Co-Cu-Pb三元合金的快速凝固组织及电学性能研究

doi:10.3901/JME.2017.18.099

机械工程学报 ›› 2017, Vol. 53 ›› Issue (18): 99-105.doi: 10.3901/JME.2017.18.099

扫码分享

Co-Cu-Pb三元合金的快速凝固组织及电学性能研究

高卡¹, 郭晓琴¹, 张锐^1,2

1. 郑州航空工业管理学院河南省航空材料与应用技术重点实验室郑州 450015;
2. 郑州大学材料科学与工程学院郑州 450001

收稿日期:2016-06-05 修回日期:2017-01-18 出版日期:2017-09-20 发布日期:2017-09-20
通讯作者: 高卡(通信作者),男,1985年出生,博士研究生.主要研究方向为凝固理论及特种加工技术.E-mail:gaoka9222005@163.com E-mail:gaoka9222005@163.com
基金资助:
河南省科技攻关（162102210241）和河南省高等学校重点科研（17A430007）资助项目。

Study on Rapid Solidification Microstructure and Electrical Property of Co-Cu-Pb Ternary Alloy

GAO Ka¹, GUO Xiaoqin¹, ZHANG Rui^1,2

1. Henan Key Laboratory of Aeronautical Material and Application Technology, Zhengzhou University of Aeronautics, Zhengzhou 450015;
2. School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001

Received:2016-06-05 Revised:2017-01-18 Online:2017-09-20 Published:2017-09-20

摘要/Abstract

摘要： 采用单辊快速凝固技术研究Co-Cu-Pb三元难混溶合金薄带的快速凝固组织特征及电学性能，并通过将金属熔体热传导方程与Navier-Stokes方程相耦合，理论计算合金薄带的冷却速率。结果表明：在急冷快速凝固条件下，Co-Cu-Pb三元难混溶合金薄带的凝固组织由优先生长的Co（Cu）相枝晶骨架和枝晶间的富Pb相组成。随着冷却速率的增大，Co（Cu）相枝晶尺寸明显减小，凝固组织均匀性得到改善；而随着Pb含量的增大，少量的Pb相析出存在于Co（Cu）相枝晶干上。冷却速率的增大，合金薄带组织均匀性引起电子散射源减少，导致自由电子的散射作用减弱，使得合金薄带的电阻率减少。而合金中Pb含量的增大，减少了导电的有效电荷数，使得合金薄带的电阻率增大。快速凝固技术有效地改善了Co-Cu-Pb难混溶合金薄带的凝固组织均匀性和电学性能。

关键词: Co-Cu-Pb难混溶合金, 电学特性, 金属材料, 快速凝固, 微观组织

Abstract: The rapid solidification microstructure characteristic and electrical property of Co-Cu-Pb ternary immiscible alloy ribbon are investigated by using the rapid solidification with a single roller experimental apparatus. Through coupled the melt heat conduct equation and Navier-Stokes equation, the cooling rates are calculated theoretically. The results show that:Under rapid solidification conditions, the microstructure of alloys ribbons are consists of Co(Cu) phase dendrite and Pb-rich phase mainly distributed in dendrite boundary. With the rise of cooling rate, the size of Co(Cu) phase dendrite is decreased and its microstructure is remarkably refined. A small quantity of fine Pb phase precipitates inside dendrite branch with the rise of Pb content. The uniformity of the solidified microstructure is improved. With the increase of cooling rate, the electron scattering sources are decreased and the free electron scattering effect is weakened, which resulting in the decreasing of alloy electrical resistivity. And with Pb content increasing, the number of conductive effective charge is reduced, resulting in the increasing of alloy electrical resistivity. Rapid solidification could effectively improve the solidified microstructure uniformity and electrical properties of Co-Cu-Pb alloy ribbon.

Key words: Co-Cu-Pb immiscible alloy, electrical property, metallic materials, microstructure, rapid solidification

中图分类号:

TG111

高卡, 郭晓琴, 张锐. Co-Cu-Pb三元合金的快速凝固组织及电学性能研究[J]. 机械工程学报, 2017, 53(18): 99-105.

GAO Ka, GUO Xiaoqin, ZHANG Rui. Study on Rapid Solidification Microstructure and Electrical Property of Co-Cu-Pb Ternary Alloy[J]. Journal of Mechanical Engineering, 2017, 53(18): 99-105.

参考文献

[1] LU W Q, ZHANG S G, HU Q D, et al. Interaction between L2 droplets and L1/L interface in solidifying Al-Bi immiscible alloy[J]. Materials Letters, 2016, 182:351-354.
[2] XIE H, SUN J, YANG G C, et al. Liquid phase separation and its thermodynamic description in undercooled Ni-Pb hypermonotectic melts[J]. Materials Science and Engineering A, 2007, 457:33-37.
[3] WANG H P, WEI B B. Understanding atomic-scale phase separation of liquid Fe-Cu alloy[J]. Chinese Science Bulletin, 2011, 56(32):3416-3419.
[4] 李微, 梁慧, 陈荐, 等. 多孔Cu-Ni-Al合金的高温压缩变形行为及本构关系[J]. 机械工程学报, 2015, 51(2):58-64. LI Wei, LIANG Hui, CHEN Jian, et al. High temperature deformation behaviors and constructive relation of the porous Cu-Ni-Al sintered alloys[J]. Journal of Mechanical Engineering, 2015, 51(2):58-64.
[5] ZHAI W, LIU H M, WEI B. Liquid phase separation and monotectic structure evolution of ternary Al62.6Sn28.5Cu8.9 immiscible alloy within ultrasonic field[J]. Materials Letters, 2015, 141:221-224.
[6] 李亮, 白朴存, 侯小虎, 等. Al-Zn-Mg-Cu合金残余应力的会聚束电子衍射研究[J]. 机械工程学报, 2013, 49(2):54-58. LI Liang, BAI Pucun, HOU Xiaohu, et al. Measurement of residual strain tensor of Al-Zn-Mg-Cu alloy precipitated phase interface and interface vicinity on the matrixes using convergent-beam electron diffraction[J]. Journal of Mechanical Engineering, 2013, 49(2):54-58.
[7] WANG S, SONG L, KANG S, et al. Deformation behavior and microstructure evolution of wrought magnesium alloys[J]. Chinese Journal of Mechanical Engineering, 2013, 26(3):437-447.
[8] 张宏闻, 冼爱平. 第三组元对Al-Bi偏晶合金凝固组织的影响[J]. 金属学报, 2000, 36(4):347-350. ZHANG Hongwen, XIAN Aiping. Effect of the third element on the structure of casting Al-Bi immiscible alloys[J]. Acta Metallurgica Sinca, 2000, 36(4):347-350.
[9] AKIHIKO K, HIROYASU T, SHINJI K. Solidification structure of monotectic alloys[J]. Materials Science and Engineering A, 1991, 146(1):105-121.
[10] CHEN Y Z, LIU F, YANG G C, et al. Rapid solidification of bulk undercooled hypoperitectic Fe-Cu alloy[J]. Journal of Alloys and Compounds, 2007, 427:1-5.
[11] 闫娜, 王伟丽, 代富平, 等. 三元Co-Cu-Pb偏晶合金的快速凝固组织形成规律研究[J]. 物理学报, 2011, 60(3):465-473. YAN Na, WANG Weili, DAI Fuping, et al. Microstructure formation mechanism of rapidly solidified ternary Co-Cu-Pb monotectic alloys[J]. Acta Physica Sinca, 2011, 60(3):465-473.
[12] 徐锦锋, 魏炳波. 急冷快速凝固过程中液相流动与组织形成的相关规律[J]. 物理学报, 2004, 53(6):1909-1915. XU Jinfeng, WEI Bingbo. Liquid phase flow and microstructure formation during rapid solidification[J]. Acta Physica Sinica, 2004, 53(6):1909-1915.
[13] 惠希东, 杨院生, 陈晓明, 等. 单辊法制备非晶合金中的传热与熔体流动数值模拟[J]. 金属学报, 1999, 35(11):1206-1210. HUI Xidong, YANG Yuansheng, CHEN Xiaoming, et al. Numerical simulation of heat transfer and fluid flow during preparing amorphous alloy by single-roller spinning[J]. Acta Metallurgica Sinca, 1999, 35(11):1206-1210.
[14] SMITHELLS C J. Metals reference book[M]. London:Butterworths, 1984.
[15] GUO F, LU T, QIN J, et al. Abnormal resistivity behavior of Cu-Ni and Cu-Co alloys in undercooled liquid state[J]. Physica B Condensed Matter, 2012, 407(21):4108-4113.
[16] MUNITZ A, BAMBERGER M, WNNAPATHUN S, et al. Effects of supercooling and cooling rate on the microstructure of Cu-Co-Fe alloys[J]. Journal of Materials Science, 2006, 41(10):2749-2759.
[17] YAN N, WANG W L, WEI B. Complex phase separation of ternary Co-Cu-Pb alloy under containerless processing condition[J]. Journal of Alloys and Compounds, 2013, 558(5):109-116.
[18] ZHANG Y, GAO J, YASUDA H, et al. Particle size distribution and composition in phase-separated Cu75Co25 alloys under various magnetic fields[J]. Scripta Materialia, 2014, 82(7):5-8.
[19] YAN N, WANG W L, XIA Z C, et al. Solute redistribution profiles during rapid solidification of undercooled ternary Co-Cu-Pb alloy[J]. Science China Physics, Mechanics and Astronomy, 2014, 57(3):393-399.
[20] 翟秋亚, 杨扬, 徐锦锋. 快速凝固Cu-Sn亚包晶合金的电阻率及力学性能[J]. 物理学报, 2007, 56(10):6118-6123. ZHAI Qiuya, YANG Yang, XU Jinfeng. Electrical resistivity and mechanical properties of rapidly solidify Cu-Sn hypoperitectic alloys[J]. Acta Physica Sinica, 2007, 56(10):6118-6123.
[21] PATTANAIK G R, KASHYAP S C, PANDYA D K. Structure and giant magnetoresistance in electrodeposited granular Cu-Co films[J]. Journal of Magnetism and Magnetic Materials, 2000, 219:309-316.

Co-Cu-Pb三元合金的快速凝固组织及电学性能研究

Study on Rapid Solidification Microstructure and Electrical Property of Co-Cu-Pb Ternary Alloy

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	李坤, 吉辰, 白生文, 蒋斌, 潘复生. 高性能镁合金电弧增材制造技术研究现状与展望[J]. 机械工程学报, 2024, 60(7): 289-311.
[2]	陈伟, 赵杰, 朱利斌, 曹海波. 增材制造低活化钢研究现状及展望[J]. 机械工程学报, 2024, 60(7): 312-333.
[3]	郑洋, 赵梓昊, 刘伟, 余政哲, 牛伟, 雷贻文, 孙荣禄. 高性能镁合金增材制造技术研究进展[J]. 机械工程学报, 2024, 60(7): 385-400.
[4]	崔桂涵, 杨春利. 基于高强高韧焊丝的脉冲GMAW焊缝金属强韧化机理研究[J]. 机械工程学报, 2024, 60(4): 326-334.
[5]	马艺星, 杨蔚涛, 关肖虎, 杨旗, 赵同新. TWIP钢/IF钢热轧复合板材的微观结构和界面结合性能[J]. 机械工程学报, 2024, 60(4): 345-356.
[6]	冒爱琴, 陈诗洁, 贾洋刚, 邵霞, 权峰, 张晖, 张义伟, 金莹, 金霞. Al含量对粉末冶金CoCrFeMnNi高熵合金组织结构与性能的影响[J]. 机械工程学报, 2024, 60(20): 134-143.
[7]	褚强, 杨夏炜, 李文亚, 范文龙, 邹阳帆, 郝思洁. 铝锂合金无针搅拌摩擦点焊接头组织演变与强化机制研究[J]. 机械工程学报, 2024, 60(2): 150-158.
[8]	高恺, 顾红历, 李坤. Cr、Si微量元素对钢/铝感应静压焊接接头组织及性能的影响[J]. 机械工程学报, 2024, 60(2): 178-187.
[9]	张家豪, 王磊磊, 张彦霄, 黎一帆, 王晓明, 占小红. 激光熔化沉积TiC/TC4功能梯度材料微观组织与拉伸性能研究[J]. 机械工程学报, 2024, 60(19): 356-366.
[10]	谢云飞, 葛世鹏, 郭震国, 褚强, 张勇, 李文亚. 多层铝箔回填式搅拌摩擦点焊接头显微组织特征[J]. 机械工程学报, 2024, 60(18): 128-137.
[11]	王瑞林, 杨新岐, 唐文珅, 罗庭. AA2024-T3铝合金搅拌摩擦沉积增材组织及性能[J]. 机械工程学报, 2024, 60(18): 146-153.
[12]	王高见, 刘丽, 康丹丹, 叶延洪, 邓德安. Ni含量对高速列车转向架耐候钢焊缝金属微观组织、力学性能及腐蚀行为的影响[J]. 机械工程学报, 2024, 60(18): 163-172.
[13]	闫玉升, 钟史放, 徐连勇, 赵雷, 韩永典. 焊接热输入对X65管道粗晶热影响区应力腐蚀开裂行为的影响[J]. 机械工程学报, 2024, 60(12): 220-227.
[14]	高转妮, 王磊磊, 李响, 刘志强, 吕飞阅, 黎一帆, 占小红. 7075铝合金激光熔丝增材制造热循环和温度梯度对熔池凝固组织的影响研究[J]. 机械工程学报, 2024, 60(1): 96-118.
[15]	毛聪, 孙鹏程, 唐伟东, 张明军, 罗源嫱, 胡永乐, 张德嘉, 唐昆, 管付如. 磨削白层特性及其与声发射信号的相关性[J]. 机械工程学报, 2023, 59(9): 349-359.