Research on Fuel Economy Control of Hydrostatic Propulsion Vehicles Considering Efficiency

doi:10.3901/JME.260123

Abstract

Abstract: To achieve optimal fuel economy for hydrostatic propulsion vehicles, a fuel economy control strategy considering pump and motor efficiency is proposed. Firstly, the role of system fuel consumption in relation to engine efficiency and hydrostatic drive system efficiency is analyzed. On the basis of the efficiency analysis, the optimal speed ratio for the joint efficient operation of the engine and hydrostatic propulsion system at various throttle openings and vehicle speeds is obtained with the goal of minimizing fuel consumption. A simulation model is established to compare the control strategies before and after optimization. The results indicate that the fuel consumption is reduced by 8.74% under cyclic operating conditions. To address the difficulty in obtaining practical system efficiency, an efficiency correction factor is proposed to modify the theoretical control strategy. A test vehicle is constructed, the model accuracy and the validity of proposed method are verified by vehicles. The results of a 40 km/h constant speed driving test demonstrate that the 100-kilometre fuel consumption is reducible by the proposed control strategy, achieving good fuel economy for hydrostatic propulsion vehicles.

Key words: hydrostatic propulsion, continuously variable transmission, fuel economy, pump motor control, efficiency

CLC Number:

TH137

LIU Qihui, SUN Xiaopeng, MA Xiaohan, WU Wei. Research on Fuel Economy Control of Hydrostatic Propulsion Vehicles Considering Efficiency[J]. Journal of Mechanical Engineering, 2026, 62(4): 263-270.

Add to citation manager EndNote|Reference Manager|ProCite|BibTeX|RefWorks

URL: http://www.cjmenet.com.cn/EN/10.3901/JME.260123

http://www.cjmenet.com.cn/EN/Y2026/V62/I4/263

References

[1] XIA Y，SUN D. Characteristic analysis on a new hydro-mechanical continuously variable transmission system[J]. Mechanism and Machine Theory，2018，126：457-467.
[2] JANARTHANAN B，PADMANABHAN C，SUJATHA C. Longitudinal dynamics of a tracked vehicle：Simulation and experiment[J]. Journal of Terramechanics，2012，49(2)：63-72.
[3] DASGUPTA K. Analysis of a hydrostatic transmission system using low speed high torque motor[J]. Mechanism & Machine Theory，2000，10(35)：1481-1499.
[4] LI Y，HE L. Counterbalancing speed control for hydrostatic drive heavy vehicle under long down-slope[J]. IEEE/ASME Transactions on Mechatronics，2015，20(4)：1533-1542.
[5] 朱镇，蔡英凤，陈龙，等. 基于遗传算法的机液传动系统参数匹配研究[J]. 汽车工程，2020，42(1)：74-80. ZHU Zhen，CAI Yingfeng，CHEN Long，et al. A study on parameter matching of hydro-mechanical transmission system based on genetic algorithm[J]. Automotive Engineering，2020，42(1)：74-80.
[6] 张明柱，王界中，王建华，等. 提高燃油经济性的拖拉机变速控制策略[J]. 农业工程学报，2020，36(1)：82-89. ZHANG Mingzhu，WANG Jiezhong，WANG Jianhua，et al. Speed changing control strategy for improving tractor fuel economy[J]. Transactions of the Chinese Society of Agricultural Engineering，2020，36(1)：82-89.
[7] 罗勇，孙冬野，秦大同，等. 考虑CVT效率的无级变速车辆最佳经济性控制[J]. 机械工程学报，2010，46(4)：80-86. LUO Yong，SUN Dongye，QIN Datong，et al. Fuel optimal control of CVT equipped vehicles with consideration of CVT efficiency[J]. Journal of Mechanical Engineering，2010，46(4)：80-86.
[8] 黄薛凯，鲁植雄，陈雷，等. 基于整机经济性的拖拉机HMCVT目标速比优化及控制仿真[J]. 南京农业大学学报，2022，45(4)：777-787. HUANG Xuekai，LU Zhixiong，CHEN Lei，et al. Optimization of tractor HMCVT target speed ratio and control simulation based on machine economy[J]．Journal of Nanjing Agricultural University，2022，45(4)：777-787.
[9] 梁丽，李青涛，谭芸颖，等. 基于参数循环算法的HMCVT燃油经济性多参数优化[J]. 农业工程学报，2023，39(10)：48-55. LIANG Li，LI Qingtao，TAN Yunying，et al. Multi-parameter optimization of HMCVT fuel economy using parameter cyclic algorithm[J]. Transactions of the Chinese Society of Agricultural Engineering，2023，39(10)：48-55.
[10] 卞永明，宁晓贤，赵芳伟，等. DA-HA闭式控制系统在工程机械中的应用[J]. 中国工程机械学报，2012，10(1)：58-63. BIAN Yongming，NING Xiaoxian，ZHAO Fangwei，et al. Applying DA-HA close-loop control system for construction machinery[J]. Chinese Journal of Construction Machinery，2012，10(1)：58-63.
[11] RUBIEC A，PRZYBYSZ M，LOPATKA M，et al. Influence of flow divider on overall efficiency of a hydrostatic drivetrain of a skid-steer all-wheel drive multiple-axle vehicle[J]. Energies，2021，14(12)：3560.
[12] WANG X，WANG Z，XIE L，et al. Research on the new hydrostatic transmission system of wheel loaders based on fuzzy sliding mode control[J]. Energies，2024，17(3)：565.
[13] 罗俊林，吴维，邹天刚，等. 静液压驱动车辆加速过程动态特性研究[J]. 机械工程学报，2023，59(16)：254-262. LUO Junlin，WU Wei，ZOU Tiangang，et al. Study on dynamic characteristics of hydrostatic driven vehicle acceleration process[J]. Journal of Mechanical Engineering，2023，59(16)：254-262.
[14] PAOLUZZI R，ZAROTTI L. The minimum size of hydrostatic transmissions for locomotion[J]. Journal of Terramechanics，2013，50(3)：153-164.

[1]	HUANG Xiaomin, GUO Tong, QUE Fumin, LI Xinming, LIU Hao, LIN Tianliang. Novel Configuration of High-pressure Radial Piston Motor with Plate Pilot Pressure Control for Two-stage Flow Distribution and Its Volumetric Efficiency Characteristics [J]. Journal of Mechanical Engineering, 2026, 62(6): 409-418.
[2]	LI Xiaohua, LI Xu, HAN Yuejiao, WANG Pengfei, ZHANG Dianhua, ZHANG Yong. Prediction and Regulation of Multi-pass Coupled Modeling for Cold Rolling of High-strength Strip Based on Genetic Inheritance of Property Inhomogeneity [J]. Journal of Mechanical Engineering, 2026, 62(4): 135-147.
[3]	WANG Wei, WANG Junlong, LUO Xingqi, CU Tingting, LU Jinling, FENG Jianjun. Study on Optimization of Non-symmetric Volute and Underlying Mechanism for Centrifugal Fan [J]. Journal of Mechanical Engineering, 2026, 62(4): 400-412.
[4]	DU Xinwei, WEI Yanhong, SHEN Yonghua, ZHAO Wenyong, LIU Renpei. Development Status of Wire Arc Additive Manufacturing Equipment System and Application [J]. Journal of Mechanical Engineering, 2025, 61(6): 92-102.
[5]	JIANG Shengda, HE Ji, GUO Cong, LI Shuhui, QIAN Changming. Data-driven Self-consistent Clustering Analysis and High-efficiency Cross-scale Simulation of Plastic Forming Process [J]. Journal of Mechanical Engineering, 2025, 61(4): 74-85.
[6]	LI Lei, HU Guozeng, XUAN Dengshi, HUANG Haihong. Short-time Pulse Based Electromagnetic Variable Blank Holding for High Efficiency Forming and Analysis of Energy Characteristics [J]. Journal of Mechanical Engineering, 2025, 61(23): 203-216.
[7]	BA Jinlei, JIANG Zhiwen, WU Defa, CUI Yan, LIU Yinshui. Simulation and Experimental Analysis of Flow Distribution Performance of the Micro Piston Pump [J]. Journal of Mechanical Engineering, 2025, 61(22): 370-382.
[8]	HOU Shengwen, ZHOU Changjiang, XIA Ningwei, DONG Fan. Transmission Efficiency Model and Experiment of High-speed Reducer [J]. Journal of Mechanical Engineering, 2025, 61(19): 54-62.
[9]	HUANG Weidi, GUO Yitao, WANG Feng, ZONG Huaizhi, ZHANG Junhui, NI Xiaohao, XU Bing. Design and Energy Efficiency Research of an Integrated Electro-hydraulic Actuator for Excavator Boom [J]. Journal of Mechanical Engineering, 2025, 61(18): 396-405.
[10]	XIE Junhua, XU Zhijia. Efficient Intelligent Assembly Modeling Method Based on the Cognition of Interaction Structures [J]. Journal of Mechanical Engineering, 2025, 61(12): 327-335,343.
[11]	WEN Qiuling, YANG Ye, HUANG Hui, HUANG Guoqin, HU Zhongwei, CHEN Jinhong, WANG Hui, WU Xian. Review of Research Progress in Laser-based Hybrid Machining of Hard and Brittle Materials [J]. Journal of Mechanical Engineering, 2024, 60(9): 168-188.
[12]	ZHAO Xikun, LI Congbo, YANG Yong, Lü Yan, JIANG Shuyan. A Data and Model Hybrid Driven Cutting Parameter Energy-efficiency Optimization Method for Flexible Machining Process Considering Cutting Tool Flexibility [J]. Journal of Mechanical Engineering, 2024, 60(7): 236-248.
[13]	DING Wenfeng, ZHAO Junshuai, ZHANG Honggang, ZHAO Biao, SI Wenyuan, SONG Qiang, HUANG Qingfei. Advances in High Efficiency Precision Grinding and Surface Integrity Control Technology for Gears [J]. Journal of Mechanical Engineering, 2024, 60(7): 350-373.
[14]	YUAN Song, GUO Xiaoguang, JIN Zhuji, KANG Renke, GUO Dongming. A Review of High-efficiency and Ultra-low Damage Processing Mechanism and Technology of Diamond [J]. Journal of Mechanical Engineering, 2024, 60(3): 337-353.
[15]	DUAN Rong, JIANG Zhigang, ZHANG Hua, GONG Qingshan, LI Mingyao. The Difficulties and Challenges of Energy Efficiency Maintenance for Electromechanical Equipment over the Whole Operating Range [J]. Journal of Mechanical Engineering, 2024, 60(23): 354-364.