Identification Method of Blade Vibration with High EO Based on Virtual Sensor Interpolation

doi:10.3901/JME.2019.19.001

Abstract

Abstract: The vibration of blades and the corresponding high-cycle fatigue fracture are the main problems in the development and operation of high-performance turbomachinery. High engine order (EO) vibration caused by the periodic pulsation of the flow parameters of high-load blades under the disturbance of wakes which is the main factors for high-cycle fatigue. Therefore, the high EO vibration monitoring is important for the diagnosis and early warning of high-cycle fatigue. A method is proposed for reconstruction and identification of high EO signals in rotating blades based on virtual sensor interpolation method, which can be a good solution for the vibration of blades with high EO, and can achieve vibrations up to 60EO when the angle of sensor installation is 6 degrees. Theoretically, only two sensors are needed for this method and four sensors can be used to ensure the identification accuracy in practical applications. What's more, only one start up or stop of the turbomachinery is needed to identify the vibration of blade, which simplifies the test steps. The method can be used for the vibration monitoring and identification of high-end rotating machinery such as aircraft engine, which has a large number of stationary blades and vibrates in high order mode and high-EO. The comparison between the experimental data and the simulation results indicates the effectiveness and accuracy of this method.

Key words: blade tip-timing (BTT), blade vibration, parameter identification, engine order (EO)

CLC Number:

TK14
V216

CHEN Kang, ZHANG Ya, WANG Weimin, ZHANG Xulong, HU Dongfang. Identification Method of Blade Vibration with High EO Based on Virtual Sensor Interpolation[J]. Journal of Mechanical Engineering, 2019, 55(19): 1-8.

References

[1] 张玉贵,段发阶,方志强,等. 基于叶尖定时的非接触式旋转叶片异步振动分析[J]. 机械工程学报,2008,44(7):147-150. ZHANG Yugui,DUAN Fajie,FANG Zhiqiang,et al. Analysis of non-contact asynchronous vibration of rotating blades based on tip-timing[J]. Chinese Journal of Mechanical Engineering,2008,44(7):147-150.
[2] 萨勃洛斯基. 涡轮机叶片振动的非接触测量[M]. 北京:国防工业出版社,1986. ЗАБЛОЦКИЙИЕ. The non-contact vibration measurement of turbine[M]. Beijing:National Defense Industry Press,1986.
[3] 欧阳涛,段发阶,闫明,等. 双参数法辨识叶片同步振动的研究[J]. 传感器与微系统,2010,29(3):42-45. OUYANG Tao,DUAN Fajie,YAN Ming,et al. Research on identifying synchronous blade vibration using two-parameter-plot method[J]. Transducer and Microsystem Technologies,2010,29(3):42-45.
[4] CARRINGTON,IAN B. Development of blade tip timing data analysis techniques[J]. Journal of Dental Education,2002,47(2):947-951.
[5] GALLEGOGARRIDO J,DIMITRIADIS G,WRIGHT J R. A class of methods for the analysis of blade tip timing data from bladed assemblies undergoing simultaneous resonances-Part I:Theoretical development[J]. International Journal of Rotating Machinery,2007(591):981-1077.
[6] 郭浩天,段发阶,汪猛. 基于叶尖定时单参数法的叶片共振倍频数辨识[J]. 天津大学学报,2016,49(9):951-955. GUO Haotian,DUAN Fajie,WANG Meng. Engine order identification based on blade tip-timing single parameter method[J]. Journal of Tianjin University,2016,49(9):951-955.
[7] 欧阳涛,郭文力,段发阶,等. 基于叶尖定时的旋转叶片同步振动辨识新方法[J]. 振动与冲击,2011,30(8):249-252. OUYANG Tao,GUO Wenli,DUAN Fajie,et al. A new method for identifying rotating blades synchronous vibration based on tip-timing[J]. Journal of Vibration and Shock,2011,30(8):249-252.
[8] 李孟麟,段发阶,欧阳涛,等. 基于叶尖定时的旋转机械叶片振动信号重建[J]. 机械工程学报,2011,47(13):98-103. LI Menglin,DUAN Fajie,OUYANG Tao,et a1.Reconstruction of the blade vibration signal from rotating machinery based on blade tip-timing measurement[J].Journal of Mechanical Engineering,2011,47(13):98-103.
[9] 王维民,任三群,陈立芳,等. 涡轮机叶片同步振动参数辨识方法研究(建模仿真)[J]. 振动与冲击,2017,36(17):120-126. WANG Weimin,REN Sanqun,CHEN Lifang,et a1. Investigation on the method of blade synchronous vibration parameter identification (simulation)[J]. Journal of Vibration and Shock,2017,36(17):120-126.
[10] 王维民,任三群,陈立芳,等. 涡轮机叶片同步振动参数辨识方法研究(实验研究)[J]. 振动与冲击,2017,36(17):127-133. WANG Weimin,REN Sanqun,CHEN Lifang,et al. Investigation on the method of blade synchronous vibration parameter identification (experimental)[J]. Journal of Vibration and Shock,2017,36(17):127-133.
[11] WANG W,REN S,HUANG S,et al. New step to improve the accuracy of blade synchronous vibration parameters identification based on combination of GARIV and LM algorithm[C]//ASME Turbo Expo 2017:Turbomachinery Technical Conference and Exposition. American Society of Mechanical Engineers,June 26-30,2017,Charlotte,North Carolina,USA,2017:V07BT35A017.
[12] 王维民,任三群,陈立芳,等. 基于键相插值法的叶片振动测量研究[J]. 振动、测试与诊断,2017,37(2):361-365. WANG Weimin,REN Sanqun,CHEN Lifang,et al. The blade vibration measurement research based on the key phase interpolation method (KPIM)[J]. Journal of Vibration,Measurement & Diagnosis,2017,37(2):361-365.
[13] 任三群. 基于数据融合的涡轮机叶片振动测量方法研究[D]. 北京:北京化工大学,2017. REN Sanqun. Investigation on method of turbine blade vibration measurement based on data fusion method[D]. Beijing:Beijing University of Chemical Technology,2017.
[14] 张娅,陈康,王维民,等. 叶片裂纹故障早期监测预警方法研究[J]. 风机技术,2017,59(4):45-50. ZHANG Ya,CHEN Kang,WANG Weimin,et al. Early monitoring and warning method for crack faults in blades[J]. Compressor,Blower & Fan Technology,2017,59(4):45-50.
[15] RIGOSI G,BATTIATO G,BERRUTI T M. Synchronous vibration parameters identification by tip timing measurements[J]. Mechanics Research Communications,2017,79:7-14.
[16] KHARYTON V,DIMITRIADIS G,DEFISE C,et al. A discussion on the advancement of blade tip timing data processing[C]//ASME Turbo Expo 2017:Turbomachinery Technical Conference and Exposition. American Society of Mechanical Engineers,June 26-30,2017,Charlotte,North Carolina,USA. 2017:V07BT35A002.