丙烷压力对超声速微粒沉积铝青铜涂层组织和性能的影响

doi:10.3901/JME.2016.08.119

摘要/Abstract

摘要： 采用超声速微粒沉积技术在不同丙烷压力(0.469 MPa,0.496 MPa,0.524 MPa,0.551 MPa)条件下制备4种铝青铜涂层,采用环境扫描电子显微镜、X射线衍射仪、能谱仪等试验仪器表征涂层的微观组织、相结构以及氧元素质量分数等,运用显微硬度仪、拉伸试验机和CETR摩擦磨损试验机等试验设备分析涂层的力学性能和摩擦学性能。结果表明,丙烷压力对涂层组织结构及力学性能有显著的影响,随着丙烷压力的升高,涂层孔隙率与氧元素质量分数呈负相关关系,在丙烷压力为0.524 MPa时,涂层孔隙率为0.8%,氧元素质量分数为0.97%,更接近其平衡点;丙烷压力为0.524 MPa以下时,涂层较原始粉末物相无明显变化,主要仍为α+β'+K相;涂层显微硬度、结合强度及耐磨性能随丙烷压力的升高均呈先增大后减小的趋势变化,丙烷压力为0.524 MPa时,涂层的力学性能和耐磨性能达到最优。

关键词: 丙烷压力, 铝青铜涂层, 涂层性能

Abstract: Four kinds of aluminum bronze coatings are fabricated by supersonic particles deposition (SPD) method under different propane pressure (0.469 MPa, 0.496 MPa, 0.524 MPa, 0.551 MPa). The microstructure, phase structure and oxygen content of coating are analyzed by scanning electron microscope (SEM), X-ray diffraction (XRD) and energy dispersive spectrometer (EDS). The mechanical properties are tested on a tensile testing machine and a hardness tester. The wear resistance properties are investigated by CETR wear tester. The results show that propane pressure has a significant effect on microstructure, mechanical properties and wear resistance properties. With the increase of propane pressure, porosity and oxygen content of coating are negatively correlated. The coating with propane pressure 0.524 MPa has relatively superior porosity (0.8%) and oxygen mass fraction (0.97%), which closes to balance between porosity and oxygen content. All the spray power and coatings are composed of α, β' and K phase, when the propane pressure is lower 0.524 MPa. The average hardness, adhesive strength and wearing capacity of the coating shows a first increases and then decreases trend, with the increase of propane pressure. The mechanical properties and wear resistance properties of aluminum bronze coatings fabricated by SPD with propane pressure 0.524 MPa are optimal respectively.

Key words: aluminum bronze coating, coating properties, propane pressure

中图分类号:

TG156

朱胜, 周超极, 王晓明, 张垚, 韩冰源. 丙烷压力对超声速微粒沉积铝青铜涂层组织和性能的影响[J]. 机械工程学报, 2016, 52(8): 119-124.

ZHU Sheng, ZHOU Chaoji, WANG Xiaoming, ZHANG Yao, HAN Bingyuan. Influence of Propane Pressure on Microstructure and Properties of Supersonic Particles Deposition Aluminum Bronze Coatings[J]. Journal of Mechanical Engineering, 2016, 52(8): 119-124.

参考文献

[1] 徐建林,陈超,喇培清,等. 新型铸造铝青铜的润滑摩擦性能[J]. 中国有色金属学报,2004,14(6)：917-921.
XU Jianlin, CHEN Chao, LA Peiqing, et al. Lubrication friction performance of new as-cast aluminum bronze[J]. The Chinese Journal of Nonferrous Metals,2004,14(6)：917-921.
[2] ALAM S,SASAKI S,SHIMURA H. Friction and wear characteristics of aluminum bronze coatings on steel substrates sprayed by a low pressure plasma technique[J]. Wear,2001,248(1)：75-81.
[3] 路阳,袁利华,李文生,等. 高铝青铜Cu-14%Al-X合金在3.5%NaCl溶液中的腐蚀性能[J]. 机械工程学报,2005,41(9)：42-45.
LU Yang,YUAN Lihua,LI Wensheng,et al. Corrosion resistance of Cu-14%Al-X Al-Bronze alloy in 3.5% NaCl solution[J]. Chinese Journal of Mechanical Engineering,2005,41(9)：42-45.
[4] 施立新,李强. 雾化压力对冷却速率及冷却时间影响的定量分析[J]. 计算机与应用化学,2013,30(4)：431-434.
SHI Lixin,LI Qiang. Quantitative analysis of the effect of atomization pressure on the cooling rate and cooling time[J]. Computers and Applied Chemistry,2013,30(4)：431-434.
[5] 张忠礼,李德元,张楠楠,等. 电弧喷涂铝青铜复合涂层的抗高温氧化作用与机理[J]. 焊接学报,2006,27(4)：85-88.
ZHANG Zhongli,LI Deyuan,ZHANG Nannan,et al. High temperature oxidation behavior of arc sprayed duplex aluminum bronze based coating[J]. Transaction of the China Welding Institution,2006,27(4)：85-88.
[6] 路阳,郭文俊,杨效田,等. 粒度对超音速等离子喷涂高铝青铜合金微观结构的影响[J]. 功能材料,2013,44(18)：2684-2687.
LU Yang,GUO Wenjun,YANG Xiaotian,et al. Study on synthesis,characterization and mechanism of carboxylated collagen fiber[J]. Functional Materials,2013,44(18)：2684-2687.
[7] 许艺鸣,单春贤,唐爱坤,等. 微型燃烧器内掺氢甲烷燃烧特征的数值模拟[J]. 机械工程学报,2015,51(18)：151-157.
XU Yiming,SHAN Chunxian,TANG Aikun,et al. Numerical simulation of methane combustion characteristics with hydrogen addition in a micro-combustor[J]. Journal of Mechanical Engineering,2015,51(18)：151-157.
[8] 朱胜,刘玉项,王晓明,等. 氢气流量对超音速微粒沉积Al-12Si涂层的影响[J]. 中国有色金属学报,2014,24(6)：1504-1509.
ZHU Sheng,LIU Yuxiang,WANG Xiaoming,et al. Effect of hydrogen flow rate on Al-12Si coating by supersonic particles deposition[J]. The Chinese Journal of Nonferrous Metals,2014,24(6)：1504-1509.
[9] 陈书赢,王海斗,徐滨士,等. 基于分形理论的超音速等离子喷涂层界面结合行为研究[J]. 物理学报,2014,63(15)：328-334.
CHEN Shuying,WANG Haidou,XU Binshi,et al. Investigation on the bonding behavior of the interface within the supersonic plasma sprayed coating system based on the fractal theory[J]. Acta Physica Sinica,2014,63(15)：328-334.
[10] COSTA M L,de ALMEIDA S F M,REZENDE M C. The influence of porosity on the interlaminar shear strength of carbon/epoxy and carbon/bismaleimide fabric laminates[J]. Composites Science and Technology,2001,61(14)：2101-2108.
[11] MOLAK R M,ARAKI H,WATANABE M,et al. Warm spray forming of Ti-6Al-4V[J]. Journal of Thermal Spray Technology,2014,23(1-2)：197-212.
[12] ALTOMARE L,BELLUCCI D,BOLELLI G,et al. Microstructure and in vitro behaviour of 45S5 bioglass coatings deposited by high velocity suspension flame spraying (HVSFS)[J]. Journal of Materials Science：Materials in Medicine,2011,22(5)：1303-1319.
[13] 王铁钢,宋丙红,华伟刚,等. 工艺参数对爆炸喷涂WC-Co涂层性能均匀性的影响[J]. 金属学报,2011,47(1)：115-122.
WANG Tiegang,SONG Binghong,HUA Weigang,et al. Influence of process parameters on the performance uniformity of detonation gun sprayed WC-Co coatings [J]. Acta Metallurgica Sinica,2011,47(1)：115-122.

[1]	方续东, 邓武彬, 吴祖堂, 李进, 吴晨, 前田龙太郎, 田边, 赵立波, 林启敬, 张仲恺, 韩香广, 蒋庄德. 基于惯性传感器的呼吸测量技术综述[J]. 机械工程学报, 2024, 60(20): 1-23.
[2]	傅杨, 张跃, 毛颖, 唐小华, 陈祖高, 徐和武, 杨雨沛, 高斌, 田贵云. 基于Feature Boosting的管道电磁内检测多传感信号缺陷解析算法[J]. 机械工程学报, 2024, 60(20): 51-67.
[3]	吴洁, 沈以赴, 黄国强. 2024铝合金填丝TIG焊接头搅拌摩擦加工组织和性能研究[J]. 机械工程学报, 2024, 60(20): 153-161.
[4]	张志勇, 王宇翔, 黄彩霞, 吴悠, 杜荣华. 融合灰色预测和卡尔曼滤波的车辆侧向碰撞预警[J]. 机械工程学报, 2024, 60(20): 240-250.
[5]	廖贵文, 张毅, 魏凯, 刘小君, 王伟. 受限润滑界面液固二相流场结构与颗粒运动行为耦合特性分析[J]. 机械工程学报, 2024, 60(20): 351-360.
[6]	王旭, 姜兴宇, 杨国哲, 孙猛, 于沈弘, 毕凯航, 赵日铮, 刘伟军. 基于PSO-SSA的激光清洗装备人机界面布局优化研究[J]. 机械工程学报, 2024, 60(20): 372-387.
[7]	王德祥, 张宇, 江京亮, 刘新福, 刘国梁. 离子液基和棕榈油基纳米流体在镍基高温合金微量润滑磨削界面的摩擦学机理研究[J]. 机械工程学报, 2024, 60(19): 159-171.
[8]	李浦, 逯代兴. 协同仿真算法研究综述[J]. 机械工程学报, 2024, 60(19): 172-186.
[9]	王晓宇, 魏兆成, 王学勤, 王栋. 整体叶轮双列开槽五轴插铣加工的残留材料建模[J]. 机械工程学报, 2024, 60(19): 310-317.
[10]	王高见, 刘丽, 康丹丹, 叶延洪, 邓德安. Ni含量对高速列车转向架耐候钢焊缝金属微观组织、力学性能及腐蚀行为的影响[J]. 机械工程学报, 2024, 60(18): 163-172.
[11]	张明康, 师文庆, 徐梅珍, 王迪, 陈杰. 隐式曲面多孔结构压缩性能与流体压降性能研究[J]. 机械工程学报, 2024, 60(18): 394-406.
[12]	马伟佳, 朱小龙, 刘青瑶, 段星光, 李长胜. 人工智能在机器人辅助手术中的应用[J]. 机械工程学报, 2024, 60(17): 22-39.
[13]	袁小庆, 吴涛, 原勋, 王文东. 基于GSO-RF意图识别算法的全身助力外骨骼控制方法研究[J]. 机械工程学报, 2024, 60(17): 91-101.
[14]	张禹泽, 赵竞夫, 赵振伟, 康荣杰, 戴建生, 宋智斌. 面向多关节训练的并联柔索驱动下肢康复机器人设计与分析[J]. 机械工程学报, 2024, 60(17): 111-122.
[15]	梁旭, 张建勇, 李国涛, 苏婷婷, 何广平, 侯增广. 面向骨折复位手术的冗余并联机构：设计、建模与性能分析[J]. 机械工程学报, 2024, 60(17): 133-146.