电弧增材成形单道两层熔积过程中的晶粒生长模拟

doi:10.3901/JME.2018.22.086

机械工程学报 ›› 2018, Vol. 54 ›› Issue (22): 86-94.doi: 10.3901/JME.2018.22.086

电弧增材成形单道两层熔积过程中的晶粒生长模拟

周祥曼^1,2, 田启华^1,2, 杜义贤^1,2, 柏兴旺³, 张海鸥⁴

1. 三峡大学机械与动力学院宜昌 443002;
2. 水电机械设备设计与维护湖北省重点实验室(三峡大学) 宜昌 443002;
3. 南华大学机械工程学院衡阳 421001;
4. 华中科技大学机械科学与工程学院武汉 430074

收稿日期:2018-04-27 修回日期:2018-08-01 出版日期:2018-11-20 发布日期:2018-11-20
作者简介:周祥曼,男,1983年出生,博士,讲师。主要从事电弧增材制造工艺与多尺度数值模拟的研究。E-mail:zhouxman@ctgu.edu.cn
基金资助:
国家自然科学基金资助项目（51705287，51775308）。

Simulation of Grain Growth in Single-pass Two-layer Deposition of Arc Welding Based Additive Forming Process

ZHOU Xiangman^1,2, TIAN Qihua^1,2, DU Yixian^1,2, BAI Xingwang³, ZHANG Haiou⁴

1. College of Mechanical and Power Engineering, China Three Gorges University, Yichang 443002;
2. Hubei Key Laboratory of Hydroelectric Machinery Design & Maintenance, China Three Gorges University, Yichang 443002;
3. School of Mechanical Engineering, University of South China, Hengyang 421001;
4. School of Mechanical Science & Engineering, Huazhong University of Science and Technology, Wuhan 430074

Received:2018-04-27 Revised:2018-08-01 Online:2018-11-20 Published:2018-11-20

摘要/Abstract

摘要： 晶粒生长的数值模拟是研究复杂微观组织演变的重要手段，现有的研究较少涉及电弧增材成形中晶粒生长的数值模拟。采用有限元和元胞自动机方法建立了碳钢电弧增材成形过程的宏观传热和微观组织演变的耦合模型，模拟单道第两层熔积的熔池凝固过程中晶粒动态演变过程。模拟结果显示，单道第一层熔积熔池凝固过程中晶粒从熔合线位置形核后向熔池中心生长，在温度梯度方向与枝晶臂优先生长方向的共同作用下，枝晶呈现竞争生长，晶粒优先生长方向与温度梯度方向一致的晶粒生长更快，部分晶粒生长被抑制，最终形成交错、完全粗大的柱状晶组织，枝晶之间出现溶质富集的现象；单道第二层熔积的晶粒在上一层粗大柱状晶基础上形核并生长，随后的生长过程与第一层类似，第二层熔积时熔池温度梯度方向的改变导致晶粒的主要生长方向与第一层之间有一定夹角。与模拟相同成形工艺的成形试样金相照片验证了模拟结果。研究结果可为电弧增材成形微观组织控制以及后续工艺规划提供依据和参考。

关键词: 单道两层熔积, 电弧增材成形, 晶粒生长, 数值模拟

Abstract: The numerical simulation of grain growth is an important way to study the evolution of complex microstructure. Studies are less concerned with numerical simulation of grain growth in arc welding based additive forming(AWAM) process. A coupling model of macroscopic heat transfer and microstructure evolution in AWAM process is established by finite element method and cellular automata method. Then, the dynamic evolution of grains during the solidification process of the molten pool is simulated. The simulated results show that the grains nucleate at the fusion line and then grow toward the molten pool center in the first-layer deposition. Under the influence of the temperature gradient direction and crystallographic orientation of the dendritic arms, the competition between the grains becomes strong. When the crystallographic orientation coincides with the temperature gradient direction, the grain growth faster, and the others are inhibited. Ultimately, the grain morphology is characterized by staggered and coarse columnar grains. In adition, the solute enrichment phenomenon appears between the grains. In the second-layer deposition, the grains nucleate on the columnar grains of upper layer, and the subsequent growth process is similar to the upper layer. Beacause the change of temperature gradient direction of molten pool in the second-layer deposition, there is a lilte angle between the main growth direction of the grains between the first-layer and second-layer. The simulated results are verified by metallographic photograph of the experimental test. The conclusions of the above study can provide the basis and reference for the microstructure control and process planning of AWAF process.

Key words: arc welding based additive forming, grain growth, numerical simulation, single-pass two-layer deposition

中图分类号:

TG401
TG44

周祥曼, 田启华, 杜义贤, 柏兴旺, 张海鸥. 电弧增材成形单道两层熔积过程中的晶粒生长模拟[J]. 机械工程学报, 2018, 54(22): 86-94.

ZHOU Xiangman, TIAN Qihua, DU Yixian, BAI Xingwang, ZHANG Haiou. Simulation of Grain Growth in Single-pass Two-layer Deposition of Arc Welding Based Additive Forming Process[J]. Journal of Mechanical Engineering, 2018, 54(22): 86-94.

参考文献

[1] 周祥曼,田启华,杜义贤,等. 纵向稳态磁场对电弧增材成形零件表面质量和性能影响的研究[J]. 机械工程学报,2018,52(2):84-92. ZHOU Xiangman,TIAN Qihua,DU Yixian,et al. Study of the influence of longitudinal static magnetic field on surface quality and performances of arc welding based additive forming parts[J]. Journal of Mechanical Engineering,2018,52(2):84-92.
[2] HASELHUHN A S,BUHR M W,WIJNEN B,et al. Structure-property relationships of common aluminum weld alloys utilized as feedstock for GMAW-based 3-D metal printing[J]. Materials Science and Engineering:A,2016,673:511-523.
[3] 刘奋成,贺立华,林鑫,等. 电弧沉积制造TC4钛合金的组织和力学性能研究[J]. 热加工工艺,2014,43(10):1-5. LIU Fencheng,HE Lihua,LIN Xin,et al. Study on microstructure and mechanical properties of arc deposition manufactured TC4 titanium alloy[J]. Hot Working Technolog,2014,43(10):1-5.
[4] DONOGHUE J,ANTONYSAMY A A,MARTINA F,et al. The effectiveness of combining rolling deformation with Wire-Arc additive manufacture on β-grain refinement and texture modification in Ti-6Al-4V[J]. Materials Characterization,2016,114:103-114.
[5] 徐富家. Inconel625合金等离子弧快速成形组织控制及工艺优化[D]. 哈尔滨:哈尔滨工业大学,2013. XU Fujia. Microstructure control and process optimization of Inconel625 alloy fabricated by plasma arc rapid prototyping[D]. Harbin:Harbin Institute of Technology,2013.
[6] RAPPAZ M,GANDIN C A. Probabilistic modeling of microstructure formation in solidification process[J]. International Materials Reviews,1993,41(1):345-360.
[7] NASTAC L,STEFANESCU D M. Stochastic modelling of microstructure formation in solidification processes[J]. Modelling & Simulation in Materials Science & Engineering,1997,5(4):391-420.
[8] NASTAC L. Numerical modeling of solidification morphologies and segregation patterns in cast dendritic alloys[J]. Acta Materialia,1999,47(17):4253-4262.
[9] ZHAN X H,DONG Z B,WEI Y H,et al. Simulation of grain morphologies and competitive growth in weld pool of Ni-Cr alloy[J]. Journal of Crystal Growth,2009,311(23-24):4778-4783.
[10] 占小红. Ni-Cr二元合金焊接熔池枝晶生长模拟[D]. 哈尔滨:哈尔滨工业大学,2008. ZHAN Xiaohong. Simulation of dendritic grain growth in weld pool of nikel-chromium binary alloy[D]. Harbin:Harbin Institute of Technology,2008.
[11] ZHAN X,WEI Y,DONG Z. Cellular automaton simulation of grain growth with different orientation angles during solidification process[J]. Journal of Materials Processing Technology,2008,208(1-3):1-8.
[12] 马瑞. 镍基合金焊接熔池凝固过程微观组织模拟[D]. 哈尔滨:哈尔滨工业大学,2010. MA Rui. Simulation of microstructure evolution during welding solidifaction of nikel-based alloy[D]. Harbin:Harbin Institute of Technology,2010.
[13] HAN R H,DONG W,LU S,et al. Modeling of morphological evolution of columnar dendritic grains in the molten pool of gas tungsten arc welding[J]. Computational Materials Science,2014,95:351-361.
[14] 韩日宏,董文超,陆善平,等. 宏微观耦合模拟熔池不同区域中枝晶竞争生长过程[J]. 物理学报,2014,63(22):377-388. HAN Rihong,DONG Wenchao,LU Shanping,et al. Macro-micro coupled simulation of competitive dendrite growth in different areas of the welding pool[J]. Acta Physica Sinica,2014,63(22):377-388.
[15] HAN R H,LU S,DONG W,et al. Multi-scale simulation for the columnar to equiaxed transition in the weld pool[J]. ISIJ International,2016,56(6):1003-1012.
[16] SONG K J,WEI Y H,DONG Z B,et al. Numerical simulation of β to α phase transformation in heat affected zone during welding of TA15 alloy[J]. Computational Materials Science,2013,72:93-100.
[17] GUILLEMOT G,CHARLES-ANDRE G,COMBEAU H. Modeling of macrosegregation and solidification grain structures with a coupled cellular automaton-:Finite element model[J]. Isij International,2011,46(6):880-895.
[18] CHEN S,GUILLEMOT G,GANDIN C A. Three-dimensional cellular automaton-finite element modeling of solidification grain structures for arc-welding processes[J]. Acta Materialia,2016,115:448-467.
[19] 赵静怡,李自力,王桂兰,等. "节点修正"FVM-CA方法熔积凝固组织模拟[J]. 焊接学报,2013,34(11):37-40. ZHAO Jingyi,LI Zili,WANG Guilan,et al. FVM-CA simulation of grain growth during solidification sing "node-based-correction" method[J]. Transactions of the China Welding Institution,2013,34(11):37-40.
[20] ZHOU X M,ZHANG H,WANG G,et al. Simulation of microstructure evolution during hybrid deposition and micro-rolling process[J]. Journal of Materials Science,2016,51(14):6735-6749.
[21] LUO S,ZHU M,LOUHENKILPI S. Numerical simulation of solidification structure of high carbon steel in continuous casting using cellular automaton method[J]. ISIJ International,2012,52(5):823-830.
[22] KREMEYER K. Cellular automata investigations of binary solidification[J]. Journal of Computational Physics,1998,142(1):243-263.
[23] WANG W,LEE P D,MCLEAN M. A model of solidification microstructures in nickel-based superalloys:Predicting primary dendrite spacing selection[J]. Acta Materialia,2003,51(10):2971-2987.
[24] BAI X W,ZHANG H O,WANG G L. Improving prediction accuracy of thermal analysis for weld-based additive manufacturing by calibrating input parameters using IR imaging[J]. The International Journal of Advanced Manufacturing Technology,2013,69(5-8):1087-1095.
[25] GOLDAK J,CHAKRAVARTI A,BIBBY M. A new finite element model for welding heat sources[J]. Metallurgical Transactions B,1984,15(2):299-305.

电弧增材成形单道两层熔积过程中的晶粒生长模拟

Simulation of Grain Growth in Single-pass Two-layer Deposition of Arc Welding Based Additive Forming Process

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	舒林森, 王家胜, 白海清, 何雅娟, 王波. 磨损轴面激光熔覆过程的数值模拟及试验[J]. 机械工程学报, 2019, 55(9): 217-223.
[2]	徐海良, 徐聪, 曾义聪, 吴波. 固相浓度对深海采矿矿浆泵空化性能影响规律[J]. 机械工程学报, 2019, 55(8): 201-207.
[3]	闫德俊, 王赛, 郑文健, 余洋, 谢浩, 钟美达, 邹晓峰, 杨建国. 1561铝合金薄板随焊干冰激冷变形控制[J]. 机械工程学报, 2019, 55(6): 67-73.
[4]	郑乔, 逯世杰, 李索, 林旭东, 王义峰, 邓德安. 熔敷顺序和管壁厚度对异种钢管板接头焊接残余应力与变形的影响[J]. 机械工程学报, 2019, 55(6): 46-53.
[5]	吴正人, 甄猛, 刘梅, 王松岭, 刘秋升. 压力旋流喷嘴喷雾冷却热传递特性数值模拟[J]. 机械工程学报, 2019, 55(4): 172-180.
[6]	蔡志刚, 陈晓川, 王迪, 鲍劲松. 碳碳复合材料的水射流钻孔技术研究[J]. 机械工程学报, 2019, 55(3): 226-232.
[7]	魏屹, 王永祯, 王文先, 张婷婷, 闫志峰. 一次爆炸焊接制备铝/镁/铝合金复合板的数值模拟[J]. 机械工程学报, 2019, 55(14): 37-42.
[8]	张文武, 余志毅, 李泳江, 程学良. 叶片式气液混输泵全流道内流场特性分析[J]. 机械工程学报, 2019, 55(10): 168-174.
[9]	李昊, 丁晓红, 景大雷. 液冷通道分布优化设计的仿真和试验研究[J]. 机械工程学报, 2019, 55(10): 198-206.
[10]	曹嘉彬, 黄护林, 朱桂平, 李林永, 李来. 两相流磁流体发电机的性能研究[J]. 机械工程学报, 2018, 54(8): 185-191.
[11]	杜冰, 关风龙, 宋鹏飞, 韩兆建, 张鑫, 赵长财. 薄板起皱失稳数值模拟计算方法[J]. 机械工程学报, 2018, 54(24): 42-50.
[12]	王超, 孔俊超, 王伟. 考虑软三体接触的粗糙界面混合润滑模型研究[J]. 机械工程学报, 2018, 54(21): 113-119.
[13]	杨立军, 张佳, 王哲, 闫程程. 组织工程骨支架内部微孔结构流场特性分析[J]. 机械工程学报, 2018, 54(20): 71-80.
[14]	邱雅柔, 唐迪, 包士毅, 高增梁. 风诱导塔振动对塔气动特性影响研究[J]. 机械工程学报, 2018, 54(20): 106-114.
[15]	黄逸飞, 罗震, 敖三三, 樊文飞. 基于非对称热源的异种钢深熔TIG焊接数值模拟[J]. 机械工程学报, 2018, 54(2): 41-47.