静电喷雾磨粒均布微结构磨具原位制备研究

doi:10.3901/JME.2021.07.262

机械工程学报 ›› 2021, Vol. 57 ›› Issue (7): 262-272.doi: 10.3901/JME.2021.07.262

• 制造工艺与装备 • 上一篇

扫码分享

静电喷雾磨粒均布微结构磨具原位制备研究

陈逢军^1,2, 陈海臻^1,2

1. 湖南大学国家高效磨削工程技术研究中心长沙 410082;
2. 湖南大学机械与运载工程学院长沙 410082

收稿日期:2020-06-25 修回日期:2020-10-19 出版日期:2021-04-05 发布日期:2021-05-25
通讯作者: 陈逢军(通信作者),男,1979年出生,副教授,博士研究生导师。主要研究方向为超精密加工与控制,微结构制造。E-mail:abccfj@126.com
基金资助:
国家自然科学基金资助项目(51975204,51805159)。

In-situ Fabrication of Microstructure Tool with Abrasive Uniform by Electrostatic Spray Deposition

CHEN Fengjun^1,2, CHEN Haizhen^1,2

1. National Engineering Research Center for High Efficiency Grinding, Hunan University, Changsha 410082;
2. College of Mechanical and Vehicle Engineering, Hunan University, Changsha 410082

Received:2020-06-25 Revised:2020-10-19 Online:2021-04-05 Published:2021-05-25

摘要/Abstract

摘要： 提出一种基于静电喷雾的磨粒均布微结构磨具原位制备方法。使用COMSOL Multiphysics中的AC/DC模块与粒子追踪模块建立静电喷雾微槽二维仿真模型，研究在喷嘴-环形电极配置下的电场特性、喷雾特性以及沉积特性，获得微槽深径比≤1，微槽深度≤1 mm，静电压≤-6 kV以及接收距离≥40 mm的优化参数。利用光固化树脂、聚山梨酯-80以及煤油按4:3:1的比例制备静电液，并添加单晶金刚石磨粒进行静电喷雾。创新性地利用狄利克雷镶嵌法定量评估不同喷射时间、不同径向位置的磨粒分布均匀度，以喷射中心半径2.5 mm范围内磨粒分布均匀度在70%以上，得到合适的微结构模具尺寸。通过分析微槽深度和宽度对沉积率的影响获得合理的微槽参数。原位制备得到的微结构磨具微观特征完整，磨具与工件微槽宽度偏差率为≤2.87%，高度偏差率为≤1.09%。利用静电喷雾制备微结构磨具具有磨粒均布、形态可控等特点，该方法为微结构表面加工提供新工艺与新思路。

关键词: 静电喷雾, 微结构磨具, 金刚石微粉, 均匀分布, COMSOL Multiphysics

Abstract: A method of in-situ fabrication of microstructure tool with abrasive uniform by ESD is proposed. Two dimensional simulation model of electrostatic spray microgroove is established by using AC/DC module and particle tracking module in COMSOL Multiphysics. The electric field characteristics, spray characteristics and deposition characteristics under nozzle-ring electrodes are studied. The optimized parameters of microgroove height to width ratio ≤1, micro channel depth ≤1 mm, electrostatic voltage ≤-6 kV and receiving distance ≥40 mm are obtained. The static liquid is prepared by light curing resin, polysorbate-80 and kerosene in the proportion of 4:3:1, and the single crystal diamond powder is added for electrostatic spraying. Dirichlet tessellation is used to evaluate the distribution uniformity of abrasive particles in different injection time and radial positions. It was concluded that the distribution uniformity of abrasive particles is more than 70% in the radius range of 2.5 mm with the injection center to obtain the appropriate size of the microstructure tool. The reasonable parameters of the microgroove are obtained by analyzing the influence of the depth and width of the microstructure on the deposition rate. The microstructural characteristics of the abrasive tool are complete. The deviation between the microgroove width of the abrasive tool and the workpiece is ≤2.87%, and the height deviation is ≤1.09%. The in-situ fabrication of microstructure abrasives tool by ESD has the characteristics with uniform distribution of abrasive particles and controllable morphology. This method provides a new idea and technology for microstructure surface machining.

Key words: electrostatic spray deposition, microstructure abrasive tool, diamond powder, uniform distribution, COMSOL Multiphysics

中图分类号:

TG58

陈逢军, 陈海臻. 静电喷雾磨粒均布微结构磨具原位制备研究[J]. 机械工程学报, 2021, 57(7): 262-272.

CHEN Fengjun, CHEN Haizhen. In-situ Fabrication of Microstructure Tool with Abrasive Uniform by Electrostatic Spray Deposition[J]. Journal of Mechanical Engineering, 2021, 57(7): 262-272.

参考文献

[1] SIDORENKO D,MISHNAEVSKY L,LEVASHOV E,et al. Carbon nanotube reinforced metal binder for diamond cutting tools[J]. Materials & Design,2015,83:536-544.
[2] YANG Z,ZHANG M,ZHANG Z,et al. A study on diamond grinding wheels with regular grain distribution using additive manufacturing (AM) technology[J]. Materials & Design,2016,104:292-297.
[3] LU J,LUO Q F,MAO X Y,et al. Fabrication of a resin-bonded ultra-fine diamond abrasive polishing tool by electrophoretic co-deposition for SiC processing[J]. Precision Engineering,2017,47:353-361.
[4] JIANG C,HUANG J,JIANG Z,et al. Estimation of energy savings when adopting ultrasonic vibration-assisted magnetic compound fluid polishing[J]. International Journal of Precision Engineering and Manufacturing-Green Technology,2021,8:1-11.
[5] CHEN F,CHEN H,ZHANG L,et al. Controllable distribution of ultrafine diamond particles by electrostatic spray deposition[J]. Powder Technology,2019,345:267-273.
[6] 陈逢军,张磊,尹韶辉,等. 基于静电喷雾的金刚石磨粒微表面均布特性研究[J]. 表面技术,2018,47(7):15-20. CHEN Fengjun,ZHANG Lei,YIN Shaohui,et al. Uniform distribution characteristic of fine diamond abrasive particles based on high voltage electrostatic spraying[J]. Surface Technology,2018,47(7):15-20.
[7] 陈远流. 面向微结构阵列的超精密切削加工与测量关键技术研究[J]. 机械工程学报,2016,52(5):21. CHEN Yuanliu. Research on the key technologies of ultra precision machining and measurement for micro structure array[J]. Journal of Mechanical Engineering,2016,52(5):21.
[8] 陈逢军,尹韶辉,胡天,等. 微小非球面光学模具单点斜轴误差补偿磨削[J]. 机械工程学报,2013,49(17):59-64. CHEN Fengjun,YIN Shaohui,HU Tian,et al. Single-point inclined-axis error compensation grinding for small aspheric optical molds[J]. Journal of Mechanical Engineering,2013,49(17):59-64.
[9] CHEN F,HAO S,MIAO X,et al. Numerical and experimental study on low-pressure abrasive flow polishing of rectangular microgroove[J]. Powder Technology,2018,327:215-222.
[10] GUO B,ZHAO Q. Ultrasonic vibration assisted grinding of hard and brittle linear micro-structured surfaces[J]. Precision Engineering,2017,48:98-106.
[11] GUO J,KUM C W,AU K H,et al. New vibration-assisted magnetic abrasive polishing (VAMAP) method for microstructured surface finishing[J]. Optics Express,2016,24(12):13542.
[12] WANG Y,WU Y,NOMURA M. Feasibility study on surface finishing of miniature V-grooves with magnetic compound fluid slurry[J]. Precision Engineering,2016,45:67-78.
[13] WU M,GUO B,ZHAO Q,et al. Precision grinding of a microstructured surface on hard and brittle materials by a microstructured coarse-grained diamond grinding wheel[J]. Ceramics International,2018,44(7):8026-8034.
[14] 赵清亮,孙智源,郭兵. 碳化硅圆柱槽微结构表面的化学机械抛光[J]. 机械工程学报,2015,51(15):183-189. ZHAO Qingliang,SUN Zhiyuan,GUO Bing. Chemical mechanical polishing of micro-structures on SSiC[J]. Journal of Mechanical Engineering,2015,51(15):183-189.
[15] GUO B,WU M,ZHAO Q,et al. Improvement of precision grinding performance of CVD diamond wheels by micro-structured surfaces[J]. Ceramics International,2018,44(14):17333-17339.
[16] CHEN S,LIN S. Development of an extremely thin grinding-tool for grinding microgrooves in optical glass[J],Journal of Materials Processing Technology. 2011,211(10):1581-1589.
[17] CHENG J,WU J. Experimental study on the fabrication method of diamond ultra-small micro-grinding tool[J]. The International Journal of Advanced Manufacturing Technology,2018,97(1-4):1431-1444.
[18] ZHAO S,CASTLE G S P,ADAMIAK K. Comparison of conduction and induction charging in liquid spraying[J]. Journal of Electrostatics,2005,63(6-10):871-876.
[19] 刘建河,李星光,许晏铭. 喷针-环形电极配置对感应荷电喷雾的影响[J]. 排灌机械工程学报,2019,37(6):521-527. LIU Jianhe,LI Xingguang,XU Yanming. Influence of needle-ring electrode configuration on induction charging spray[J]. Journal of Drainage and Irrigation Machinery Engineering,2019,37(6):521-527.
[20] 宋昊,刘战强,史振宇,等. 沟槽与方柱阵列结构的微铣削和加工表面疏水性[J]. 机械工程学报,2016,52(21):198-205. SONG Hao,LIU Zhanqiang,SHI Zhenyu,et al. Micro-end milling and hydrophobic properties of machined surface for microgroove and microarray[J]. Journal of Mechanical Engineering,2016,52(21):198-205.
[21] HSU R,LIAO J,TIEN H,et al. Gas chromatography electrospray ionization mass spectrometry analysis of trimethylsilyl derivatives[J]. Journal of Mass Spectrometry,2016,51(10):883-888.
[22] LIU Q,YANG Y,HUANG M,et al. Durability of a lubricant-infused electrospray silicon rubber surface as an anti-icing coating[J]. Applied Surface Science,2015,346:68-76.
[23] YAN J,LENG Y,GUO Y,et al. Highly conductive graphene paper with vertically aligned reduced graphene oxide sheets fabricated by improved electrospray deposition technique[J]. ACS Applied Materials & Interfaces,2019,11(11):10810-10817.
[24] MARINOV G,STRIJKOVA V,VASILEVA M,et al. Effect of substrate temperature on the microstructural,morphological,and optical properties of electrosprayed Zno thin films[J]. Advances in Condensed Matter Physics,2018,2018:1-7.
[25] GAÑÁN-CALVO A M,DÁVILA J,BARRERO A. Current and droplet size in the electrospraying of liquids. Scaling laws[J]. Journal of Aerosol Science,1997,28(2):249-275.
[26] JUNG J H,OH H,KIM S S. Numerical simulation of the deposition pattern in multiple electrohydrodynamic spraying[J]. Powder Technology,2010,198(3):439-444.
[27] OH H,KIM K,KIM S. Characterization of deposition patterns produced by twin-nozzle electrospray[J]. Journal of Aerosol Science,2008,39(9):801-813.
[28] BRANDENBERGER H,NÜSSLI D,PIËCH V,et al. Monodisperse particle production:a method to prevent drop coalescence using electrostatic forces[J]. Journal of Electrostatics,1999,45(3):227-238.
[29] GAÑAN-CALVO A M,BARRERO A. A global model for the electrospraying of liquids in steady cone-jet mode[J]. Journal of Aerosol Science,1996,27(S1):S179-S180.
[30] ZHANG J,HE H. The motion behavior of a group of charged droplets in liquid-liquid electrostatic spray[J]. Flow Turbulence and Combustion,2012,89(4):675-689.

静电喷雾磨粒均布微结构磨具原位制备研究

In-situ Fabrication of Microstructure Tool with Abrasive Uniform by Electrostatic Spray Deposition

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 3

编辑推荐

Metrics

本文评价

[1]	巩浩, 刘检华, 孙清超, 夏焕雄. 精密机电产品均匀性装配的定义与关键技术[J]. 机械工程学报, 2021, 57(3): 174-184.
[2]	罗天祺, 陈再刚, 蒋建政, 王家鑫, 王开云. 货物非均匀装载对高速货运动车组动力学性能的影响[J]. 机械工程学报, 2021, 57(2): 139-146.
[3]	王军锋;闻建龙;王泽;罗惕乾. 煤油荷电喷雾特性及喷雾流场的试验研究[J]. , 2002, 38(7): 37-40.