Influence of Stress Loading Path on the Limit of Plastic Wrinkling and Instability of Plates and Shells

doi:10.3901/JME.2021.04.083

Abstract

Abstract: With the increasing requirements for the lightness and toughness of metal products in the manufacturing technology fields such as aerospace, aviation, national defense and automobile, plastic instability has become one of the problems restricting the overall forming of metal products. Therefore, it is of great significance to predict and prevent the wrinkling and instability defects efficiently and accurately in the forming process of thin-walled components. Tensile test of wedge-shaped part is taken as the research object. By establishing numerical buckling model of wedge-shaped part and combining with bifurcation principle, a numerical solution and drawing method of WLD is proposed. In view of the significant influence of the stress loading path on the wrinkling instability of metal plate and shell specimens during the forming process, the stress loading path in different areas of the wedge is analyzed to explore the influence of the stress loading path on the critical wrinkling limit during plate and shell deformation. The results show that WLD should be built established in different regions for specimens with independent wrinkling regions under different stress states. The influence of stress loading path in different regions on WLD can be summarized as the influence of the critical wrinkling principal stress ratio on the principal strain ratio：when the critical wrinkling principal stress ratio is larger, the critical wrinkling principal strain ratio is larger, that is, the slope of WLD is larger, and the process resistance is weaker. At the same time, by comparing the load bearing histories of different wrinkling instability zones of the wedges, it can be seen that the increasing rate of critical principal compressive stress during wrinkling will affect the critical wrinkling instability moment of the sheet metal.

Key words: plate and shell forming, wrinkling limit diagram(WLD), wedge-shaped part, stress loading path, wrinkling instability numerical simulation

CLC Number:

TG386

DU Bing, ZHAO Chonghao, XIE Jun, LI Han, ZHAO Changcai, DU Zhiming. Influence of Stress Loading Path on the Limit of Plastic Wrinkling and Instability of Plates and Shells[J]. Journal of Mechanical Engineering, 2021, 57(4): 83-91.

References

[1] CHEN Y Z,LIU W,ZHANG Z C,et al. Analysis of wrinkling during sheet hydroforming of curved surface shell considering reverse bulging effect[J]. International Journal of Mechanical Sciences,2017,120:70-80.
[2] CAO J,CHENG S H,WANG H P,et al. Buckling of sheet metals in contact with tool surfaces[J]. CIRP Annals-Manufacturing Technology,2007,56(1):253-256.
[3] KOWSARINIA E,ALIZADEH Y,POUR H S S. Theoretical and experimental study on the effects of explosive forming parameters on plastic wrinkling of annular plates[J]. International Journal of Advanced Manufacturing Technology,2013,67(1-4):877-885.
[4] LI H,LIU H R,LIU N,et al. Towards sensitive prediction of wrinkling instability in sheet metal forming by introducing evolution of triple nonlinearity:Tube forming[J]. International Journal of Mechanical Sciences,2019,161:105054.
[5] ZHU H,HE Z,LIN Y,et al. The development of a novel forming limit diagram under nonlinear loading paths in tube hydroforming[J]. International Journal of Mechanical Sciences,2020,172:105392.
[6] GAJJAR N,MODI B,DIGAVALLI R K. Improvement in accuracy of failure prediction in sheet hydroforming of square cups using stress-based forming limit diagram[J]. Journal of Failure Analysis and Prevention,2019,19(6):1792-1800.
[7] 杨卓云,赵长财,董国疆,等. 基于Lou-2013韧性断裂准则5182铝板成形极限研究[J]. 机械工程学报,2019,55(16):47-57.YANG Zhuoyun,ZHAO Changcai,DONG Guojiang,et al. Research on forming limit of 5182 aluminum sheet based on Lou-2013 ductile fracture criterion[J]. Journal of Mechanical Engineering,2019,55(16):47-57.
[8] SZACINSKI A M,THOMSON P F. Investigation of the existence of a wrinkling-limit curve in plastically-deforming metal sheet[J]. Journal of Materials Processing Technology,1991,25(2):125-137.
[9] BAYRAKTAR E,ISAC N,Arnold G. Buckling limit diagrams (BLDs) of interstitial free steels (IFS):Comparison of experimental and finite element analysis[J]. Journal of Materials Processing Technology,2005,164:1487-1494.
[10] LIEWALD M,HAN F,RADONJIC R. New criterion for prediction of the wrinkle formation in deep drawing process[J]. Key Engineering Materials,2015,3974:71-76.
[11] 杜冰,关风龙,宋鹏飞,等. 薄板起皱失稳数值模拟计算方法[J]. 机械工程学报,2018,54(24):42-50.DU Bing,GUAN Fenglong,SONG Pengfei,et al. Numerical simulation calculation method for wrinkling and instability of thin plate[J]. Journal of Mechanical Engineering,2018,54(24):45-50.
[12] DU B,XIE J,LI H,et al. Determining factors affecting sheet metal plastic wrinkling in response to nonuniform tension using wrinkling limit diagrams[J]. Thin-Walled Structures,2020,147:106535.

[1]	HE Weilin, MENG Bao, WAN Min. Study on U-bending Springback Behavior of GH4169 Ultrathin Strip [J]. Journal of Mechanical Engineering, 2024, 60(14): 174-184.
[2]	DU Bing, TANG Sheng-qiang, HUANG Xiu-dong, LIU Feng-hua, CUI Hai-long. Research on the Mechanism of Multi-pass Ironing Drawing Process of High Box-shaped Parts and Establishment of Numerical Simulation Model [J]. Journal of Mechanical Engineering, 2022, 58(22): 235-249.
[3]	GUO Xiaoxi, LI Heng, FENG Zhenyong, ZHANG Duo. Macro-meso Scale Coupling Modeling and Simulation of Surface Roughening in Aluminum Alloy Tube Bending [J]. Journal of Mechanical Engineering, 2021, 57(22): 209-217.
[4]	GAO Song, SUN Yingli, LI Qihan, HE Tonggui, LIANG Jicai, XU Chuanwei. Precision Forming of the Asymmetric 3D Stretch-press Bending Parts for the Windows of the High Speed Trains [J]. Journal of Mechanical Engineering, 2021, 57(18): 222-228.
[5]	CAO Miaoyan, HU Han, TIAN Shaojie, DU Bing, ZHAO Changcai. FEM-DEM Coupling Analysis and Experimental Research on Soft Forming of Parabolic Shell [J]. Journal of Mechanical Engineering, 2020, 56(20): 38-46.
[6]	XIE Yanmin, YUE Yuepeng, FENG Meiqiang, GUO Yuanheng, WANG Dongtao, ZHU Yun. Design and Optimization of Pseudo Drawbeads in Nonisothermal Stamping of Magnesium Alloys Based on Level Set Theory and Kriging Model [J]. Journal of Mechanical Engineering, 2020, 56(12): 92-98.
[7]	BAO Yidong, QIAN Wenqing, CHEN Xiaoyu, CUN Wenyuan, SHU Yang. Fast Prediction Method of the Axial Contraction of Aviation Flared Tube [J]. Journal of Mechanical Engineering, 2020, 56(10): 102-109.
[8]	ZHAO Changcai, YUAN Rongjuan, HAO Haibin, HU Limei, JIA Xiangdong. Theoretical Calculation and Numerical Simulation on Roller Die Drawing Force of High Pressure Cylinder [J]. Journal of Mechanical Engineering, 2020, 56(4): 49-56.
[9]	DU Bing, SONG Pengfei, XIE Jun, ZHAO Changcai, GUAN Fenglong. Prediction of Critical Wrinkle Instability of Thin Plates by Combining Energy Method Theory with Numerical Simulation [J]. Journal of Mechanical Engineering, 2020, 56(4): 57-64.
[10]	GAO Song, YU Changchun, LIANG Jicai, LI Qihan, HAO Zhaopeng, LIU Xiaoyong, ZHAO Xilu. Multi-points 3D Stretch-press Bending Technology for Aluminum Profile [J]. Journal of Mechanical Engineering, 2019, 55(20): 152-159.
[11]	WEN Yue, CHEN Zhanghua. Failure Analysis of the Tube Hydroforming Process Based on Anisotropic Damage Coupling Model [J]. Journal of Mechanical Engineering, 2019, 55(18): 70-77.
[12]	XIE Yanmin, ZHANG Fei, PAN Beibei, FENG Meiqiang, YUE Yaopeng. Optimization of Drawbeads Based on Parallel Infilling Strategy and Kriging Models [J]. Journal of Mechanical Engineering, 2019, 55(8): 73-79.
[13]	BAI Lang, LI Yan, YANG Mingshun, YAO Zimeng, YAO Zhiyuan. Analytical Model of Ultrasonic Vibration Single Point Incremental Forming Force [J]. Journal of Mechanical Engineering, 2019, 55(2): 42-50.
[14]	DU Bing, GUAN Fenglong, SONG Pengfei, HAN Zhaojian, ZHANG Xin, ZHAO Changcai. Numerical Simulation Methods of Sheet Metal Wrinkling Instability Problem [J]. Journal of Mechanical Engineering, 2018, 54(24): 42-50.
[15]	ZHANG Yue, HE Xiaocong, LI Zhi, ZHANG Yihe. Fretting Fatigue Mechanism Research of the Aluminum Alloy Clinched Joints [J]. Journal of Mechanical Engineering, 2018, 54(19): 190-196.