Special Processing Techniques Commonly Used For Silicon Carbide Ceramic-Based Composites: Review

doi:10.3901/JME.2023.01.199

Abstract

Abstract: Silicon carbide ceramic matrix composites (SiC-CMC) have many advantages, such as high hardness, high strength, high temperature resistance, corrosion resistance etc, showing great application potential in aerospace, nuclear industry, braking system. However, the characteristics of anisotropy, heterogeneity and hard brittleness of SiC-CMC make it very difficult to process. The traditional machining method has some problems such as difficult to control the surface quality, serious tool wear and low machining efficiency. In order to solve the above problems, special processing technology was tried to adopt machining SiC-CMC. However, there are many kinds of special processing technology, which involves more knowledge than traditional processing technology, wide and miscellany. In this paper, laser machining, abrasive water jet machining and electric discharge machining, which are of higher engineering practical value and stronger foundation, are selected to carry out a review. Firstly, the problems of three kinds of special processing technology are introduced and then the methods to solve the problems are summarized. Finally, the advantages and disadvantages of the three are compared and the conclusions are drawn:special processioning technology has its own advantages, laser machining is suitable for machining micro-pores, micro-grooves and other micro-textures; Abrasive water jet machining has higher processing efficiency and can process large complex components. EDM equipment investment is cheap, good at processing thin-plate components and deep cavity groove. Special processioning techniques are neither exclusive nor substitutes for each other, but should complement each other and give play to their advantages to produce complex components with high efficiency and precision.

Key words: silicon carbide, ceramic matrix composites, non traditional machining

CLC Number:

V261

ZHANG Xiufeng, SHAO Guodong, LIU Chuancheng, SHI Zhenyu, ZOU Bin, WANG Jilai, ZHANG Chengpeng. Special Processing Techniques Commonly Used For Silicon Carbide Ceramic-Based Composites: Review[J]. Journal of Mechanical Engineering, 2023, 59(1): 199-218.

References

[1] BANSAL N. Handbook of ceramic composites[M]. Boston:Kluwer Academic Publishers, 2005.
[2] ARAI, YUTARO, RYO Inoue, et al. Carbon fiber reinforced ultra-high temperature ceramic matrix composites:A review[J]. Ceramics International, 2019, 45(12):14481-14489.
[3] AN Qinglong, CHEN Jie, MING Weiwei. Machining of SiC ceramic matrix composites:A review[J]. Chinese Journal of Aeronautics, 2020, 34(4):540-567.
[4] 杨甜甜, 张典堂, 邱海鹏, 等. SiC_f/SiC纺织复合材料细观结构及力学性能研究进展[J]. 航空材料学报, 2020, 40(5):1-12. YANG Tiantian, ZHANG Diantang, QIU Haipeng, et al. Progress on fine structure and mechanical properties of SiC_f/SiC textile composites[J]. Journal of Aviation Materials, 2020, 40(05):1-12.
[5] 高希光, 韩栋, 宋迎东, 等. 陶瓷基复合材料结构的动力学强度设计方法:研究现状及展望[J]. 机械工程学报, 2021, 57(16):235-247. GAO Xiguang, HAN Dong, SONG Yingdong, et al. Design method of dynamic strength of ceramic matrix composite structure:Research status and prospect[J]. Journal of Mechanical Engineering, 2021, 57(16):235-247.
[6] EVANS A G, ZOK F W. The physics and mechanics of fibre-reinforced brittle matrix composites[J]. Journal of Materials Science, 2004, 29(15):3857-3896.
[7] NAKANO K, KAMIYA, OGAWA A, et al. Fabrication and mechanical properties of carbon fiber reinforced silicon carbide composites[J]. Nihon Seramikkusu Kyōkai Gakujutsu Ronbunshi, 1992, 100(1160):472-475,.
[8] LIU Qiaomu, HUANG Shunzhou, HE Aijie. Application requirements and challenges of CMC-SiC composites on aero-engine[J]. Journal of Materials Engineering, 2019, 47(2):1.
[9] 邹豪, 王宇, 刘刚, 等. 碳化硅纤维增韧SiC-CMC的发展现状及其在航空发动机上的应用[J]. 航空制造技术, 2017, (15):76-84, 91. ZOU Hao, WANG Yu, LIU Gang, et al. Development status of SiC fiber reinforced SiC ceramic matrix composites and their application in aero-engine[J]. Aeronautical Manufacturing Technology, 2017, (15):76-84, 91.
[10] 黄红岩, 苏力军, 雷朝帅, 等. 可重复使用热防护材料应用与研究进展[J]. 航空学报, 2020, 41(12):6-40. HUANG Hongyan, SU Lijun, LEI Chaoshuai, et al. Application and research progress of reusable thermal protective materials[J]. Acta Aeronautica et Astronautica Sinica, 2020, 41(12):6-40.
[11] MAHAJAN, YASHWANT R, ROY J. Handbook of advanced ceramics and composites:Defense, security, aerospace and energy applications[M]. Cham:Springer International Publishing AG, 2020.
[12] FAN Shangwu, ZHANG Litong, CHENG Laifei, et al. Effect of braking pressure and braking speed on the tribological properties of C/SiC aircraft brake materials[J]. Composites Science and Technology, 2010, 70(6):959-965.
[13] DIAZ O G, GARCIA L, LIAO L, et al. The new challenges of machining ceramic matrix composites (CMCs):Review of surface integrity[J]. International Journal of Machine Tools & Manufacture, 2019, 139:24-36.
[14] R TETI. Machining of composite materials[J]. CIRP Annals, 2002, 51(2):611-634.
[15] RAYAT M S, GRILL S S, RUPINDER S, et al. Fabrication and machining of ceramic composites-A review on current scenario[J]. Materials and Manufacturing Processes, 2017, 32(13):1451-1474.
[16] DIAZ O G, AXINTE D A. Towards understanding the cutting and fracture mechanism in Ceramic Matrix Composites[J]. International Journal of Machine Tools & Manufacture, 2017, 118-119:12-25.
[17] 殷景飞, 徐九华, 丁文锋, 等. SiC_f/SiC陶瓷基复合材料单颗磨粒磨削试验研究[J]. 中国机械工程, 2022, 33(15):1765-1771. YIN Jingfei, XU Jiuhua, DING Wenfeng, et al. Study of SiC_f/SiC ceramic matrix composite[J]. China Mechanical Engineering, 2022, 33(15):1765-1771.
[18] LAWN B R, EVANS A G, MARSHALL D B. Elastic/Plastic indentation damage in ceramics:the median/radial crack system[J]. Journal of the American Ceramic Society, 1980, 63(9-10):574-581.
[19] MARSHALL D B, LAWN B R, EVANS A G. Elastic/Plastic indentation damage in ceramics:the lateral crack system[J]. Journal of the American Ceramic Society, 1982, 65(11):561-566.
[20] BLACKLEY W S, SCATTERGOOD R O. Ductile-regime machining model for diamond turning of brittle materials[J]. Precision Engineering, 1991, 13(2):95-103.
[21] 史振宇. 基于最小切除厚度的微切削加工机理研究[D]. 济南:山东大学, 2011. SHI Zhenyu. Research on micro-cutting mechanism based on minimum cutting thickness[D]. Jinan:Shandong University, 2011.
[22] LI Yuanchen, GE Xiang, WANG Hui, et al. Study of material removal mechanisms in grinding of C/SiC composites via single-abrasive scratch tests[J]. Ceramics International, 2019, 45(4):4729-4738.
[23] ARIF M, ZHANG Xianquan, RAHMAN M, et al. A predictive model of the critical undeformed chip thickness for ductile-brittle transition in nano-machining of brittle materials[J]. International Journal of Machine Tools & Manufacture, 2013, 64:114-122.
[24] ZONG W J, CAO Z M, HE C, et al.. Critical undeformed chip thickness of brittle materials in single point diamond turning[J]. International Journal of Advanced Manufacturing Technology, 2015, 81(5):975-984.
[25] 王晶, 成来飞, 刘永胜, 等. SiC-CMC加工技术研究进展[J]. 航空制造技术, 2016, (15):50-56. WANG Jing, CHENG Laifei, LIU Yongsheng, et al. Research progress on fabrication technology of silicon carbide ceramic matrix composites[J]. Aeronautical Manufacturing Technology, 2016, (15):50-56(in Chinese).
[26] XING Youqiang, DENG Jianxin, ZHANG Guodong, et al. Assessment in drilling of C/C-SiC composites using brazed diamond drills[J]. Journal of Manufacturing Processes, 2017, 26:31-43.
[27] ZOU Fan, CHEN Jie, AN Qingling, et al. Influences of clearance angle and point angle on drilling performance of 2D C_f/SiC composites using polycrystalline diamond tools[J]. Ceramics International, 2020, 46(4):4371-4380.
[28] CHEN Jie, AN Qinglong, MING Weiwei, et al. Hole exit quality and machined surface integrity of 2D C_f/SiC composites drilled by PCD tools[J]. Journal of the European Ceramic Society, 2019, 39(14):4000-4010.
[29] 谢巍杰, 邱海鹏, 陈明伟. SiC_f/SiC陶瓷基复合材料制孔工艺[J]. 宇航材料工艺, 2016, 46(5):50-53. XIE Weijie, QIU Haipeng, CHEN Mingwei. Drilling process of SiC_f/SiC ceramic matrix composites[J]. Astronautical Materials & Technology, 2016, 46(5):50-53.
[30] DIAZ O G, AXINTE D A, NOVOVIC D. Probabilistic modelling of tool unbalance during cutting of hard-heterogeneous materials:A case study in ceramic matrix composites(CMCs)[J]. Composites. Part B, Engineering, 2018, 148:217-226, 2018.
[31] DIAZ O G, AXINTE D A, BUTLER S P, et al. On understanding the microstructure of SiC/SiC Ceramic Matrix Composites (CMCs) after a material removal process[J]. Materials Science & Engineering. A, Structural Materials:Properties, Microstructure and Processing, 2019, 743:1-11.
[32] 张瑾瑜, 王宁, 赵建设, 等. C/SiC复合材料螺旋铣削与钻削制孔效果对比[J]. 宇航材料工艺, 2020, 50(5):39-43. ZHANG Jinyu, WANG Ning, ZHAO Jianshe, et al. Comparison of spiral milling and drilling of C/SiC composite[J]. Aerospace Material Process, 2020, 50(5):39-43.
[33] HU Meng, MING Weiwei, AN Qinglong, et al. Experimental study on milling performance of 2D C/SiC composites using polycrystalline diamond tools[J]. Ceramics International, 2019, 45(8):10581-10588.
[34] 陈杰, 安庆龙, 明伟伟, 等. PCD刀具几何参数对Cf/SiC复合材料铣削质量的影响[J]. 工具技术, 2020, 54(10):3-8. CHEN Jie, AN Qinglong, MING Weiwei, et al. PCD effect of tool geometry parameters on milling quality of Cf/SiC composites[J].] Tool Technology, 2020, 54(10):3-8.
[35] TASHIRO T, FUJIWARA J, TAKENAKA Y. Grinding of C/C-SiC composite in dry method[M]. London:Springer, 2007:351-352.
[36] DU Jinguang, MING Wuyi, MA Jun, et al. New observations of the fiber orientations effect on machinability in grinding of C/SiC ceramic matrix composite[J]. Ceramics International, 2018, 44(12):13916-13928.
[37] 丁凯, 傅玉灿, 苏宏华, 等. C/SiC复合材料组织对磨削力与加工表面质量的影响[J]. 中国机械工程, 2013, 24(14):1886-1890. DING Kai, FU Yucan, SU Honghua, et al. The influence of C/SiC composites structure on grinding force and surface quality[J]. China Mechanical Engineering, 2013, 24(14):1886-1890.
[38] 屈硕硕, 巩亚东, 杨玉莹, 等. 单向碳纤维增强陶瓷基复合材料磨削表面质量研究[J]. 东北大学学报, 2019, 40(9):1310-1315. QU Shuoshuo, GONG Yadong, YANG Yuying, et al. Grinding surface quality of unidirectional carbon fiber reinforced ceramic matrix composites[J]. Study Journal of Northeast University, 2019, 40(9):1310-1315.
[39] 张立峰, 王盛, 李战, 等. 纤维方向对单向C/SiC复合材料磨削加工性能的影响[J]. 中国机械工程, 2020, 31(3):373-377. ZHANG Lifeng, WANG Sheng, LI Zhan, et al. Tthe influence of fiber direction on grinding properties of unidirectional C/siC composites[J]. China Mechanical Engineering, 2020, 31(3):373-377.
[40] YANG Yuying, QU Shuoshuo, GONG Yadong. Investigating the grinding performance of unidirectional and 2.5D C/SiCs[J]. Ceramics International, 2021, 47(4):5123-5132.
[41] GARCIA L G, AXINTE D, NOVOVIC D. Influence of grit geometry and fibre orientation on the abrasive material removal mechanisms of SiC/SiC Ceramic Matrix Composites (CMCs)[J]. International Journal of Machine Tools & Manufacture, 2020, 157:103580.
[42] ESMAEILI H, ADIBI H, REZAEI S M. An efficient strategy for grinding carbon fiber-reinforced silicon carbide composite using minimum quantity lubricant[J]. Ceramics International, 2019, 45(8):10852-10864.
[43] QU Shuoshuo, GONG Yadong, YANG Yuying, et al. Investigating minimum quantity lubrication in unidirectional Cf/SiC composite grinding[J]. Ceramics International, 2020, 46(3):3582-3591.
[44] ZHANG Lifeng, REN Chengzu, JI Chunhui, et al. Effect of fiber orientations on surface grinding process of unidirectional C/SiC composites[J]. Applied Surface Science, 2016, 366:424-431.
[45] TAWAKOLI T, AZARHOUSHANG B. Intermittent grinding of ceramic matrix composites (CMCs) utilizing a developed segmented wheel[J]. International Journal of Machine Tools & Manufacture, 2011, 51(2):112-119.
[46] LIU Qiong, HUANG Guoqin, XU Xipeng, et al. A study on the surface grinding of 2D C/SiC composites[J]. International Journal of Advanced Manufacturing Technology, 2017, 93(5):1595-1603.
[47] QU Shuoshuo, GONG Yadong, YANG Yuying, et al. Surface topography and roughness of silicon carbide ceramic matrix composites[J]. Ceramics International, 2018, 44(12):14742-14753.
[48] TETI R. Machining of Composite Materials[J]. CIRP Annals, 2002, 51(2):611-634.
[49] LIU Defu, TANG Yongjun. A review of mechanical drilling for composite laminates[J]. Composite Structures, 2012, 94(4):1265-1279.
[50] DANDEKAR C R, SHIN Y C. Modeling of machining of composite materials:A review[J]. International Journal of Machine Tools & Manufacture, 2012, 57:102-121.
[51] RAYAT M. S, GRILL S S, SINGH R, et al. Fabrication and machining of ceramic composites-A review on current scenario[J]. Materials and Manufacturing Processes, 2017, 32(13):1451-1474.
[52] DIAZ O G, GARCIA L G, LIAO Zhirong, et al. The new challenges of machining Ceramic Matrix Composites (CMCs):Review of surface integrity[J]. International Journal of Machine Tools & Manufacture, 2019, 139:24-36.
[53] LV Xinyuan, YE Fang, CHENG Lafei, et al. Fabrication of SiC whisker-reinforced SiC ceramic matrix composites based on 3D printing and chemical vapor infiltration technology[J]. Journal of the European Ceramic Society, 2019, 39(11):3380-3386.
[54] ZHU Wei, FU Hua, XU Zhongfeng, et al. Fabrication and characterization of carbon fiber reinforced SiC ceramic matrix composites based on 3D printing technology[J]. Journal of the European Ceramic Society, 2018, 38(14):4604-4613.
[55] 王欢. 快速成型SiC陶瓷基复合材料及其性能研究[D].西安:西安理工大学, 2019. WANG Huan. Rapid prototyping of SiC ceramic matrix composites and their properties[J]. Xi'an:Xi'an University of Technology, 2019.
[56] 徐俊杰. SiC_f/SiC复合材料的水导激光加工工艺基础研究[D]. 哈尔滨:哈尔滨工业大学, 2019. XU Junjie. Laser fabrication of SiC/SiC composites by water guided laser[J]. Harbin:Harbin Institute of Technology, 2019.
[57] XU Liang, ZHAO Guolong, ZHANG Jianqiang, et al. Study on low temperature milling of carbon fiber reinforced SiC matrix composites[J]. Transactions of Nanjing University of Aeronautics and Astronautics, 2020, 37(3):424-433.
[58] 徐亮, 王凯, 王新永, 等. C_f/SiC复合材料低温铣削工艺优化研究[J]. 机械制造与自动化, 2021, 50(1):36-40. XU Liang, WANG Kai, WANG Xinyong, et al. Study on optimization of low temperature milling process of Cf/SiC composites[J]. Mechanical Manufacturing and Automation, 2021, 50(1):36-40.
[59] KIM K, KIM J, CHOI J, et al. A review on research and development of laser assisted turning[J]. International Journal of Precision Engineering and Manufacturing, 2011, 12(4):753-759.
[60] ROZZI J C, BARTON M D. The laser-assisted edge milling of ceramic matrix composites[C]//Proceedings of the ASME International Manufacturing Science and Engineering Conference 2009, 2009.
[61] RAO Xiaoshuang, ZHANG Feihu, LU Yanjun, et al. Analysis of diamond wheel wear and surface integrity in laser-assisted grinding of RB-SiC ceramics[J]. Ceramics International, 2019, 45(18):24355-24364.
[62] ZHOU Kun, XU Jiayu, XIAO Guijian, et al. A novel low-damage and low-abrasive wear processing method of C_f/SiC ceramic matrix composites:Laser-induced ablation-assisted grinding[J]. Journal of Materials Processing Technology, 2022, 302.
[63] CHEN Jie, MING Weiwei, AN Qinglong, et al. Mechanism and feasibility of ultrasonic-assisted milling to improve the machined surface quality of 2D C_f/SiC composites[J]. Ceramics International, 2020, 46(10):15122-15136.
[64] HOCHENG H, TAI N H, LIU C S. Assessment of ultrasonic drilling of C/SiC composite material[J]. Composites. Part A, Applied Science and Manufacturing, 2000, 31(2):133-142.
[65] DING Kai, FU Yucan, SU Honghua, et al. Study on surface/subsurface breakage in ultrasonic assisted grinding of C/SiC composites[J]. International Journal of Advanced Manufacturing Technology, 2017, 91(9):3095-3105.
[66] 康仁科, 赵凡, 鲍岩, 等. 超声辅助磨削SiC_f/SiC陶瓷基复合材料[J]. 金刚石与磨料磨具工程, 2019, 39(04):85-91. KANG Renke, ZHAO Fan, BAO Yan, et al. Ultrasonic assisted grinding of SiC_f/SiC ceramic matrix composites[J]. Diamond & Abrasives Engineering, 2019, 39(04):85-91.
[67] YOU Kaiyuan, YAN Guangpeng, LUO Xichun, et al. Advances in laser assisted machining of hard and brittle materials[J]. Journal of Manufacturing Processes, 2020, 58:677-692.
[68] 翟兆阳, 梅雪松, 王文君, 等. 碳化硅陶瓷基复合材料激光刻蚀技术研究进展[J]. 中国激光, 2020, 47(6):24-34. ZHAI Zhaoyang, MEI Xuesong, WANG Wenjun, et al. Progress on laser etching technology of silicon carbide ceramic matrix composite materials[J]. China laser, 2020, 47(6):24-34.
[69] 樊华. 基于飞秒激光光场调制技术的硬脆材料微纳加工技术研究[D]. 长春:吉林大学, 2020. FAN Hua. Research on micro/nano machining technology of hard and brittle-based on femtosecond laser field modulation technology[D]. Changchun:Jilin University, 2020.
[70] TUERSLEY I P, HOULT T P, PASHBY I R. The processing of SiC/SiC ceramic matrix composites using a pulsed Nd-YAG laser:Part I:Optimisation of pulse parameters[J]. Journal of Materials Science, 1998, 33(4):955-961.
[71] WANG Chunhui, ZHANG Litong, LIU Yongsheng, et al. Ultra-short pulse laser deep drilling of C/SiC composites in air[J]. Applied Physics A, 2013, 111(4):1213-1219.
[72] 刘瑞军, 桓恒, 赵晨曦, 等. 超短脉冲激光加工陶瓷基复合材料制孔研究[J]. 电加工与模具, 2019, (2):55-58. LIU Ruijun, HUAN Heng, ZHAO Chenxi, et al. A study on poremaking of ceramic matrix composites by ultra-short pulse laser processing[J]. Electrical Processing and Mould, 2019, (2):55-58.
[73] 蔡敏, 张晓兵, 张伟, 等. SiC/SiC复合材料纳秒激光和皮秒激光制孔质量的对比研究[J]. 航空制造技术, 2016, (19):52-55. CAI Min, ZHANG Xiaobing, ZHANG Wei, et al. Comparative study on the pore quality of nanosecond laser and picosecond laser for SiC/SiC composites[J]. and Aviation Manufacturing Technology, 2016, (19):52-55.
[74] LIU Yanchi, WU Chenwu, HUANG Yihui, et al. Interlaminar damage of carbon fiber reinforced polymer composite laminate under continuous wave laser irradiation[J]. Optics and Lasers in Engineering, 2017, 88:91-101.
[75] ZHANG Ruoheng, LI Weinan, LIU Yongsheng, et al. Machining parameter optimization of C/SiC composites using high power picosecond laser[J]. Applied Surface Science, 2015, 330:321-331.
[76] ZHAI Zhaoyang, WANG Weijun, ZHAO Jie, et al. Influence of surface morphology on processing of C/SiC composites via femtosecond laser[J]. Composites Part A, Applied Science and Manufacturing, 2017, 102:117-125.
[77] LIU Yongsheng, WANG Chunhui, LI Weinan, et al. Effect of energy density and feeding speed on micro-hole drilling in C/SiC composites by picosecond laser[J]. Journal of Materials Processing Technology, 2014, 214(12):3131-3140.
[78] ZHAI Zhaoyang, WANG Wenjun, MEI Xuesong, et al. Effect of the surface microstructure ablated by femtosecond laser on the bonding strength of EBCs for SiC/SiC composites[J]. Optics Communications, 2018, 424:137-144.
[79] LI Weinan, ZHANG Ruoheng, LIU Yongheng, et al. Effect of different parameters on machining of SiC/SiC composites via pico-second laser[J]. Applied Surface Science, 2016, 364:378-387,.
[80] YALUKOVA O, SARADY I. Investigation of interaction mechanisms in laser drilling of thermoplastic and thermoset polymers using different wavelengths[J]. Composites Science and Technology, 2006, 66(10):1289-1296.
[81] NEGARESTANI R. Nano-second pulsed DPSS Nd:YAG laser cutting of CFRP composites with mixed reactive and inert gases[J]. International Journal of Advanced Manufacturing Technology, 2010, 49(5):553-566.
[82] 焦浩文, 陈冰, 罗良, 等. 纳秒激光加工2.5维Cf/SiC复合材料的烧蚀孔洞特征[J].中国机械工程, 2020, 31(8):983-990. JIAO Haowen, CHEN Bing, LUO Liang, et al. Characteristics of ablation holes in 2.5-dimensional Cf/SiC composites by nanosecond laser processing[J]. China Mechanical Engineering, 2020, 31(8):983-990.
[83] MELENTIEV R, FANG Fengzhou. Recent advances and challenges of abrasive jet machining[J]. CIRP Journal of Manufacturing Science and Technology, 2018, 22:1-20.
[84] NATARAJAN Y. Abrasive water jet machining process:A state of art of review[J]. Journal of Manufacturing Processes, 2020, 49:271-322.
[85] 任云明. 磨料水射流加工结构陶瓷及陶瓷基复合材料的研究[J]. 内燃机与配件, 2018, (15):116-118. REN Yunming. Study on abrasive waterjet processing of structural ceramics and ceramic matrix composites[J]. Internal Combustion Engines and Accessories, 2018, (15):116-118.
[86] HASHISH M. Turning with abrasive-waterjets-a first investigation[J]. Journal of Engineering for Industry, 1987, 9(4):281-290.
[87] DENG Jianxin, FENG Yihua, DING Zeliang, et al.. Wear behavior of ceramic nozzles in sand blasting treatments[J]. Journal of the European Ceramic Society, 2003, 23(2):323-329.
[88] DENG Jianxin, WU Fengfang, ZHAO Jinlong. Wear mechanisms of gradient ceramic nozzles in abrasive air-jet machining[J]. International Journal of Machine Tools & Manufacture, 2007, 47(12):2031-2039.
[89] DENG Jianxin, LIU Lili, DING Mingwei. Gradient structures in ceramic nozzles for improved erosion wear resistance[J]. Ceramics International, 2007, 33(7):1255-1261.
[90] DENG Jianxin, LIU Lili, DING Mingwei. Effect of residual stresses on the erosion wear of laminated ceramic nozzles[J]. Materials Characterization, 2008, 59(1):1-8.
[91] HASHISH M., KOTCHON A, RAMULU M. Status of AWJ machining of CMCS and hard materials[C]//INTERTECH 2015, Indianapolis, India.
[92] HASHISH M. Observations of wear of abrasive-waterjet nozzle materials[J]. Journal of Tribology, 1994, 116(3):439-444.
[93] NANDURI M, TAGGART D G, KIM T J. The effects of system and geometric parameters on abrasive water jet nozzle wear[J]. International Journal of Machine Tools & Manufacture, 2002, 42(5):615-623.
[94] DENG Jianxin. Erosion wear of boron carbide ceramic nozzles by abrasive air-jets[J]. Materials Science & Engineering. A, Structural Materials:Properties, Microstructure and Processing, 2005, 408(1):227-233.
[95] RAMULU M, JENKINS M G, GUO Z. Abrasive water jet machining mechanisms in continuous-fiber ceramic composites[J]. Journal of Composites Technology & Research, 2001, 23(2):82-91.
[96] DENG Jianxin, ZHANG Xihua, NIU Pingzhang, et al. Wear of ceramic nozzles by dry sand blasting[J]. Tribology International, 2006, 39(3):274-280.
[97] KORDONSKI W, SHOREY A. Magnetorheological (MR) jet finishing technology[J]. Journal of Intelligent Material Systems and Structures, 2007, 18(12):1127-1130.
[98] JHA S, JAIN V K. Design and development of the magnetorheological abrasive flow finishing (MRAFF) process[J]. International Journal of Machine Tools & Manufacture, 2004, 44(10):1019-1029.
[99] TRICARD M, KORDONSKI W, SHOREY A B, et al. Magnetorheological jet finishing of conformal, freeform and steep concave optics[J]. CIRP Annals, 2006, 55(1):309-312.
[100] KORDONSKI W, SHOREY A B, SEKERES A. New magnetically assisted finishing method:Material removal with magnetorheological fluid jet[C]//Proceedings of SPIE, 2004.
[101] KORDONSKI W, SHOREY A B, TRICARD M. Jet-induced high-precision finishing of challenging optics[C]//Proceedings of SPIE, 2005.
[102] PACHAURY Y, TANDON P. An overview of electric discharge machining of ceramics and ceramic based composites[J]. Journal of Manufacturing Processes, 2017, 25:369-390.
[103] FUKUZAWA Y, MOHRI N, GOTOH H, et al. Three-dimensional machining of insulating ceramics materials with electrical discharge machining[J]. Transactions of Nonferrous Metals Society of China, 2009, 19(z1):150-156.
[104] 魏臣隽, 刘剑, 许正昊, 等. 纤维强化陶瓷复合材料的电火花加工[J]. 电加工与模具, 2015, (1):25-29, 33. WEI Chenjun, LIU Jian, XU Zhenghao, et al. EDM for fiber reinforced ceramic composites[J]. Electrical Machining and Mould, 2015, (1):25-29, 33.
[105] HOCHENG H, GUU Y H, TAI N H. The feasibility analysis of electrical-discharge machining of carbon-carbon composites[J]. Materials and Manufacturing Processes, 1998, 13(1):117-132.
[106] HE Wenbin, HE Shaotai, DU Jinguang, et al. Fiber orientations effect on process performance for wire cut electrical discharge machining (WEDM) of 2D C/SiC composite[J]. International Journal of Advanced Manufacturing Technology, 2019, 102(1):507-518.
[107] YUE Xiaoming, LI Qi, YANG Xiaodong. Influence of thermal stress on material removal of C_f/SiC composite in EDM[J]. Ceramics International, 2020, 46(6):7998-8009.
[108] KÖNIG W, DAUW D F, LEVY G, et al. EDM-future steps towards the machining of ceramics[J]. CIRP Annals, 1988, 37(2):623-631.
[109] CALIGNANO F, DENTI L, BASSOLI E, et al. Studies on electrodischarge drilling of an Al₂O₃-TiC composite[J]. International Journal of Advanced Manufacturing Technology, 2013, 66(9):1757-1768.
[110] LIEW P J, YAN J, KURIYAGAWA T. Carbon nanofiber assisted micro electro discharge machining of reaction-bonded silicon carbide[J]. Journal of Materials Processing Technology, 2013, 213(7):1076-1087.
[111] LUIS C J, PUERTAS I, VILLA G. Material removal rate and electrode wear study on the EDM of silicon carbide[J]. Journal of Materials Processing Technology, 2005, 164-165:889-896.
[112] CLIJSTERS S, LIU K, REYNAERTS D, et al. EDM technology and strategy development for the manufacturing of complex parts in SiSiC[J]. Journal of Materials Processing Technology, 2010, 210(4):631-641.
[113] WEI Chenjun, ZHAO Li, HU Dejin, et al. Electrical discharge machining of ceramic matrix composites with ceramic fiber reinforcements[J]. International Journal of Advanced Manufacturing Technology, 2013, 64(1):187-194.
[114] 马长进. ZrB_2-SiC陶瓷电火花单脉冲放电蚀除凹坑仿真与加工试验研究[D]. 哈尔滨:哈尔滨工业大学, 2016. MA Changjin. Simulation and Experimental Study on Machining of ZrB_2-SiC Ceramics by EDM Monopulse Erosion[D]. Harbin:Harbin Institute of Technology, 2016.
[115] TSUTSUMI C, OKANO K, SUTO T. High quality machining of ceramics[J]. Journal of Materials Processing Technology, 1993, 37(1):639-654.
[116] 郭永丰, 黄荣和, 李常伟, 等. 非导电材料的电化学电火花复合加工工艺研究[J]. 电加工, 1998(6):23-25. GUO Yongfeng, HUANG Ronghe, LI Changwei, et al. Research on electrochemical edm composite machining technology of non-conductive materials[J]. Electromachining, 1998(6):23-25.
[117] FUKUZAWA Y, TANI T, IWANE E, et al. New machining method for insulating ceramics with an electrical discharge phenomenon[J]. Nihon Seramikkusu Kyōkai Gakujutsu Ronbunshi, 1995, 103(1202):1000-1005.
[118] MOHRI N, FUKUZAWA Y, TANI T, et al. Assisting electrode method for machining insulating ceramics[J]. CIRP Annals, 1996, 45(1):201-204.
[119] HANAOKA D, FUKUZAWA Y, YAMASHITA K. Research of large-area electrical discharge machining for insulating Si3N4 ceramics with the assisting electrode method[C]//Advanced Materials Research, 2014.
[120] ZELLER F, HOSEL T, MULLER C, et al. Microstructuring of non-conductive silicon carbide by electrical discharge machining[J]. Microsyste Technologies, 2014, 20(10):1875-1880.
[121] FUKUZAWA Y. Mechanical strength of the wire EDMed insulating ZrO₂ceramics by assisting electrode method[C]//Proceedings of the 15th International Symposium on Electromachining, ISEM, 2007.
[122] GEORGE P M, RAGHUNATH B K, MANOCHA L M, et al. EDM machining of carbon-carbon composite-a Taguchi approach[J]. Journal of Materials Processing Technology, 2004, 145(1):66-71.
[123] CHIANG K. Modeling and analysis of the effects of machining parameters on the performance characteristics in the EDM process of Al₂O₃+TiC mixed ceramic[J]. International Journal of Advanced Manufacturing Technology, 2008, 37(5-6):523-533.
[124] GUU Y H, HOCHENG H, TAI N H, et al. Effect of electrical discharge machining on the characteristics of carbon fiber reinforced carbon composites[J]. Journal of Materials Science, 2001, 36(8):2037-2043.
[125] LAUWERS B, KRUTH J P, LIU W, et al. Investigation of material removal mechanisms in EDM of composite ceramic materials[J]. Journal of Materials Processing Technology, 2004, 149(1-3):347-352.
[126] PATEL K M, PANDEY P M, RAO P V. Optimisation of process parameters for multi-performance characteristics in EDM of Al₂O₃ ceramic composite[J]. International Journal of Advanced Manufacturing Technology, 2010, 47(9-12):1137-1147,.
[127] PATEL K M, PANDEY P M, RAO P V. Determination of an optimum parametric combination using a surface roughness prediction model for EDM of Al₂O₃/SiCw/TiC ceramic composite[J]. Materials and Manufacturing Processes, 2009, 24(6):675-682.
[128] SATYARTHI M K, PANDEY P M. Comparison of edg diamond grinding and EDM processing of conductive alumina ceramic composite[J]. Materials and Manufacturing Processes, 2013, 28(4):369-374.