Evaluation Method of Usability of the Flux-cored Wire in CO2 Arc Welding

Abstract

Abstract: Metal transfer behaviors of the flux-cored wire in CO2 arc welding have a direct effect on usability of the flux-cored wire. These behaviors are indirectly showed in welding electric signals. Using the ANALYSATOR HANNOVER, welding electric parameters of the flux-cored wires in CO2 arc welding are measured and analyzed. Four characteristic information values closely correlated with usability of the flux-cored wire are extracted, such as the sum of probability density of big short-circuiting current, frequency of short-circuiting transfer, frequency of brief short circuit and the sum of brief short-circuiting time, and then method of principal component analysis is applied to determining evaluation index of usability of the flux-cored wire. Usability of the flux-cored wire is quantitatively evaluated. Thereby it offers a new method for scientifically evaluating usability of the flux-cored wire.

Key words: Evaluation method, Flux-cored wire, Metal transfer, Principal component analysis, Usability of the flux-cored wire

CLC Number:

TG42

WANG Yong;WANG Bao. Evaluation Method of Usability of the Flux-cored Wire in CO2 Arc Welding[J]. , 2008, 44(4): 234-238.

[1]	DUAN Shuyong, YANG Jianhua, HAN Xu, LIU Guirong. Adaptive Dimensionality Reduction Method for High-dimensional Data [J]. Journal of Mechanical Engineering, 2024, 60(17): 283-296.
[2]	Yumin Peng, Ying Yang, Man Chen, Xuelin Wang, Yijun Xiong, Mu Wang, Yikai Li, Bushi Zhao. Value Evaluation Method for Pumped Storage in the New Power System^* [J]. Chinese Journal of Electrical Engineering, 2023, 9(3): 26-38.
[3]	LIU Yan, LIU Ao, ZHANG Linlin, DU Anna, LIU Zhaozhen, HE Chunlin. Study on the Porosity and Zinc Coating of CMT Welded Joints of DP590 Galvanized Dual-phase Steel [J]. Journal of Mechanical Engineering, 2023, 59(16): 213-222.
[4]	ZHAO Yong, GUO Jiang, FENG Jian, WANG Qinqiang, LONG Pengyu, ZHANG Jinlong, ZHANG Linwei, WANG Shuo, MENG Linggang, JIN Zhuji, KANG Renke. Recent Progress of Cleaning Technologies and Cleanliness Evaluation Methods for Metal Substrates [J]. Journal of Mechanical Engineering, 2023, 59(13): 290-313.
[5]	WANG Weiwei, WEI Ting, YU Suihuai, CHEN Jian. Research on the Evaluation Method of Interactive Cognitive Load of Intelligent Products for Dynamic Scenarios [J]. Journal of Mechanical Engineering, 2023, 59(11): 106-116.
[6]	ZHANG Xiaoying, WU Hongqiang, SHU Zijiang, WANG Kun, CHEN Wei. Equivalent Modeling of DFIG Wind Farm Based on PCA and Improved ABC-K Clustering Algorithm [J]. Journal of Electrical Engineering, 2023, 18(1): 201-210.
[7]	LI Jianwei, HE Zhi, LONG Jianzhou, YIN Fengliang, GAO Hongyue, ZHAO Yue, GUO Xiaolin, WANG Zhimin, LIU Yuping, ZHANG Tiejun, GUO Bin. Control of Defects in Mg Alloy Arc Additive Repair Layer by Friction Stir Treatment [J]. Journal of Mechanical Engineering, 2022, 58(4): 55-61.
[8]	ZHANG Kai, FENG Guang, XU Mingming, GE Guowei. Analysis on Key Factors of Primary and Secondary Integration of Distribution Switch Based on AHP-fuzzy Comprehensive Evaluation [J]. Journal of Electrical Engineering, 2022, 17(2): 187-193.
[9]	ZHAO Wenyong, CAO Xiyong, DU Xinwei, WEI Yanhong, LIU Renpei, CHEN Jicheng. Numerical Simulation of Heat and Mass Transfer in CMT-based Additive Manufacturing [J]. Journal of Mechanical Engineering, 2022, 58(1): 267-276.
[10]	Lü Yang, QIAN Bin, HU Rong, ZHANG Ziqi. Co-evolution Cross-entropy Optimization Algorithm for Cast Uncertain Steelmaking-continuous Casting Scheduling [J]. Journal of Mechanical Engineering, 2021, 57(19): 192-207.
[11]	HU Hongwei, ZHOU Gang, SHEN Xiaowei, XU Xiaoqiang. PCA-WHMM-based Frequency-domain Synthetic Aperture Focusing Imaging Using Ultrasonic Leaky Rayleigh Waves [J]. Journal of Mechanical Engineering, 2021, 57(14): 177-187.
[12]	LI Yanbiao, WANG Zesheng, SUN Peng, XU Taotao, QIN Songyang. Dynamic Load Distribution Optimization for a 4-DOF Redundant and Series-parallel Hybrid Humanoid Arm [J]. Journal of Mechanical Engineering, 2020, 56(9): 45-54.
[13]	CHANG Jinghuan, CAO Rui, LIN Qiaoli. Wetting and Interface Microstructures of Copper Alloy on Titanium and Steel Surfaces under Cold Metal Transfer Condition [J]. Journal of Mechanical Engineering, 2020, 56(6): 110-117.
[14]	WANG Qingfeng, WEI Bingkun, LIU Jiahe, MA Wensheng, XU Shujian. Research on Construction and Application of Data-driven Incipient Fault Detection Model for Rotating Machinery [J]. Journal of Mechanical Engineering, 2020, 56(16): 22-32.
[15]	FANG Xuewei, BAI Hao, YAO Yunfei, ZHANG Lijuan, LU Bingheng. Research on Multi-bead Overlapping Process of Wire and Arc Additive Manufacturing Based on Cold Metal Transfer [J]. Journal of Mechanical Engineering, 2020, 56(1): 141-147.

Evaluation Method of Usability of the Flux-cored Wire in CO2 Arc Welding

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments