基于纵向模态超声导波陷频特性的钢绞线拉力测量新方法

doi:10.3901/JME.2016.12.009

机械工程学报 ›› 2016, Vol. 52 ›› Issue (12): 9-15.doi: 10.3901/JME.2016.12.009

扫码分享

基于纵向模态超声导波陷频特性的钢绞线拉力测量新方法

吴斌¹, 张瑞芳¹, 刘秀成¹, 曹海洋¹, 韩强², 何存富¹

1. 北京工业大学机械工程与应用电子技术学院北京 100124;
2. 华南理工大学土木与交通学院广州 510641

出版日期:2016-06-15 发布日期:2016-06-15
作者简介:吴斌,男,1962年出生,教授,博士研究生导师。主要研究方向为工程波动力学及无损检测新技术。E-mail：wb@bjut.edu.cn;张瑞芳,女,1991年出生,主要研究方向为超声无损检测方法与技术。E-mail：zhangruifang@emails.bjut.edu.cn;刘秀成(通信作者),男,1984年出生,博士。主要研究方向为电磁声学传感器技术。E-mail：xiuchengliu@bjut.edu.cn
基金资助:
国家自然科学基金(11132002,11402008)、北京市自然科学基金(3154030)和中国博士后科学基金(2014M560029)资助项目

Innovative Method for Measuring Tensile Force Based on the Notch Frequency Property of Longitudinal Guided Wave in Steel Strand

WU Bin¹, ZHANG Ruifang¹, LIU Xiucheng¹, CAO Haiyang¹, HAN Qiang², HE Cunfu¹

1. College of Mechanical Engineering and Applied Electronics Technology, Beijing University of Technology, Beijing 100124;
2. School of Civil Engineering and Transportation, South China University of Technology, Guangzhou 510641

Online:2016-06-15 Published:2016-06-15

摘要/Abstract

摘要： 试验发现了钢绞线结构中L(0,1)模态导波存在陷频这一固有声学特性,由此提出一种钢绞线拉力检测新方法。为测试钢绞线中导波陷频特性与拉力的关系,研制了一款柔性低频磁致伸缩传感器,可在30~160 kHz范围内激励/接收L(0,1)模态导波。在直径17.8 mm和15.2 mm的两种7芯钢绞线上进行导波陷频检测试验,结果表明陷频特征频率与拉力的自然对数值呈良好线性关系,陷频旁侧峰值比随拉力增大而线性增加。试验中1 kN的拉力增量(应力增量约3 MPa)引起的声学参数(陷频特征频率和陷频旁侧峰值比)变化可被检测到并较好的符合标定关系方程。在额定工作载荷内,拉力估算相对误差小于1.5%,这表明新方法具有较高的拉力检测精度。同时,依据试验所得结论,给出了钢绞线结构中L(0,1)模态导波陷频中心频率与拉力关系的修正公式。新方法实施过程简洁,具有很好的工程应用前景。

关键词: 超声导波, 钢绞线, 拉力测量, 陷频特性, 纵向模态

Abstract: An innovative method is presented for tensile force measurement based on the notch frequency property which is a inherent character of longitudinal guided wave in strands. To test the relation between notch frequency and tension in different strands, a flexible low frequency transducer is designed, which can excite/receive L(0,1) mode guided wave in a frequency range of 30 kHz to 160 kHz. Notch frequency property is tested on two strands with different diameters of 17.8 mm and 15.2 mm respectively, and the characteristic frequency is found to be linear to the Napierian logarithm of tension and the ratio of two side peak of the notch frequency is improved linearly by increasing the tension. The change of acoustic characteristic parameter including the characteristic frequency and the ratio of two side peak caused by 1 kN tension increment corresponding to 3 MPa stress increment can be detected, and the change conform to the calibration relationship equations. Within the rated working load scope, the relative error of tension estimation is less than 1.5%, so that the presented method can be applied for highly precise tensile force measurement. According to the experimental conclusion, a modifier formulas of the center notch frequency of L(0,1) mode guided wave connected with tension in strands is obtained. The innovative method is easy to operate, and therefore it has good prospects for engineering applications.

Key words: guided wave, longitudinal mode, notch frequency property, strand, tension measurement

中图分类号:

TH823

吴斌, 张瑞芳, 刘秀成, 曹海洋, 韩强, 何存富. 基于纵向模态超声导波陷频特性的钢绞线拉力测量新方法[J]. 机械工程学报, 2016, 52(12): 9-15.

WU Bin, ZHANG Ruifang, LIU Xiucheng, CAO Haiyang, HAN Qiang, HE Cunfu. Innovative Method for Measuring Tensile Force Based on the Notch Frequency Property of Longitudinal Guided Wave in Steel Strand[J]. Journal of Mechanical Engineering, 2016, 52(12): 9-15.

参考文献

[1] 姜建山,唐德东,周建庭. 桥梁索力测量方法与发展趋势[J]. 重庆交通大学学报,2008,27(3)：379-382, 466.
JIANG Jianshan, TANG Dedong, ZHOU Jianting. Progress and developing trend of cable stress measuring methods of bridge[J]. Journal of Chongqing Jiaotong University,2008,27(3)：379-382, 466.
[2] 李鸣华,吕振洪,余水宝. 钢索张力智能检测仪的设计[J]. 仪器仪表学报, 2001(22)：143-145.
LI Minghua,LÜ Zhenhong,YU Shuibao. Design of intelligent measuring instrument of steel-dragline’s force[J]. Chinese Journal of Scientific Instrument,2001(22)：143-145.
[3] 郝超,裴岷山,强士中. 斜拉桥索力测试新方法——磁通量法[J]. 公路,2000(11)：30-31.
HAO Chao,PEI Minshan,QIANG Shizhong. Magnetic flux method-A new method to test the force of cable in cable-stayed bridge[J]. Highway,2000(11)：30-31.
[4] KWUN H. The magnetostrictive sensor technology for long range guided wave testing and monitoring of structures[J]. Materials Evaluation, 2003, 61(1)：80-84.
[5] XU Jiang, WU Xinjun,WANG Liangyun, et al. Detecting the flaws in prestressing strands using guided waves based on the magnetostrictive effect[J]. Insight - Non-Destructive Testing and Condition Monitoring,2007,49(11)：647-650.
[6] 刘增华,张易农,张慧昕,等. 基于磁致伸缩效应在钢绞线中激励接收纵向导波模态的试验研究[J]. 机械工程学报,2010,46(6)：71-76.
LIU Zenghua, ZHANG Yinong, ZHANG Huixin, et al. Experimental research on excitation and reception of longitudinal guided wave modes in steel strands based on magnetostrictive effect[J]. Journal of Mechanical Engin eering, 2010,46(6)：71-76.
[7] CHAKI S, BOURSE G. Stress level measurement in prestressed steel strands using acoustoelastic effect[J]. Experimental Mechanics,2009,49(5)：673-681.
[8] RIZZO P, SCALEA F L D. Monitoring steel strands via ultrasonic measurements[J]. Proceedings of Spie,2002 (4696)：62-73.
[9] LIU Yijie, HAN Qiang,LI Chunlei,et al. Numerical investigation of dispersion relations for helical waveguides using the scaled boundary finite element method[J]. Journal of Sound and Vibration,2014,333(7)：1991-2002.
[10] KWUN H, BARTELS K A, HANLEY J J. Effects of tensile loading on the properties of elastic-wave propagation in a strand [J]. Journal of the Acoustical Society of America,1998,103(6)：3370-3375.
[11] TREYSSÈDE F, LAGUERRE L. Investigation of elastic modes propagating in multi-wire helical waveguides[J]. Journal of Sound & Vibration,2010,329(10)：1702-1716.
[12] TREYSSÈDE F, FRIKHA A, CARTRAUD P. Mechanical modeling of helical structures accounting for translational invariance. Part 2：Guided wave propagation under axial loads[J]. International Journal of Solids & Structures,2013,50(9)：1383-1393.
[13] BARTOLI A I, CASTELLAZZI G, MARZANI A,et al. Prediction of stress waves propagation in progressively loaded seven wire strands[J]. Proceedings of SPIE - The International Society for Optical Engineering,2012,8345：834505-834505-12.
[14] BARTOLI I, SALAMONE S, PHILLIPS R, et al. Use of interwire ultrasonic leakage to quantify loss of prestress in multiwire tendons[J]. Journal of Engineering Mechanics,2014,137(5)：324-333.

[1]	周建熹, 林金帆, 洪晓斌, 杨定民. 承力索可调节力压电式阵列超声导波传感器设计与损伤检测[J]. 机械工程学报, 2024, 60(14): 42-50.
[2]	廖林, 袁懋诞, 纪轩荣, 戴安帮. 钢轨中高频超声导波单模态激励技术研究[J]. 机械工程学报, 2021, 57(18): 23-31.
[3]	周澄, 邓菲, 刘尧, 刘秀成, 陈洪磊, 刘增华. 基于神经网络和支持向量机的导波弯管腐蚀损伤程度辨识研究[J]. 机械工程学报, 2021, 57(12): 136-144.
[4]	杨斌, 胡超杰, 轩福贞, 罗承强, 项延训, 肖飚. 基于超声导波的压力容器健康监测I：波传导行为及损伤定位[J]. 机械工程学报, 2020, 56(4): 1-10.
[5]	朱新杰, 邓明晰, 蔡淑娟, 蒋亮, 王睿鹏. 板中超声导波弧形合成孔径阵列多帧满秩成像检测[J]. 机械工程学报, 2020, 56(24): 24-30.
[6]	杨斌, 胡超杰, 轩福贞, 肖飚, 项延训, 罗承强. 基于超声导波的压力容器健康监测III：纤维缠绕压力容器的在线监测[J]. 机械工程学报, 2020, 56(10): 19-26.
[7]	蔡瑞, 李勇, 刘天浩, 裴翠祥, 陈振茂. 金属小径管损伤电磁超声导波检测的高效混合仿真方法及导波换能器可行性研究[J]. 机械工程学报, 2020, 56(10): 34-41.
[8]	周进节, 郑阳, 张宗健, 谭继东. 基于电磁超声换能器阵列的管道螺旋导波传播规律研究[J]. 机械工程学报, 2018, 54(22): 38-46.
[9]	朱新杰, 邓明晰, 都东, 韩赞东. 接收孔径对超声导波合成孔径阵列成像检测的影响分析[J]. 机械工程学报, 2018, 54(12): 133-140.
[10]	王悦民, 邓文力, 耿海泉, 陈乐, 叶伟. 超声导波激励频率选取对其模式控制的影响[J]. 机械工程学报, 2017, 53(24): 104-109.
[11]	伍文君, 章林柯, 王悦民. 基于导波频散特征的超声导波模态识别方法[J]. 机械工程学报, 2017, 53(18): 10-17.
[12]	周进节, 郑阳, 张宗健, 谭继东. 电磁超声导波大功率激励信号的线性放大方法[J]. 机械工程学报, 2017, 53(18): 26-34.
[13]	周进节, 郑阳, 杨齐, 张宗健. 管道超声导波分段时间反转检测方法研究[J]. 机械工程学报, 2017, 53(12): 78-86.
[14]	刘秀成, 徐秀, 吴斌, 高博, 何存富. 多杆系统中导波能量传递特性试验研究[J]. 机械工程学报, 2016, 52(3): 56-62.
[15]	邓菲, 刘洋, 诸葛霞, 黄晶. 变化环境下的超声导波结构健康监测研究进展^*[J]. 机械工程学报, 2016, 52(18): 1-7.

基于纵向模态超声导波陷频特性的钢绞线拉力测量新方法

Innovative Method for Measuring Tensile Force Based on the Notch Frequency Property of Longitudinal Guided Wave in Steel Strand

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价