• CN:11-2187/TH
  • ISSN:0577-6686

机械工程学报 ›› 2017, Vol. 53 ›› Issue (8): 58-67.doi: 10.3901/JME.2017.08.058

• • 上一篇    下一篇

扫码分享

耐热合金钢P91热变形过程静态及亚动态再结晶行为

贾璐1,2, 李永堂1,2, 李振晓1,2   

  1. 1. 太原科技大学材料科学与工程学院 太原 030024;
    2. 太原科技大学金属材料成性理论与技术山西省重点实验室 太原 030024
  • 出版日期:2017-04-15 发布日期:2017-04-15
  • 作者简介:

    贾璐,女,1989年出生,博士研究生。主要研究方向为材料先进制造技术。

    E-mail:jialu19890812@126.com

    李永堂(通信作者),男,1957年出生,博士,教授,博士研究生导师。主要研究方向为锻压设备、材料先进制造技术。

    E-mail:liyongtang@tyust.edu.cn

  • 基金资助:
    * 山西省回国留学人员科研(2015-086)和国家自然科学基金(51135007,51675361)资助项目; 20160612收到初稿,20161205收到修改稿;

Static and Metadynamic Recrystallization Behaviors of Heat-resistant P91 Alloy during Hot Deformation

JIA Lu1,2, LI Yongtang1,2, LI Zhenxiao1,2   

  1. 1. School of Materials Science and Engineering, Taiyuan University of Science and Technology, Taiyuan 030024;
    2. Shanxi Key Laboratory of Metal Forming Theory and Technology, Taiyuan University of Science and Technology, Taiyuan 030024
  • Online:2017-04-15 Published:2017-04-15

摘要:

利用单道次、双道次热压缩试验研究铸态P91合金钢在热变形后的动态、静态、亚动态再结晶行为,探索不同变形温度、应变速率、变形量对静态、亚动态再结晶的影响并建立静态、亚动态再结晶动力学方程。研究得出:热变形结束后,静态再结晶率随变形温度、变形量及应变速率的增大而增大;亚动态再结晶率与变形温度、变形量和应变速率呈单调递增,并最终趋于稳定。以真应变为参数,铸态P91热变形后再结晶类型可按照真应变分为三种情况:当ε<εc时,道次间隔主要发生静态再结晶;当εc<ε<εT时,同时发生静态、亚动态再结晶;当ε>εT时,主要发生亚动态再结晶。通过对双道次压缩试样的显微组织分析得出:相同变形条件下,亚动态再结晶晶粒比静态再结晶细小,再结晶晶粒随变形温度增加而增大,随应变速率增大而减小。

关键词: 大口径厚壁管, 静态再结晶, 热变形, 亚动态再结晶, 真应变, 耐热合金钢

Abstract:

Dynamic, static and metadynamic recrystallization of as-cast P91 alloy steel are investigated through single and double-hit unidirectional thermal compression experiments under different deformation temperatures, strain rates and deformation degrees. The kinetics of static and metadynamic recrystallization are established and the results show that, the static recrystallization fraction is increasing with the increase of deformation temperature, strain rate and deformation degree; the metadynamic recrystallization fraction has the monotone increasing relationship with deformation temperature, strain rate and deformation degree. The softening methods of the deformed as-cast P91 alloy can be divided into three conditions through the values of true strain: whenε<εc, the static recrystallization operates as the prime softening mechanism in the inter-pass time; whenεc<ε<εT, both static and metadynamic recrystallization are involved in the softening; whenε>εT, the metadynamic recrystallization is the predominante softening mechanism. In addition, the microstructure of the specimens are observed, it can be found that the grain sizes of MDRX are smaller than SRX in the same deformation conditions, the grain sizes of recrystallization are increasing with the increase of deformation temperature and decrease with the increase of strain rate.

Key words: heavy caliber thick-wall pipe, hot deformation, metadynamic recrystallization, static recrystallization, true strain, heat resistance alloy steel