHI Jianjun,ZHU Ping,FU Geyan,et al. Geometry characteristics modeling and process optimization in coaxial laser inside wire cladding[J]. Optics and Laser Technology,2018,101:341-348.
[7] 傅戈雁,吉绍山,石世宏,等. 一种用于激光熔覆的激光光内送丝装置:CN201610075735[P]. 2017-09-05. FU Geyan,JI Shaoshao,SHI Shihong,et al. A device of coaxial wire feeding through beams for laser cladding:CN201610075735[P]. 2017-09-05.
[8] 傅戈雁,吉绍山,刘凡,等. 激光熔覆装置的抛物面的设定方法及激光熔覆装置:CN201710662057.1[P]. 2019-04-12. FU Geyan,JI Shaoshao,LIU Fan,et al. Setting method of parabola of laser cladding device and laser cladding device:CN201710662057.1[P]. 2019-04-12.
[9] 傅戈雁,吉绍山,刘凡,等.激光熔覆装置:CN201710661517.9[P]. 2017-09-29. FU Geyan,JI Shaoshao,LIU Fan,et al. Laser cladding device:CN201710661517.9[P]. 2017-09-29.
[10] 傅戈雁,吉绍山,刘凡,等.激光熔覆装置:CN201710661537.6[P]. 2017-10-03. FU Geyan,JI Shaoshao,LIU Fan,et al. Laser cladding device:CN201710661537.6[P]. 2017-10-03.
[11] 李凯斌,李东,刘东宇,等. 光纤激光送丝熔覆修复工艺研究[J]. 中国激光,2014,41(11):76-81. LI Kaibin,LI Dong,LIU Dongyu,et al. Research of fiber laser cladding repairing process with wire feeding[J]. Chinese Journal of Laser,2014,41(11):76-81.
[12] 罗园青. 基于送丝熔敷的激光成形技术研究[D]. 武汉:华中科技大学,2016. LUO Yuanqing. Study on laser wire-melting deposition technology[D]. Wuhan:Huazhong University of Science and Technology,2016.
[13] MOK S,BI G,FOLKES J,et al. Deposition of Ti-6Al-4V using a higher power diode laser and wire,partI:Investigation on the process characteristics[J]. Surface & Coating Technology,2008,202:3933-3939.
[14] ABIOYE TE,FOLKES J,CLARE A T. A parametric study of inconel 625 wire laser deposition[J]. Journal of Material Processing Technology,2013,213:2145-2151.
[15] LIU Shuang,LIU Wei,KOVACEVIC R. Experimental investigation of laser hot-wire cladding[J]. Institution of Mechanical Engineers,2015:1-14.
[16] BARROI A,GONCALVES D,HERMSDORF J,et al. Influence of laser power on the shape of single tracks in scanner based laser wire cladding[J]. Physics Procedia.,2016:667-673.
[17] WEN Peng,SHAN Jiguo,ZHENG Shiqing,et al. Control of wire transfer behaviors in hot wire laser welding[J]. Int. J. Adv. Manuf. Technol.,2015:1-10.
[18] 吉绍山,刘凡,傅戈雁,等. 三光束光内同轴送丝激光熔覆成形新方法研究[J]. 表面技术,2019,48(4):287-289. JI Shaoshan,LIU Fan,FU Geyan,et al. New forming method of coaxial wire feeding inside three beams laser cladding[J]. Surface Technology,2019,48(4):287-289.
[19] 雷定中,石世宏,傅戈雁. 宽带激光内送粉熔覆工艺研究[J].中国激光,2015,42(11):1-8. LEI Dingzhong,SHI Shihong,FU Geyan. Research of hollow broadband laser cladding method[J].Chinese Journal of Laser,2015,42(11):1-8.
[20] 曹明翠,郑启光. 激光热加工[M]. 武汉:华中工学院出版社,1995. CAO Mingcui,ZHENG Qiguang. Laser hot working[M]. Wuhan:Huazhong Institute of Technology Press,1995.
[21] 吴宗凡,柳美琳,张绍举. 红外与微光技术[M]. 北京:国防工业出版社,1998. WU Zongfan,LIU Meilin,ZHANG Shaoju. Infrared and low light technology[M]. Beijing:National Defense Industry Press,1998.
[22] 黄伟. 涡扇发动机排气系统红外特征计算与抑制技术研究[D]. 南京:南京航空航天大学,2010. HUANG Wei. Investigation of numerical calculation of IR characteristics and stealth technology of turbofan engine exhaust system[D]. Nanjing:Nanjing University of Aeronautics and Astronautics,2010.
[23] VASINONTA A,BEUTH J L,GRIFFITH M L. A process map for consistent build conditions in the solid freeform fabrication of thin-walled structures[J]. Journal of Manufacturing Science & Engineering,2001,123(4):615-622.
[24] SUAREZ A,AMADO J,TOBAR M,et al. Study of residual stresses generated inside laser cladded plates using FEM and diffraction of synchrotron radiation[J]. Surf. Coat. Tech.,2010,204(12-13):1983-1988.
[25] 刘建强.304不锈钢激光焊接的建模与仿真[D].天津:天津大学,2004. LIU Jianqiang. Modeling and simulating of laser welding for stainless steel 304[D].Tianjin:Tianjin University,2004.
[26] 高燕.不锈钢激光焊接热源及过程的模拟与仿真[D].天津:天津大学,2006. GAO Yan. The simulation of heat source and process in laser welding for stainless steel[D].Tianjin:Tianjin University,2006.
[27] PAUL S,SINGH R,YAN W. Thermal model foradditive restoration of mold steels using crucible steel[J]. Journal of Manufacturing Processes,2016,24:346-354.
[28] STEEN WM,WEERASINGHE VM,MONSON P. Some aspects of the formation of laser clad tracks[J]. SPIE, 1986,650:226-234.