Material Removal Mechanism and Evaluation of Machined Surface Quality of SiCf/SiC Composites by Laser Ablation-assisted Milling

doi:10.3901/JME.2024.09.206

Abstract

Abstract: The high temperature resistance, high strength and light weight of SiC_f/SiC composites are required for modern aerospace components, and SiC_f/SiC composites have excellent comprehensive performance, but their high brittleness and anisotropy make it a challenge for high-performance manufacturing. Through the laser ablation pre-test, the physical phase composition and ablation mechanism of laser ablation products of SiCf/SiC composites are grasped, and the influence of laser parameters on the ablation properties is investigated. Through the comparison experiments of conventional milling and laser ablation-assisted milling, the material removal mechanisms of three different processing strategies, namely, conventional milling, partial ablation-milling and complete ablation-milling, are analysed, and the influence of the ablation layer ratio on the processing surface quality is investigated. It is shown that the laser ablation products are mainly composed of 3C-SiC and amorphous SiO₂. In conventional milling, macroscopic brittle fracture of fibres occurred, and machining defects such as multiple cracks and pits existed on the machined surface. In partial ablation-milling, fibre fracture is dominated by microscopic brittle fracture, and fibre pull-out and macroscopic brittle fracture occurred at a few locations. In the full ablation-milling process, microscopic brittle fracture of fibres occurred, and scale fracture of the matrix occurred. The quality of laser ablation-assisted milling machining is superior to conventional milling, and the surface roughness was essentially the same for partial ablation-milling and complete ablation-milling. The difference in cutting force between milling with low and high ablative layer percentage is small. Micro-macro brittle fracture dominated the fibres in the milling process with low ablative layer percentage; micro-brittle fracture occurred in most of the fibres in the milling process with high ablative layer percentage. In summary, partial ablation-milling and low ablative layer ratio are the preferred processing solutions.

Key words: SiC_f/SiC composite, laser-assisted milling, material removal mechanism, machining quality

CLC Number:

TH16

LI Han, ZHANG Cheng, CHEN Jie, AN Qinglong, CHEN Ming. Material Removal Mechanism and Evaluation of Machined Surface Quality of SiCf/SiC Composites by Laser Ablation-assisted Milling[J]. Journal of Mechanical Engineering, 2024, 60(9): 206-217.

Add to citation manager EndNote|Reference Manager|ProCite|BibTeX|RefWorks

URL: http://www.cjmenet.com.cn/EN/10.3901/JME.2024.09.206

http://www.cjmenet.com.cn/EN/Y2024/V60/I9/206

References

[1] SHIMODA K，KAKISAWA H. Novel production route for SiC/SiC ceramic-matrix composites using sandwich prepreg sheets[J]. Journal of the European Ceramic Society，2023，43(3)：805-813.
[2] DIAZ O，LUNA G，LIAO Z，et al. The new challenges of machining ceramic matrix composites (CMCs)：Review of surface integrity[J]. International Journal of Machine Tools and Manufacture，2019，139：24-36.
[3] AN Q，CHEN J，MING W，et al. Machining of SiC ceramic matrix composites：A review [J]. Chinese Journal of Aeronautics，2021，34(4)：540-567.
[4] XIONG Y，LIU C，WANG W，et al. Assessment of machined surface for SiC_f/SiC ceramic matrix composite during ultrasonic vibration-assisted milling-grinding[J]. Ceramics International，2023，49(3)：5345-5356.
[5] 董志刚，马槐遥，康仁科，等. SiCf/SiC复合材料超声辅助干式侧磨砂轮磨损研究[J]. 机械工程学报，2022，58(15)：134-143. DONG Zhigang，MA Huaiyao，KANG Renke，et al. Study on wear of grinding wheel in ultrasonic assisted dry side grinding of SiC_f/SiC composites[J]. Journal of Mechanical Engineering，2022，58(15)：134-143.
[6] CHEN J，AN Q，CHEN M. Transformation of fracture mechanism and damage behavior of ceramic-matrix composites during nano-scratching[J]. Composites Part A：Applied Science and Manufacturing，2020，130：105756.
[7] 田纪文. CMC-SiC激光辅助高速微切削温度场分析与试验研究[D]. 长春：长春理工大学，2021. TIAN Jiwen. Analysis and experimental study of temperature field of CMC-SiC laser-assisted high-speed micromachining[D]. Changchun：Changchun University of Science and Technology，2021.
[8] 杨佳，张勋业，马广璐，等. SiCf/SiC复合材料与镍基高温合金钎焊接头的组织及性能[J]. 机械工程学报，2021，57(12)：161-168. YANG Jia，ZHANG Xunye，MA Guanglu，et al. Microstructure and properties of brazed joint between SiC_f/SiC composite and Ni-based superalloy[J]. Journal of Mechanical Engineering，2021，57(12)：161-168.
[9] YUAN S，FAN H，MUHANMMAD A，et al. A cutting force prediction dynamic model for side milling of ceramic matrix composites C/SiC based on rotary ultrasonic machining[J]. The International Journal of Advanced Manufacturing Technology，2016，86：37-48.
[10] SADAGOPAN P，MOULIPRASANTH B. Investigation on the influence of different types of dielectrics in electrical discharge machining[J]. The International Journal of Advanced Manufacturing Technology，2017，92(1-4)：277-291.
[11] CHEN J，AN Q，MING W，et al. Investigations on continuous-wave laser and pulsed laser induced controllable ablation of SiCf/SiC composites [J]. Journal of the European Ceramic Society，2021，41(12)：5835-5849.
[12] CHEN J，AN Q，GONG Q，et al. Machinability improvement in milling of SiCf/SiC composites based on laser controllable ablation pretreatment[J]. Journal of the European Ceramic Society，2023，43(4)：1352-1365.
[13] TUERSLEY I，HOULT T，PASHBY I. The processing of SiC/SiC ceramic matrix composites using a pulsed Nd YAG laser Part I：Optimization of pulse parameters[J]. Journal of Materials Science，1998，33(4)：955-961.
[14] TUERSLEY I，HOULT T，PASHBY I. The processing of SiC/SiC ceramic matrix composites using a pulsed Nd-YAG laser Part II：The effect of process variables[J]. Journal of Materials Science，1998，33(4)：963-967.
[15] ZENG J，ZHANG Q，ZHAO J，et al. The formed surface characteristics of SiCf/SiC composite in the nanosecond pulsed laser ablation[J]. Ceramics International，2022，48(24)：36860-36870.
[16] LEE C，KIM D，BAEK J，et al. Laser assisted milling device：A review[J]. International Journal of Precision Engineering and Manufacturing-green Technology，2016，3(2)：199-208.
[17] MELKOTE S，KUMAR M，HASHIMOTO F，et al. Laser assisted micro-milling of hard-to-machine materials[J]. CIRP Annals-manufacturing Technology. 2009，58(1)：45-48.
[18] DONG X，SHIN Y. Improved machinability of SiC/SiC ceramic matrix composite via laser-assisted micromachining[J]. International Journal of Advanced Manufacturing Technology，2017，90(1-4)：731-739.
[19] 杨金华，黄望全，冯晓星，等. 激光类型对SiC/SiC复合材料孔加工的影响[J]. 航空材料学报，2023，43(1)：80-86. YANG Jinhua，HUANG Wangquan，FENG Xiaoxing，et al. Effect of laser type on hole machining of SiC/SiC composite[J]. Journal of Aerospace Materials，2023，43(1)：80-86.
[20] 赵国龙，夏宏军，李亮，等. 激光诱导可控氧化辅助微细铣削TiAl金属间化合物的研究[J]. 机械工程学报，2021，57(9)：254-263. ZHAO Guolong，XIA Hongjun，LI Liang，et al. Investigation on laser-induced controllable oxidation assisted micro milling of titanium aluminum intermetallic alloy[J]. Journal of Mechanical Engineering，2021，57(9)：254-263.
[21] LI H，ZHANG C，CHEN J，et al. Surface microstructure evolution of Cf/SiC ceramic matrix composite microgrooves processed by ultrafast laser[J]，Ceramics International，2023，49(18)：29477-29494.
[23] RAJ R，TERAUDS K. Bubble nucleation during oxidation of SiC[J]. Journal of the American Ceramic Society，2015，98(8)：2579-2586.
[24] GAO T，ZHANG Y，LI C，et al. Fiber reinforced composites in milling and grinding：Machining bottlenecks and advanced strategies[J]. Frontiers of Mechanical Engineering，2022，17(2)：24.
[25] 高腾，李长河，张彦彬，等. 纳米增强生物润滑剂CFRP材料去除力学行为与磨削力预测模型[J]. 机械工程学报，2023，59(13)：325-342. GAO Teng，LI Changhe，ZHANG Yanbin，et al. Mechanical behavior of material removal and predictive force model for CFRP grinding using nano reinforced biological lubricant[J]. Journal of Mechanical Engineering，2023，59(13)：325-342.
[26] ZHAO D，SUN S，ZHANG Y，et al. A study of laser machining combined with dynamic chemical etching in micro-hole drilling of 2.5D SiCf/SiC composites[J]. International Journal of Applied Ceramic Technology，2023，20：2522– 2535.