Deployment Dynamic Modelling and Adaptive Robust Control of Truss-shaped Deployable Grasping Mechanism

doi:10.3901/JME.2020.05.039

Abstract

Abstract: A dynamic modeling method for the deployment motion of a new type of truss-shaped deployable grasping mechanism is proposed, and a control strategy considering nonlinear factors, such as over-constraints, is designed to improve the motion performance. The truss-shaped deployable grasping mechanism is briefly introduced, and the dynamic model of the deployment motion of the mechanism is established by using Lagrangian mechanics and the recursive method. Using the known information of the dynamic model, an extended state observer is designed to estimate the dynamic part caused by the over-constraints in the mechanism. An improved adaptive robust controller based on extended state observer is proposed, where the inertia parameter of the mechanism is estimated by a discontinuous-projection-based adaptive control law, and the problem of the traditional adaptive robust controller is overcome by proposing an adaptive sliding mode control law. The experimental platform of deployable grasping mechanism is built, and the effectiveness of the proposed controller is verified in comparison with the existing state-of-the-art controllers.

Key words: deployable mechanism, over-constraint, dynamic modelling, extended state observer, adaptive robust control

CLC Number:

TH113

LI Guotao, LI Bing, GUO Hongwei, HUANG Hailin. Deployment Dynamic Modelling and Adaptive Robust Control of Truss-shaped Deployable Grasping Mechanism[J]. Journal of Mechanical Engineering, 2020, 56(5): 39-46.

References

[1] GREBENSTEIN M,CHALON M,FRIEDL W,et al. The hand of the DLR hand arm system:Designed for interaction[J]. International Journal of Robotics Research,2012,31(13):1531-1555.
[2] LI Changsheng,GU Xiaoyi,REN Hongliang. A cable driven flexible robotic grasper with lego-like modular and reconfigurable joints[J]. IEEE/ASME Transaction on Mechatronics,2017,22(6):2757-2767.
[3] FIROUZEH A,PAIK J. Grasp mode and compliance control of an under-actuated origami gripper using adjustable stiffness joints[J]. IEEE/ASME Transaction on Mechatronics,2017,22(5):2165-2773.
[4] WANG Congzhe,FANG Yuefa,GUO Sheng. Multi-objective optimization of a parallel ankle rehabilitation robot using modified differential evolution algorithm[J]. Chinese Journal of Mechanical Engineering,2015,28(4):702-715
[5] QI Xiaozhi,HUANG Hailin,MIAO Zhihuai,et al. Design and mobility analysis of large deployable mechanisms based on plane-symmetric bricard linkage[J]. Transactions of the ASME:Journal of Mechanical Design,2016,139(2):022302.
[6] ZENG Qiang,FANG Yuefa. Structural synthesis and analysis of serial-parallel hybrid mechanisms with spatial multi-loop kinematic chains[J]. Mechanism and Machine Theory,2012,49(3):198-215.
[7] JIA Guanglu,HUANG Hailin,LI Bing,et al. Synthesis of a novel type of metamorphic mechanism module for large scale deployable grasping manipulators[J]. Mechanism and Machine Theory,2018,128:544-559.
[8] LI Guotao,HUANG Hailin,GUO Hongwei,et al. Dynamic modeling and control for a deployable grasping manipulator[J]. IEEE Access,2019,7:23000-23011.
[9] LI Guotao,HUANG Hailin,GUO Hongwei,et al. Design,analysis and control of a novel deployable grasping manipulator[J]. Mechanism and Machine Theory, 2019,138:182-204.
[10] LIU Wenlan,XU Yundou,YAO Jiantao,et al. Methods for force analysis of overconstrained parallel mechanisms:A review[J]. Chinese Journal of Mechanical Engineering,2017,30(6):1460-1472.
[11] 王向阳,郭盛,曲海波,等. 并联机构驱动力优化配置方法及应用研究[J]. 机械工程学报,2019,55(1):32-41. WANG Xiangyang,GUO Sheng,QU Haibo,et al. Force analysis of lower-mobility parallel mechanisms with over-constrained couples[J]. Journal of Mechanical Engineering,2019,55(1):32-41.
[12] XU Yundou,LIU Wenlan,YAO Jiantao,et al. A method for force analysis of the overconstrained lower mobility parallel mechanism[J]. Mechanism and Machine Theory,2015,88:31-48.
[13] 赵燕,黄真. 含过约束力偶的少自由度并联机构的受力分析[J]. 机械工程学报,2010,46(5):15-21. ZHAO Yan,HUANG Zhen. Force analysis of lower-mobility parallel mechanisms with over-constrained couples[J]. Journal of Mechanical Engineering,2010,46(5):15-21.
[14] HAN Jingqing. From PID to active disturbance rejection control[J]. IEEE Transaction on Industrial Electronics,2009,56(3):900-906.
[15] 韩京清. 从PID技术到"自抗扰控制"技术[J]. 控制工程,2002,9(3):13-18. HAN Jingqing. From PID technique to active disturbances rejection control technique[J]. Control Engineering of China,2002,9(3):13-18.
[16] LI Guotao,XU Wenfu,ZHAO Jianguo,et al. Precise robust adaptive dynamic surface control of permanent magnet synchronous motor based on extended state observer[J]. IET Science Measurement and Technology,2017,11(5):590-599.
[17] YAO Bin,BU Fanping,REEDY J,et al. Adaptive robust motion control of single-rod hydraulic actuators:Theory and experiments[J]. IEEE/ASME Transaction on Mechatronics,2000,5(1):79-91.
[18] YAO Jianyong,JIAO Zongxia,MA Dawei. Adaptive robust control of DC motors with extended state observer[J]. IEEE Transaction on Industrial Electronics,2014,61(7):3630-3637.
[19] YAO Jianyong,DENG Wenxiang,JIAO Zongxia. Adaptive control of hydraulic actuators with LuGre model-Based friction compensation[J]. IEEE Transactions on Industrial Electronics,2015,62(10):6469-6477.
[20] ZHENG Qing,GAO L Q,GAO Zhiqing. On stability analysis of active disturbance rejection control for nonlinear time-varying plants with unknown dynamics[C]//The 46th IEEE Conference on Decision and Control,December 12-14,2007,New Orleans,LA,USA. New York:IEEE,2008:3501-3506.
[21] XU Li,YAO Bin. Adaptive robust precision motion control of linear motors with negligible electrical dynamics:Theory and experiments[J]. IEEE/ASME Transactions on Mechatronics,2001,6(4):444-452.
[22] GOODWIN G C,MAYNE D Q. A parameter estimation perspective of continuous time model reference adaptive control[J]. Automatica,1987,23(1):57-70.
[23] NA Jing,CHEN Qiang,REN Xuemei,et al. Adaptive prescribed performance motion control of servo mechanisms with friction compensation[J]. IEEE Transaction on Industrial Electronics,2014,61(1):486-494.